Search results for "550"
showing 10 items of 1192 documents
Design and Stiffness Analysis of a 5-axis Gantry-Tau Milling Machine
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 The Gantry-Tau is a Parallel Kinematic Machine (PKM) structure that possesses many advantages as a milling machine, where it has a low moving mass, high stiffness and a large workspace to footprint ratio. This thesis presents a new milling machine design based on this structure, as a continuation of a formerly constructed prototype, see [1]. This includes selection of new actuators for the linear drives as well as the development of a new tool platform and two joint concepts. A short workspace analysis is presented on the proposed design, which includes calculation of valid workspace and an analysis on the required joint mobilit…
Implementation of Wireless Sensors on Torque Wrench
2018
Master's thesis Mechatronics MAS500 - University of Agder, 2018 Konfidensiell til / confidential until 01.07.2023
Design, Modelling and Simulation of Electro-Hydraulic Self-Contained Cylinders based on Digital Hydraulics
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 Nowadays, hydraulic cylinders are mostly powered by a separate HPU and controlled by conventional servo and proportional valves. New trends have been under development the last years. The first trend is self-contained designs where the power unit is integrated in the cylinder design. Digital hydraulics is the second new trend where conventional flow control methods are replaced by simple ON/OFF valves and digital displacement pumps. A totally novel design would be a combination of the two mentioned trends. Designing a hydraulic cylinder that combines both the self-contained method and digital hydraulics is expected to results in…
Modelling of a hydro-pneumatic system for heave compensation
2017
Masteroppgave i mekatronikk MAS500 - Universitetet i Agder 2017 Testing of control systems on simulators has been found to be both cost and time e cient. To get good results from testing, a realistic response from the simulator is important. In this thesis, a mathematical model of a hydropneumatic heave compensation system for such purposes is proposed. The emphasis has been on developing a relatively simple model which is easy to run, but also accounts for important e ects like friction, non-ideal gas behaviour and temperature variation in the gas system. The mathematical model is veri ed against log data obtained from real drilling operations. Then, it is compared to simpler versions to i…
Secondary Control of a Digital Hydraulic Motor for Winch Applications
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 The reliable traditional hydraulic systems for industrial purposes is being challenged by an emerging technology called digital hydraulics. This technology shows promising improvements in regards to e ciency, especially in comparison to systems dependent on hydraulic pumps or motors with variable displacement. Digital hydraulic motors eliminate the need for a servo valve by connecting each individual motor cylinder directly to the high-pressure and low-pressure line by means of fast-acting on/o -valves. In this thesis, the potential of digital hydraulics is investigated by developing a control system intended for a digital displ…
Fault Diagnosis of an Electrical Winch based on Structural Analysis
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 This report covers development and implementation of a model-based fault-detection and fault diagnosis algorithm based on structural analysis, providing deeper knowledge of predictive maintenance, which o ers the industry increased uptime and reduced spending. Failure mode and e ect analysis are carried out at component level for an electrical winch. Construction of a Simulink model, used to verify the algorithms, are described in detail including governing equations and implementation. The basis of a structural analysis is outlined and tested on the electrical winch system. Results from the simulation model covers faults in per…
Modelling, Simulation and Control of offshore crane Develop a kinematic and dynamic crane model and study of several control designs
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 This master thesis is about Modelling, Simulation and Control of a MacGregor Active Heave Compensation (AHC) 250t crane operating on the supply vessel Gran Canyon. The crane model was developed mathematically using robot modeling theory including both kinematic and dynamic equations. This model was developed and simulated in Matlab and Simulink and further compared, where the two models showed equal results. Control designs for an offshore crane can be developed in several ways, but in this thesis the control task only concerns position control of the crane and can be divided into two control tasks. The main goal is to determine…
Dual-speed planetary gearbox for internal mounting in winch drum : design, actuation, and control
2018
Master's thesis Mechatronics MAS500 - University of Agder 2018 Konfidensiell til / confidential until 01.07.2023
Relevance- and Aggregation-based Scheduling for Data Transmission in IEEE 802.15.4e IoT Networks
2017
Master's thesis Information- and communication technology IKT590 - University of Agder 2017 Internet of thing (IoT) is regarded as a new communicating paradigm with Internet connectivity enabling embedded devices to interact with each other on a global scale. IoT has the potential to become the largest producer of information because of a massive number of connected devices with diverse applications ranging from environmental monitoring, home, and building automation. This ubiquitous connectivity requires reliability, efficiency, and sustainability of access to information. As an enabling technology, wireless sensor networks (WSNs) have opened new opportunity with recent technological devel…
Où en est-on dans les recherches sur le Campaniforme?
2011
Cet article présente les recherches récentes sur le Campaniforme de l'Europe, recherches menées au sein du Laboratoire d'archéologie préhistorique et anthropologie de l'Institut Forel - sciences de la Terre et de l'environnement - de l'Université de Genève.