Search results for "ACOUSTIC"
showing 10 items of 1590 documents
Viscoelastic bearings with fractional constitutive law for fractional tuned mass dampers
2015
Abstract The paper aims at studying the effects of the inherent fractional constitutive law of viscoelastic bearings used as devices for tuned mass dampers. First, the proper constitutive law of the viscoelastic supports is determined by the local constitutive law. Then, the characteristic force–displacement relationship at the top of the bearing is found. Taking advantage of the whole bearing constitutive laws, the tuning of the mass damper is proposed by defining the damped fractional frequency, which is analogous to the classical damped frequency. The effectiveness of the optimal tuning procedure is validated by a numerical application on a system subjected to a Gaussian white noise.
Towards online bearing fault detection using envelope analysis of vibration signal and decision tree classification algorithm
2017
Online bearing fault detection is an important method for monitoring the health status of bearings in critical machines. This work proposes a classification algorithm, which can be extended towards an online bearing fault detection. The objective is to detect and classify the bearing faults in early stages. The overall design aspects of the online bearing fault detection and classification system are discussed. The proposed method is validated using experimental data, and a high accuracy of the fault classification was observed. Therefore, the proposed method can be applied for an online early fault detection and classification system.
Simple equipment to measure biomechanical quantities of muscles and organs which includes a polarity-programmable peak detector
1982
Biomechanical measurements of muscles and organs require appropriate measuring equipment. As far as the static properties are concerned, the excursion of the bender bar of stress should be without force. The bender bar of force, however, ideally should not elongate under load. Because natural frequency is the most important boundary condition, the bender bar should be developed with this in mind. The developed bars imposed an insignificant preload to the muscle or to the organ. The small changes in resistance occurring in the resistance strain gauges affixed to the bars require the use of a highly stable amplifier. A new amplifier was accordingly developed based on the principle of an instr…
<title>Modeling of eddy current sensors</title>
2001
In this paper two models of eddy current sensor have been presented. They are base don a one- and multi-turn coil model. The results of computer simulations present a relation of eddy current density on nonferromagnetic conducting materials versus some parameters viz: a coil radius, frequency of excitation current and conductivity of material.© (2001) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
Mismatches between objective parameters and measured perception assessment in room acoustics: a holistic approach
2014
Psychoacoustic research in the field of concert halls has revealed that many aspects concerning listening perception have yet to be totally understood. On the one hand, the objective room acoustics of performance spaces are reflected in parameters, some standardized and some not, but these are related to a limited number of perceptual attributes of human response. In general, these objective parameters cannot accurately describe the acoustic details due to their inherent simplification. Under these premises, impulse responses (576 receivers) are measured in 16 concert halls, according to standard procedures, and the perception and satisfaction of the occupants of the rooms are evaluated by …
A novel approach to current transformer characterization in the presence of harmonic distortion
2009
The current transformer (CT) performance under distorted waveform conditions is usually characterized by means of the frequency-response test. In this paper, a new way to characterize CTs, closer to real operation conditions, is proposed. The harmonic phase-angle and ratio errors are measured using a nonsinusoidal current composed of fundamental and one harmonic with adjustable phase shift. The new method was tested by determining the performance of two metering class CTs commonly used by the Italian power company. The errors measured using the proposed approach are larger than the ones obtained with the frequency response. This result suggests that the frequency-response approach for the e…
3D simulations and experiments of guided wave propagation in adhesively bonded multi-layered structures
2010
Understanding guided wave propagation in multi-layered plates and interaction with discontinuities can be difficult, as well as the interpretation of the ultrasonic signals. Propagation of guided waves can be studied analytically solving the equations of motion with the proper boundary conditions; nevertheless analytical models can be difficult to solve for complex multi-layered structures or having inner discontinuities. The problem can be efficiently studied using numerical techniques. Simulation of guided wave propagation in multi-layered structures, for ultrasonic waves in the MHz range, is solved here with the finite element analysis based on an explicit integration rule to solve the e…
Guided Wave Propagation in a Plate Edge and Application to NDI of Rail Base
2012
The analysis of guided wave propagation in a plate edge can be useful for some applications, such as for the inspection of the rail base. Here guided waves generated by a laser beam hitting, on the inclined surface, a solid media with trapezoidal cross-section have been studied. We have found that, for the geometry investigated, two guided waves propagate along both free surfaces of the plate, with same velocity and frequency. The analysis of the trajectories of the two material points, due to waves propagation, shows that the wave packets can be identified as Rayleigh waves. The presence of S0 Lamb mode, with low frequency and low amplitude, has been revealed too. As an example of a possib…
Low-cost underwater navigation systems by multi-pressure measurements and AHRS data
2017
This paper deals with accurate navigation for underwater remotely operated vehicles. A feasibility study for a multi-pressure device to be mounted on an ROV is presented. The device can provide accurate estimates of a ROV orientation and angular speed. It is based on the well-known total pressure principle, also used in a Pitot tube, and allows reconstruction of static and dynamic pressures, which in turn provide good estimates of the ROV's orientation and rotational speed, respectively. An appealing feature of the proposed device is its ability to provide accurate estimates even for low-speed movements.
A boundary element model for structural health monitoring using piezoelectric transducers
2013
In this paper, for the first time, the boundary element method (BEM) is used for modelling smart structures instrumented with piezoelectric actuators and sensors. The host structure and its cracks are formulated with the 3D dual boundary element method (DBEM), and the modelling of the piezoelectric transducers implements a 3D semi-analytical finite element approach. The elastodynamic analysis of the structure is performed in the Laplace domain and the time history is obtained by inverse Laplace transform. The sensor signals obtained from BEM simulations show excellent agreement with those from finite element modelling simulations and experiments. This work provides an alternative methodolog…