Search results for "ACOUSTIC"
showing 10 items of 1590 documents
Defect characterization in Al welded joints by non-contact Lamb wave technique
2006
Abstract The use of air-coupled sensors to detect flaws in Al welded joints and the advantage of Lamb wave for their characterization has been proved. Ultrasonic waves were generated by a pulsed laser and by contact angle-beam transducer, and received by an air-coupled capacitive transducer. Laser-based configuration was used to quickly locate the defect, whereas the angle-beam contact probe configuration to characterize it thanks to the dispersive behavior of Lamb waves. Guided waves allow inspection of the complete thickness with only one scan, permitting to detect and to size both internal and surface defects; their high flexibility in the measurement is due to the various parameters cha…
Laser ultrasonics for defect evaluation on coated railway axles
2020
Abstract This scientific paper focuses on the application of an advanced non-destructive technique for an effective inspection of railway axles. The method pertains to ultrasonic techniques, which are widely used in the railway field. The experimental investigation was carried out on simulated defects tooled near the cross section reduction of the axle, in order to simulate fatigue cracks which, due to notch effect, can trigger crack propagation and axle failure. The aim of this research activity is to evaluate how efficiently the proposed technique detects defects and to verify its applicability to axles with a black coating for protection. In view of the experimental setup, comprising a p…
Harvesting rainfall energy by means of piezoelectric transducer
2013
In this paper a detailed study on the piezoelectric energy harvesting of rainfall is presented. Different features have been taken into account in order to define the limits in this energy harvesting. Only commercial transducers have been considered: a lead zirconate titanate and polyvinylidene difluoride transducer.
Determination of the Stress Intensity Factor by Means of the Espi Technique
2007
The experimental determination of stress intensity factors by means of non-destructive techniques is a research topic of actual interest, In fact there are many applications, where a reliable and accurate experimental procedure is needed to evaluate numerical or theoretical models about the behaviour of cracked or notched structures.
Theoretical and experimental contributions on ultrasonic contactless examination of underground pipes through which pressurized fluids circulate
2019
Abstract In any civil or industrial construction, there are many embedded pipelines through which pressurized fluids or gases are circulate and which, over time, are subject to corrosion. Examination and monitoring of corrosion/erosion process in order to determine the service life of pipelines through which fluids circulate at different temperatures and / or pressures is a particularly important task for both the designer and the owner because knowledge of “health status” of these in time is extremely. On-site ultrasound control of wall thickness is based on simple propagation time measurements and is typically used to evaluate corrosion and erosion. The paper presents a non-destructive co…
Electromechanical Impedance Method to Assess the Stability of Dental Implants
2017
In this paper we illustrate the application of the electromechanical impedance (EMI) technique, popular in structural health monitoring, to assess the stability of dental implants. The technique consists of bonding a piezoelectric transducer to the element to be monitored. When subjected to an electric field, the transducer induces low to high frequency structural excitations which, in turn, affect the transducer's electrical admittance. As the structural vibrations depend on the mechanical impedance of the host structure (in this case the implant secured to the jaw), the measurement of the PZT's admittance can infer the progress of the osseointegration process. In the study presented in th…
Effect of Ni content on the structure and hydrogenation property of mechanically alloyed TiMgNix ternary alloys
2017
Abstract In this study, TiMgNix samples (x = 0.2, 0.4, 0.6, 0.8, 1) have been prepared by mechanical alloying using a planetary high-energy ball mill. The structural transformations were characterized by XRD and indicated that all the as-milled TiMgNix alloys consist of mixtures of crystalline Mg and amorphous Ti-Ni-(Mg) phase. TEM analyses also show that nanocrystallites and amorphous phases coexist in the as-milled TiMgNi alloy. Electrochemical test shows that the TiMgNi composition yields the highest discharge capacity. The discharge capacities and activation properties of TiMgNix alloys linearly increase with increasing Ni content. The MgTiNi0.8 composition boasts the best cycling prope…
The influence of the temperature of insulation oil on the results of measurements of the acoustic emission signals generated by partial discharges
2005
The subject matter of this paper refers to the improvement of the acoustic emission method (AE) used for evaluation of partial discharges (PDs) generated in paper-oil insulation systems of power appliances. The paper presents the measurement and analysis results of the AE signals generated by partial discharges of the surface type (SPDs). The AE signals were measured on the surface of a transformer tub using a broad-band contact transducer, and then they were subject to a time-frequency analysis. The measurements were taken while heating transformer oil in the range from 30 to 85°C with gradation of every 5°C. For time runs, amplitude and energy density spectra the descriptor values that ch…
Intentional weld defect process: From manufacturing by robotic welding machine to inspection using TFM phased array
2019
Specimens with intentionally embedded weld defects or flaws can be employed for training, development and research into procedures for mechanical property evaluation and structural integrity assessment. It is critical that the artificial defects are a realistic representation of the flaws produced by welding. Cylindrical holes, which are usually machined after welding, are not realistic enough for our purposes as it is known that they are easier to detect than the naturally occurring imperfections and cracks. Furthermore, it is usually impractical to machine a defect in a location similar to where the real weld defects are found. For example, electro-discharge machining can prod…
Characterization of the Optimal Damping Coefficient in the Continuous Contact Model
2020
AbstractThis paper presents an analytical formula to characterize the damping coefficient as a function of system's parameters in a continuous force model of impact. The contact force element consists of a linear damper which is in a parallel connection to a spring with Hertz force-deformation characteristic. Unlike the existing models in which the separation condition is assumed to be at the time at which both zero penetration (deformation) and zero force occur, in this study, only zero contact force is considered as the separation condition. To ensure that the continuous contact model obtains the desired restitution, an optimization process is performed to find the equivalent damping coef…