Search results for "ALS"

Luminescence of divalent lanthanide doped BaBrI single crystal under synchrotron radiation excitations

2020

Abstract Luminescence excitation spectra of BaBrI single crystals doped by divalent lanthanide ions are studied using synchrotron radiation excitations from the MAX IV 1.5 GeV storage ring. The energy of the edge and the formation of core cation exciton as well as the energy threshold of the multiplications of electronic excitations is found. It was clearly established the energy transfer from intrinsic luminescence centers to Sm2+ and Eu2+ ions.

Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel

2019

Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …

New fine structures resolved at the ELNES Ti-L2,3 edge spectra of anatase and rutile: comparison between experiment and calculation.

2010

Abstract Anatase and rutile Ti- L 2,3 edge spectra were measured in electron energy loss spectroscopy (EELS) using a transmission electron microscope (TEM) coupled to a CEOS Cs-probe corrector, an omega-type monochromator and an in-column omega-type energy filter fully corrected for 2nd order aberrations. Thanks to the high energy resolution, high electron probe current and high stability achieved under this instrumental configuration, new fine structures, never reported before, were resolved at the L 3 band of both rutile and anatase. The data suggest that new peaks also exist in the L 2 e g band. The experimental spectra are compared with multichannel multiple scattering (MMS) calculation…

Exploring the transport properties of equatorially low coordinated erbium single ion magnets

2019

Single-molecule spin transport represents the lower limit of miniaturization of spintronic devices. These experiments, although extremely challenging, are key to understand the magneto-electronic properties of a molecule in a junction. In this context, theoretical screening of new magnetic molecules provides invaluable knowledge before carrying out sophisticated experiments. Herein, we investigate the transport properties of three equatorially low-coordinated erbium single ion magnets with C3v symmetry: Er[N(SiMe3⁠)2⁠]3⁠ (1), Er(btmsm)3⁠ (2) and Er(dbpc)3⁠ (3), where btmsm=bis(trimethylsilyl)methyl and dbpc=2,6-di-tert-butyl-p-cresolate. Our ligand field analysis, based on previous spectros…

Magnetization switching behavior with competing anisotropies in epitaxial Co3FeN/MnN exchange-coupled bilayers

2016

Key factors towards a high-quality additive manufacturing process with ABS material

2019

Abstract Additive Manufacturing technologies have gained a lot of popularity during the past years. The current challenge being the transition of this manufacturing technology from prototype oriented towards mass production. In order to achieve this, fabrication times and mechanical parameters must be improved. This paper aims to identify which are the parameters that have the highest influence on parts obtained with fused deposition modeling (FDM) technology from ABS material. In addition, this study identifies which are the most accurate methods to test the mechanical properties of FDM parts while still respecting ASTM standard for testing the tensile properties of plastics. It was found …

Cold gas dynamic spray additive manufacturing today: Deposit possibilities, technological solutions and viable applications

2017

This paper reports the current potentials of cold gas dynamic spraying (CGDS). CGDS has been significantly developed to produce several functional solutions categorized as follows: deposits with a single powder nature, composites-based deposits, nanotechnological deposits and hybrid coating/substrate assemblies. CGDS process has improved in proficiency and is still gaining attention from scientists and industry. Covering a wide range of materials, both standard and advanced, this additive manufacturing process offers substantial applications for surface functionalization, structural or dimensional restoration, bulk production providing specific material properties, and art/decoration. Progr…

Mass recovery of carbonated fabrics of glass fibres after isothermal heating

2019

Acknowledgement: Authors acknowledge financial support from Latvian National Program IMIS2

Metallurgical Strategies for the Joining of Titanium Alloys with Steels

2018

Physical properties and microstructure characteristics of (1–x)BaTiO3–xCaTiO3 systems

2018

The study investigates the microstructure, thermal and mechanical properties of (1–x)BaTiO3–xCaTiO3 ((1–x)BT–xCT)) (x = 0.01, 0.04, 0.08) samples. The BT–CT system to be tested was formed as a soli...