Search results for "Adsorbents"
showing 5 items of 5 documents
Sewage Sludge Derived Materials for CO2 Adsorption
2021
The study tried to contribute to solving two serious environmental issues: CO2 reducing and sewage sludge disposal. Thus, sewage-sludge-derived materials were obtained in order to be evaluated for CO2 adsorption capacity. Therefore, the char resulted after the sewage sludge pyrolysis was subjected to oxidation and chemical activation processes by using different quantities of alkaline hydroxide. One of the obtained materials, activated with a lower quantity of alkaline hydroxide, was also treated with acid chloride. Further, the materials were structural and texturally characterized, and material treated with acid chloride was used for CO2 adsorption tests, due to high surface area and pore…
Ceramic foam supported active materials for boron remediation in water
2015
Due to the narrowrange between boron necessities and toxicity in the environment, there is a high interest in the design of effective boron remediation procedures. We have previously reported a promising boron adsorptionmaterial based on the affinity of boron aqueous species for cis-diol groups that were anchored on differentmesoporous silica matrices.However, the small particle size of these systemsmakes themdifficult to be applied on real remediation situations. In this context we report herein a novel systemfor boron adsorption fromaqueous solutions inwhich the high boron affinity for functionalized mesoporousmaterials is combined with themechanical properties of ceramic foams as macrosc…
Development of iron oxide/activated carbon nanoparticle composite for the removal of Cr(VI), Cu(II) and Cd(II) ions from aqueous solution
2018
Iron oxide (Fe3O4) and iron oxide/activated carbon (Fe3O4/AC) were fabricated by co-precipitation method for the removal of Cr(VI), Cu(II) and Cd(II) ions from aqueous solution in batch mode. These nanoparticles were characterized by BET, FTIR, XRD, SEM/TEM and VSM. The optimum conditions for the removal of ions were pH = 2 for Cr(VI) and 6 for Cu(II) and Cd(II), initial metal ion concentration = 50 mg L−1, nanoparticle dose = 50 mg/10 mL, temperature = 25 ± 1 °C, shaking speed = 180 rpm and contact time = 3 h. The equilibrium data of ions sorption were well described by Langmuir, Freundlich, Redlich-Peterson and Intraparticle Diffusion model. The R2 values obtained by Langmuir model were h…
Evaluation of sampling adsorbents and validation of a LC-HRMS method for determination of 28 airborne pesticides
2018
A new strategy for sampling, using a low-volume sampler, and determination of airborne pesticides by liquid chromatography coupled to high-resolution mass spectrometry (UHPLC-HRMS) has been developed. The trapping efficiency of three adsorbents (sandwich PUF-XAD2-PUF; XAD-2 and XAD-4) was tested for 33 currently used pesticides and the first adsorbent (PUF-XAD2-PUF) was selected because it presented the highest retention capacity without breakthrough. Selected PUF-XAD2-PUF had the following design: 5 g of Amberlite XAD-2 sandwiched between two cylinders of PUF (6.87 cm(3), height: 1.4 cm, diameter: 2.5 cm). A validation of the analytical methodology that includes microwave extraction with e…
Selection of sampling adsorbents and optimisation and validation of a GC-MS/MS method for airborne pesticides
2017
ABSTRACTA methodology for the sampling and determination of airborne pesticides has been developed. The trapping efficiency of three adsorbents, namely XAD-2,XAD-4 and a sandwich sorbent (PUF-XAD2-PUF), was tested for 34 pesticides and the latter was selected because it presented the highest retention capacity without breakthrough. Pesticides were determined by gas chromatography coupled to an ion trap mass spectrometer in tandem. The method showed recoveries ranging from 70% to 120% with limits of quantification in the range of 16.1–322.6 pg m−3 when 155 m3 were sampled. This analytical strategy was applied to 10 indoor air samples collected in dwellings from the Valencian Region. Six pest…