Search results for "Alum"
showing 10 items of 1303 documents
CCDC 1952094: Experimental Crystal Structure Determination
2020
Related Article: Xueer Zhou, Petra Vasko, Jamie Hicks, M. Ángeles Fuentes, Andreas Heilmann, Eugene L. Kolychev, Simon Aldridge|2020|Dalton Trans.|49|9495|doi:10.1039/D0DT01960G
CCDC 1952093: Experimental Crystal Structure Determination
2020
Related Article: Xueer Zhou, Petra Vasko, Jamie Hicks, M. Ángeles Fuentes, Andreas Heilmann, Eugene L. Kolychev, Simon Aldridge|2020|Dalton Trans.|49|9495|doi:10.1039/D0DT01960G
CCDC 1854972: Experimental Crystal Structure Determination
2019
Related Article: Jamie Hicks, Akseli Mansikkamäki, Petra Vasko, Jose M. Goicoechea, Simon Aldridge|2019|Nature Chemistry|11|237|doi:10.1038/s41557-018-0198-1
CCDC 205740: Experimental Crystal Structure Determination
2004
Related Article: A.Antinolo, I.Dorado, M.Fajardo, A.Garces, I.Lopez-Solera, C.Lopez-Mardomingo, M.M.Kubicki, A.Otero, S.Prashar|2004|Eur.J.Inorg.Chem.||1299|doi:10.1002/ejic.200300530
Determination of an empirical law of aluminium and magnesium alloys absorption coefficient during Nd :YAG laser interaction
2007
International audience; Welding laser modelling requires knowledge about relative changes of many thermo-physical parameters involved in the interaction. The absorptivity of the material is one of the most important. In this study, experimental measurements of absorptivity with an integrating sphere on two alloys (aluminium and magnesium) were made. These results were compared with an analytical calculation that takes into account the trapping of the beam by multiple reflections inside the keyhole. Based on a statistical method, an empirical law is proposed connecting absorptivity with the peak power of the laser and the duration of interaction. During the interaction, two distinct phenomen…
Savaime sklindančios aukštatemperatūrinės sintezės būdu gautų aliuminio oksinitrido miltelių ir jų keramikų optinės savybės
2021
The reported study was funded by RFBR according to the Research Project No. 19-08-00655. V.P. acknowledges the State Research Program ‘Aug-stas enerģijas fizika un paātrinātāju tehnoloģijas’ (Projekta Nr. VPP-IZM-CERN-2020/1-0002). The Institute of Solid State Physics, University of Latvia as the Center of Excellence has received funding from the H2020-WIDESPREAD-01-2016-2017-Teaming Phase2 under Grant Agreement No. 739508, Project CAMART2.
Batch-to-Melt Conversion Kinetics in Sodium Aluminosilicate Batches Using Different Alumina Raw Materials
2016
The batch-to-melt conversion in batches of sand, soda ash and corundum (C), alumina spinel (A), boehmite (B), or gibbsite (G) as Al2O3 carrier are studied using thermal analysis, X-ray diffraction, and 27Al nuclear magnetic resonance spectroscopy. Laboratory-scaled batches are either heated continuously or quenched from 1600°C in a series of increasing dwell times. The results show that the conversion from the raw materials to the fresh melt proceeds in two kinetic stages. During the first stage (3–5 min), fast conversion of nearly 95% by mass occurs and the conversion coefficient increases in the order G < C ≈ A < B. The second stage is controlled by the slow dissolution of intermediate cr…
Electromagnetic and Thermal Modelling for Calculating Ageing Rate of Distribution Transformers
2018
Prediction of the lifetime for transformers is very important for maintenance and asset management. Finite element analysis was performed on a 5 MVA distribution transformers with aluminium foil-type windings and voltage rating 6600 V/23000 V. Electromagnetic modelling is implemented on the full three-phase transformer to calculate distributed losses, taking the skin effect into account. To reduce the computational burden, the distributed losses in one phase are used to analyse temperature rise in one phase of the transformer. The temperature rise results were used to determine the ageing rate of the transformer. Further, the influence of ambient temperature and cooling on the temperature r…
An anomalous wave formation at the Al/Cu interface during magnetic pulse welding
2020
This paper reports an anomalous wave formation at an Al/Cu bimetallic interface produced by magnetic pulse welding. The mechanism of the anomalous wave formation is investigated using both metallurgical characterization and the interface kinematics. It reveals that the anomalous wave is formed with the combination of the intermediate zone and the interdiffusion zone with a thickness of 70 nm, wherein the intermediate zone is caused by the local melting due to the high shear instability, and the interdiffusion zone is formed below the melting point of aluminum combined with ultrahigh heating and cooling rates of about 10^13 °C s^−1. A multiphysics simulation of impact welding has been perfor…
Experimental and numerical investigation on a new FSW based metal to composite joining technique
2018
Abstract In the last decades, different techniques were proposed to join aluminum sheets with composites materials. Each of them has advantages and weak points over the others and new techniques and patents are continuously developed to overcome these difficulties. In this paper an experimental and numerical investigation on a new Friction Stir Welding based approach to mechanically join AA6082-T6 to self-reinforced polypropylene is presented. The aluminum sheet is pre-holed along both the sides of the weld line and a pinless tool generates the heat and pressure needed to prompt back-extrusion of the composite. New experimental fixtures and hole designs were investigated in order to enhance…