Search results for "Aluminium"
showing 10 items of 548 documents
The anodic and cathodic dissolution of Al and Al–Cu–Mg alloy
2010
Abstract Atomic emission spectroelectrochemistry (AESEC) was used to monitor the release of Al from 99.99% aluminum (1199 alloy) and Al, Mg, and Cu from 2024 Al alloy in 30 g/l NaCl electrolyte as a function of pH. The cathodic dissolution of Al was demonstrated and attributed to an increase in the pH at the interface due to the water reduction reaction. The dissolution of Mg was also observed but was a more complex function of current probably depending on the interfacial pH and the Al dissolution rate. The detachment of copper-rich particles was observed as very rapid spectroscopic emission transients (peak width
Über die Inhibitoren der Korrosion IV(1). Versuche zur Unterdrückung der Auflösung von Aluminium durch organische Substanzen in saurer und alkalische…
1965
Oniumsalze oder potentielle Oniumsalze sind wirksame Inhibitoren der Auflosung von Aluminium in Salzsaure. Ihr Schutz ist im alkalischen Medium geringer. Corrosion Inhibitors IV. Investigations into the suppression of the dissolution of aluminium by organic substances in acid and alkaline solution Onium salts or potential onium salts are effective inhibitors in respect of the dissolution of aluminium in hydrochloric acid. In the alkaline medium, the protective effect is less marked.
Gold catalysts supported on CeO2 and CeO2–Al2O3 for NO reduction by CO
2006
Abstract The reduction of NO x by CO was studied over gold catalyst supported on ceria and ceria–alumina. The mixed supports with different CeO 2 /Al 2 O 3 ratios were prepared by co-precipitation. The catalysts were characterized by means of XRD, TPR, XPS and Raman spectroscopy. The addition of alumina led to a slight enlargement of the gold particles, while the ceria particle size was decreased. Deeper oxygen vacancies formation in the presence of alumina was detected by TPR, XPS and Raman spectroscopy, compared to the pure ceria support. The samples exhibited a high and stable activity and 100% selectivity towards N 2 was reached at 200 °C.
Spectrophotometric determination of fluoride in fluoride-bearing minerals after decomposition by fusion with sodium hydroxide
1984
The decomposition of highly insoluble minerals (fluorspar and cryolite) by fusion with molten alkali-metal hydroxides is studied. The introduction of additives such as aluminium compounds or sodium peroxide to obtain total liberation of fluoride from calcium fluoride samples, is tested. The fusion is done in a silver crucible with a Bunsen burner. The cooled melt is easily soluble, giving solutions suitable for spectrophotometric fluoride determination by the Zr(IV)-fluoride-Erichrome Cyanine R method.
Novel synthesis of spherical MCM-48
1999
Abstract A novel synthesis route was developed for the cubic member of the M41S family, MCM-48, with a three-dimensional pore system allowing the formation of submicrometre- to micrometre-sized beads with a narrow pore-size distribution. The synthesis is based on the modified Stober method applying tetraethoxysilane, ethanol, water, ammonia and n -hexadecyltrimethylammonium bromide as template. The specific surface area, the specific pore volume and the average pore diameter were varied in the following ranges: 900–1600 m 2 g −1 , 0.5–0.9 cm 3 g −1 and 2–3 nm. Aluminium-, chromium-, gallium-, niobium- and vanadium-MCM-48 were also synthesized following this procedure.
Determination of metal inventory and current efficiency in commercial aluminum reduction cells
1971
A method for the determination of the metal inventory in commercial aluminum reduction cells, based on radioisotope dilution, has been developed, employing a198Au tracer. By taking a large number of samples from the cells, the current efficiency is evaluated from the slope of the cumulative metal inventory vs time data. The method allows a determination of the current efficiency over a period of 2 to 3 days with a relative precision of approximately 1 pct. The paper gives a thorough discussion of the sources of error inherent in the procedure suggested.
Magnesium alloys laser (Nd:YAG) cladding and alloying with side injection of aluminium powder
2003
International audience; The development of the high purity magnesium alloys (such as WE43) incites the designers to reconsider them, and the car industry appears, these days, the most interested to use this kind of alloy. However, due to their ignitability and tendency to oxidation, magnesium alloys require surface treatments. A series of experiments was carried out in order to improve the corrosion resistance of two types of magnesium alloys, WE43 and ZE41. In most cases, the substrate surface was treated before laser interaction. Side injection of aluminium powder under a 3 kW cw Nd:YAG laser was employed. The deposited layers present very good bond properties. The resulting microstructur…
Effect of the indentation process on fatigue life of drilled specimens
2015
Design and manufacture of mechanical elements are strongly influenced by the evaluation of the residual stresses due to their effects on the material strength. This paper presents numerical and experimental results performed on AW 6082-T6 aluminum alloy drilled specimens when the hole is created after a bilateral indentation process. The plastic deformation induced by the indenters creates a compressive residual stress field around the hole, which persists after the drilling operation. Several numerical analysis have been carried out in ANSYS APDL explicit solver for different indentation depths and hole diameters in order to evaluate the compressive circumferential stresses, optimal proces…
Structure and transport properties of amorphous aluminium silicates: computer simulation studies
2005
The structure and transport properties of SiO2-Al2O3 melts containing 13 mol% and 47 mol% Al2O3 are investigated by means of large scale molecular dynamics computer simulations. The interactions between the atoms are modelled by a pair potential which is a modified version of the one proposed by Kramer et al. [J. Am. Chem. Soc. 64, 6435 (1991)]. Fully equilibrated melts in the temperature range 6000 K >= T > 2000 K are considered as well as glass configurations, that were obtained by a rapid quench from the lowest melt temperatures. Each system is simulated at two different densities in order to study the effect of pressure on structural and dynamic properties. We find that the Al ato…
Direct chill casting of aluminium alloys under electromagnetic interaction by permanent magnet assembly
2018
Direct chill casting is one of the methods used in industry to obtain good microstructure and properties of aluminium alloys. Nevertheless, for some alloys grain structure is not optimal. In this study, we offer the use of electromagnetic interaction to modify melt convection near the solidification interface. Solidification under various electromagnetic interactions has been widely studied, but usually at low solidification velocity and high thermal gradient. This type of interaction may succeed fragmentation of dendrite arms and transport of solidification nuclei thus leading to improved material structure and properties. Realization of experimental small-scale crystallizer and electromag…