Search results for "Austen"
showing 10 items of 68 documents
Structural characterization and electrochemical hydrogen storage properties of Ti2LxZrxNi (x [ 0, 0.1, 0.2) alloys prepared by mechanical alloying
2013
International audience; Nominal Ti2Ni was synthesized under argon atmosphere at room temperature using a planetary high-energy ball mill. The effect of milling time and Zr substitution for Ti on the microstructure was characterized by XRD, SEM and TEM, and the discharge capacities of Ti2xZrxNi (x 1/4 0, 0.1, 0.2) were examined by electrochemical measurements at galvanostatic conditions. XRD analysis shows that amorphous phase of Ti2Ni can be elaborated by 60 h of milling, whereas Zr substitution hinders amorphization process of the system. The products of ball milling nominal Ti2xZrxNi (x 1/4 0.1, 0.2) were austenitic (Ti, Zr)Ni and partly TiO, despite the fact that the operation was carrie…
Strain detection in non-magnetic steel by Kerr-microscopy of magnetic tracer layers
2018
Abstract For many applications of steel, e.g. for the evaluation of the fatigue state of components or structures, the characterization of the microscopic strain distribution in the material is important. We present a proof-of-principle for the visualization of such strain distributions by Kerr-microscopy of ferromagnetic tracer layers on nonmagnetic steel sheets. The influence of indentation induced strain on the magnetic domain pattern of 20 nm Galfenol and Permalloy tracer layers on austenitic AISI 904L steel sheets was investigated. The obtained Kerr-microscopy images show a characteristic domain pattern in the strained regions of the steel sheets, which is consistent with a dominant ma…
Direct laser welding of pure titanium to austenitic stainless steel
2018
Abstract Direct butt joining of pure titanium to 316L stainless steel with continuous Yb:YAG laser was performed with variation of the beam offset from joint line. Mechanical properties of samples were evaluated by tensile tests and three-point flexural tests. The fractured surfaces and cross sections of welds were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Tensile properties of welds were strongly determined by the beam offset from joint line and are well described by Weibull statistics. Ultimate tensile strength of 174 ± 69 MPa and ultimate flexural strength of 297 ± 48 MPa were obtained. Brittle fracture took place in…
Influence of the dissolution of MnS inclusions under free corrosion and potentiostatic conditions on the composition of passive films and the electro…
2006
Abstract The influence of the dissolution of MnS inclusions at the OCP value and 400 mV versus SCE on the chemical composition of passive films and the electrochemical behaviour of resulfurized austenitic stainless steel was studied in 1 M NaClO 4 , pH 3, solution using SIMS, XPS, electrochemical impedance spectroscopy and the electrochemical microcell technique. The electrochemical dissolution (at 400 mV versus SCE) of inclusions occurred uniformly along the interface and this process was almost complete after 25 min immersion. A small amount of sulfur was detected on the matrix that exhibited a wide passive range. By contrast, the dissolution process under free corrosion was not uniform a…
SVET, AFM and AES study of pitting corrosion initiated on MnS inclusions by microinjection
2003
As pitting is a random phenomenon, it is difficult to predict where a pit will appear on the surface and consequently the use of local probes is rendered difficult. In this work, a new method to study pitting corrosion on a MnS inclusion on 316L stainless steel is proposed. It consists in modifying locally the chemistry in its vicinity by injecting with a microcapillary an aggressive solution of NaCl, H2SO4 or HCl. Once a pit appears, scanning vibrating electrode technique (SVET) is used to follow the current fluctuations over and around the pit when the metal is polarized at a passive potential. In another series of experiments the effect of local activation of MnS inclusion was studied ex…
Sempre pazzi per Jane Austen
2014
The article’ deals with Jane Austen’s novels (with special reference to "Mansfield Park"), and with their lasting success.
Influence of the passive film properties and residual stresses on the micro-electrochemical behavior of duplex stainless steels
2010
In the present paper, the chemical composition of passive films formed on both phases of two types of duplex stainless steels (UNS S31803 and UNS S32304) is determined at the micro-scale using Auger electron spectroscopy (AES). Samples were either mechanically polished (down to diamond pastes) or electrochemically etched in acidic solutions. The micro-electrochemical behavior of samples was then determined in sodium chloride media by means of the electrochemical micro-cell technique (capillary diameters of 30 μm). The results obtained were analyzed considering the passive film chemical composition. Quantitative relationships between electrochemical parameters and the distribution of chromiu…
An integrated approach to evaluating the tribo-contact for coated cutting inserts
2000
Abstract The orthogonal machining process when end turning medium carbon and austenitic stainless steels with cemented WC-Co tools coated with single-layer (TiC), two-layer (TiC/TiN), and three-layer (TiC/Al2O3/TiN) hard thin films was investigated. Extensive experimental investigations including the thermal, mechanical and tribological responses of the tribo-contact between the coating–substrate system and the chip, under different cutting conditions, were carried out. The study sheds light on the cutting forces, the interface temperatures and the tribo-contact conditions, including the friction energy dissipated at the tool–chip interface, the frictional heat flux conducting into either t…
Corrosion Phenomena of Eurofeer Steel in Pb-17Li Stationary Flow at Magnetic Field
2006
Search of new energy sources draws the increasing attention to use for this purpose of reactors. In the Europe some years the program EUROATOM uniting scientific of the many countries for the decision of constructive problems at designing of fusion reactors operates. One of the main things in this program is the problem of liquid metals breeder blanket behaviour. Structural material of blanket should meet high requirements because of extreme operating conditions. Therefore the knowledge of the effect of metals flow velocity, temperatures and also a neutron irradiation and a magnetic field on the corrosion processes are necessary. At the moment the eutectic lead -lithium (Pb-17Li) is conside…
Effect of Plastic hot deformation on the hardness and continuous cooling transformations of 22MnB5 micro-alloyed boron steel
2009
The strains, transformation temperatures, microstructure, and microhardness of a microalloyed boron and aluminum precoated steel, which has been isothermally deformed under uniaxial tensile tests, have been investigated at temperatures between 873 and 1223 K, using a fixed strain rate value of 0.08 s−1. The effect of each factor, such as temperature and strain value, has been later valued considering the shift generated on the continuous cooling transformation (CCT) diagram. The experimental results consist of the starting temperatures that occur for each transformation, the microhardness values, and the obtained microstructure at the end of each thermomechanical treatment. All the thermome…