Search results for "Base"
showing 10 items of 8362 documents
A knowledge-based master model approach exemplified with jet engine structural design
2017
Successful product development requires the consideration of multiple engineering disciplines and the quantification of tradeoffs among conflicting objectives from the very early design phases. The single-largest challenge to do so is the lack of detailed design information. A possible remedy of this issue is knowledge-based engineering. This paper presents a knowledge-based master model approach that enables the management of concurrent design and analysis models within different engineering disciplines in relation to the same governing product definition. The approach is exemplified on an early phase structural design of a turbo-fan jet engine. The model allows geometric-, structural mech…
Design of a modular Autonomous Underwater Vehicle for archaeological investigations
2015
MARTA (MARine Tool for Archaeology) is a modular AUV (Autonomous Underwater Vehicle) designed and developed by the University of Florence in the framework of the ARROWS (ARchaeological RObot systems for the World's Seas) FP7 European project. The ARROWS project challenge is to provide the underwater archaeologists with technological tools for cost affordable campaigns: i.e. ARROWS adapts and develops low cost AUV technologies to significantly reduce the cost of archaeological operations, covering the full extent of an archaeological campaign (underwater mapping, diagnosis and cleaning tasks). The tools and methodologies developed within ARROWS comply with the "Annex" of the 2001 UNESCO Conv…
Robustness with Respect to Delay Uncertainties of a Predictor-Observer Based Discrete-Time Controller
2006
This paper focuses on the delay-dependent stability problem of a discrete-time prediction scheme to stabilize possible unstable continuous-time systems. The delay-dependent stability condition is expressed in terms of LMIs. The separation principle between the proposed predictor and a state observer is also proved. The closed-loop system is shown to be robust with respect to uncertainties in the knowledge on the plant parameters, the delay and the sampling period. The proposed scheme has been tested in a real-time application to control the roll angle in a prototype of a quad-rotor mini-helicopter.
A Humanoid Social Robot Based Approach for Indoor Environment Quality Monitoring and Well-Being Improvement
2020
The indoor environmental quality (IEQ) monitoring inside buildings where people spend most of their time is essential for ensuring their well-being. Traditional approaches based on Building Automation and Control Systems consider buildings equipped with many different sensors. Unfortunately, the sensors are not always placed for taking the measurements at the right positions. Besides, users could feel a negative perception due to continuous supervision. The present work proposes an approach based on a social humanoid robot that monitors indoor environmental quality. It friendly interacts with occupants providing appropriate suggestions. Particularly, the social robot has been endowed with c…
Impact of accounting process characteristics on accounting outsourcing - Comparison of users and non-users of cloud-based accounting information syst…
2019
Article In Press The article of record as published may be found at https://doi.org/10.1016/j.accinf.2019.06.002 Prior literature informs us that a company's decision to outsource a business process depends on process characteristics such as how frequently the process is performed or how specific the assets required by the process are. In this article, we compare the effects of accounting process characteristics on outsourcing decisions across users of traditional and cloud-based accounting information systems (AIS). By focusing on outsourcing of accounting processes among small and medium sized enterprises, we investigate the effect of five business process characteristics (frequency, huma…
A Hierarchical Learning Scheme for Solving the Stochastic Point Location Problem
2012
Published version of a chapter in the book: Advanced Research in Applied Artificial Intelligence. Also available from the publisher at: http://dx.doi.org/10.1007/978-3-642-31087-4_78 This paper deals with the Stochastic-Point Location (SPL) problem. It presents a solution which is novel in both philosophy and strategy to all the reported related learning algorithms. The SPL problem concerns the task of a Learning Mechanism attempting to locate a point on a line. The mechanism interacts with a random environment which essentially informs it, possibly erroneously, if the unknown parameter is on the left or the right of a given point which also is the current guess. The first pioneering work […
Calibration of mobile manipulators using 2D positional features.
2018
International audience; Robotic manipulators are increasingly being attached to Automatic Ground Vehicles (AGVs) to aid in the efficiency of assembly for manufacturing systems. However, calibrating these mobile manipulators is difficult as the offset between the robotic manipulator and the AGV is often unknown. This paper provides a novel, simple, and low-cost method for calibrating and measuring the performance of mobile manipulators by using data collected from a laser retroreflector that digitally detects the horizontal two-dimensional (2D) position of reflectors on an artifact as well as a navigation system that provides the heading angle and 2D position of the AGV. The method is mathem…
Intelligent agents for feature modelling in computer aided design
2017
Abstract CAD modelling can be referred to as the process of generating an integrated multiple view model as a representation of multiple views of engineering design. In many situations, a change in the model of one view may conflict with the models of other views. In such situations, the model of some views needs to be adapted in order to make all models consistent. Thus, CAD models should be capable of adapting themselves to new situations. Recently, agent based technologies have been considered in order to increase both knowledge level and intelligence of real and virtual objects. The contribution of this paper consists in introducing the intelligent agents in intelligent CAD modelling. T…
Design of a robust controller for DC/DC converter–electrolyzer systems supplied by μWECSs subject to highly fluctuating wind speed
2020
Abstract A buck-based, isolated, high-voltage-ratio DC/DC converter that allows supplying a proton exchange membrane (PEM) electrolyzer from a micro-wind energy conversion system ( μ WECS) has been recently presented. It exhibits low ripple at the switching frequency on the output voltage and current and represents an attractive solution for low-cost hydrogen production. In this paper, a more accurate mathematical model of such a converter is derived and discussed. Then, a model-based robust controller is designed in the frequency domain using the Internal Model Control structure and in the context of H 2 ∕ H ∞ optimal control. The controller satisfies the condition of robust stability and …
Interoperable real-time symbolic programming for smart environments
2019
Smart environments demand novel paradigms offering easy configuration, programming and deployment of pervasive applications. To this purpose, different solutions have been proposed ranging from visual paradigms based on mashups to formal languages. However, most of the paradigms proposed in the literature require further external tools to turn application description code into an executable program before the deployment on target devices. Source code generation, runtime upgrades and recovery, and online debugging and inspection are often cumbersome in these programming environments. In this work we describe a methodology for real-time and on-line programming in smart environments that is co…