Search results for "Bending"
showing 10 items of 244 documents
Partial Elastic Scheme Method in Cantilever Construction of Concrete Arch Bridges
2013
AbstractIn this paper, a study about stay stressing procedures of concrete arch bridges built by cantilevering with temporary stays is presented. Particularly, the partial elastic scheme method is proposed to find the initial cable forces, and a forward procedure is implemented to follow the actual sequence of construction by extending a procedure already applied to concrete cable–stayed bridges. The theoretical treatment is followed by a numerical application on a case study of a concrete arch bridge, and a comparison between initial cable forces found by the partial elastic scheme method and classical backward analysis is presented here. Results show the effectiveness of the proposed proc…
A parametric study of curved incrementally launched bridges
2013
Abstract The structural behaviour of incrementally launched bridges in the construction stages depends on different parameters involving deck, nose, supports and guide devices, because static schemes vary continuously with the advance of the deck above the piers. For this reason temporary stresses in the deck, during launching, are rather different from those occurring in service life. Horizontally curved launched bridges also present the effects of torsion induced by geometric curvature. A parametric study is presented in order to analyse the influence of design parameters on the construction of these bridges. Analyses were carried out by extending to curved beams a procedure based on the …
A practical approach for the strength evaluation of RC columns reinforced with RC jackets
2015
Abstract Reinforced concrete (RC) jacketing is nowadays one of the most common techniques adopted for seismic retrofitting of existing RC columns. It is used to increase load-carrying capacity and ductility of weak existing members by means of a simple and cheap method. The structural efficiency is related to two main effects: – the enlargement of the transverse cross section; – the confinement action provided by the external jacket to the inner core. Several theoretical and experimental studies were addressed in the past to investigate on how it is possible to calculate the strength enhancement due to these effects and to highlight the main key parameters influencing the structural behavio…
Load carrying capacity of RC compressed columns strengthened with steel angles and strips
2012
Abstract In this paper a comparison between the analytical expressions for the prediction of the load carrying capacity of strengthened reinforced concrete (RC) columns with steel angles and strips is made. Expressions examined consider: the strength contribution due to the confinement effects induced by transverse strips; the composite action due to steel angles and unconfined concrete core; the strength contribution due to the composite actions of angles and concrete core taking into account that steel angles are subjected to axial force and bending moment and concrete core is confined by transverse strips. Design rules given by recent codes for the design of the strengthened columns are …
Adjustable prestressing for construction stages of incrementally launched bridges
2014
Incrementally launched bridges, which are generally built with the static scheme of a continuous beam on supports, change their scheme several times during launching. In these different configurations, internal forces vary and bending moments of opposite signs occur in the same sections for different positions of deck during advancement. In these bridges, two different kinds of prestressing are necessary: a temporary one during launching and a definitive one in service life. In this study, the possibility of implementing automatic adjustable prestressing for the launching stages is investigated; the launch prestressing is partially supplied by a system which can change the tension value in …
Friction Stir Welding of AA6082-T6 T-joints: Process Engineering and Performance Measurement
2006
In the paper the authors present the results of a wide range of experiments on T-parts. First, friction stir welding process engineering has been developed with the aim of determining the specific process parameters that make up the soundness of the obtained T-parts. Then the performance of the obtained T-joints has been compared with T-joints obtained by metal inert gas welding and extruded T-parts. The parts have been tested utilizing a customized bending test with the aim of highlighting their behaviour both in elastic and plastic fields.
Behaviour of a speargun with a novel muzzle - Comportamento di un fucile subacqueo con testata innovativa
2013
The paper presents the results of a numerical and experimental investigation performed on a barrel of a speargun equipped with two kinds of muzzle. In particular, a standard muzzle for speargun (having an elastic propulsion) has been compared with an innovative one called ‘roller’. This new muzzle is equipped with two rollers and special bands. The rubber bands, fixed at the lower side of the barrel, run through the rollers and are engaged in suitable seats of the shaft. These bands are, therefore, longer than the traditional ones and, consequently, with equal force applied by the diver, the roller speargun has a longer range. Thanks to the particular geometry of the new muzzle, one of the …
Bending test for capturing the fractional visco-elastic parameters: theoretical and experimental investigation on giant reeds
2014
In this paper attention is devoted on searching a proper model for characterizing the behavior of giant reeds. To aim at this, firstly, meticulous experimental tests have been performed in the Laboratory of structural materials of University of Palermo. Further, the novel aspect of this paper is that of using an advanced Euler-Bernoulli model to fit experimental data of bending tests. Such a model of continuum beam takes into account different constitutive laws of visco-elasticity, being real materials visco-elastic.
Interaction between Longitudinal Shear and Transverse Bending in Prestressed Concrete Box Girders
2017
In box girder bridges, the quantity and distribution of reinforcement to be put in concrete elements of sections can be evaluated only by considering the deformation of the cross section in addition to the longitudinal analysis of the static scheme, establishing the entire state of stress of box sections. This leads to a need to evaluate the interaction between internal forces obtained by the global analysis and the ones obtained by the local analysis of the cross sections. The frame effect implies the elastic deformation of slabs and webs, whereas eccentrically applied loads lead to cross-section distortion with the loss of the box shape. Hence, the reinforcement is strongly influenced by …
Numerical prediction of the shear response of semi-prefabricated steel-concrete trussed beams
2016
Abstract In this study, the shear behavior of hybrid steel-trussed-concrete beams (HSTCBs) realized with prefabricated steel trusses embedded into a concrete core cast in situ, is investigated by means of Finite Element (FE) numerical simulations. HSTCBs do not behave as classical RC elements nor composite beams. Up to now, there are not specific design criteria in the building codes and the calculation of this type of beams is conducted by means of design-by-testing procedures. The knowledge of the material behavior as well as the understanding of the interaction between materials in contact is the first requirement for the definition of proper design procedures and calculation methods for…