Search results for "Biocomposites"
showing 10 items of 34 documents
Structure and performance properties of environmentally-friendly biocomposites based on poly(ɛ-caprolactone) modified with copper slag and shale dril…
2018
The potential application of two types of industrial wastes, drill cuttings (DC) and copper slag (CS), as silica-rich modifiers of poly(ɛ-caprolactone) (PCL) was investigated. Chemical structure and physical properties of DC and CS fillers were characterized using X-ray diffractometer, X-ray fluorescence spectroscopy, particle size and density measurements. PCL/DC and PCL/CS composites with a variable content of filler (5 to 50 parts by weight) were prepared by melt compounding in an internal mixer. It was observed that lower particle size of DC filler enhanced processing of biocomposites comparing to CS filler. Smaller particles of DC filler and thus the higher specific surface area, enabl…
Biodegradation in soil effects on PLA/sisal and PHBV/sisal biocomposites
2013
The use of bio-based composites like lignocellulosic fibres/polymer composites as an alternative materials are continuously increasing in several applications such as automobile manufacturing, packaging, construction or household and agricultural equipments. In order to warranty the durability on green biocomposites based on polymer matrixes like poly(hydroxy butyrate-co-valerate) (PHBV) and poly(lactide) (PLA), the previous knowledge about the influence of the ambient agents on their macromolecular properties is necessary. In this sense, biodegradation in soil normalised experiments are useful. In this work, two commercial PHBV and PLA were reinforced with sisal fibres at 10 %, 20% and 30%…
Basalt Fiber Hybridization Effects on High-Performance Sisal-Reinforced Biocomposites
2022
The increasing attention given to environmental protection, largely through specific regulations on environmental impact and the recycling of materials, has led to a considerable interest of researchers in biocomposites, materials consisting of bio-based or green polymer matrixes reinforced by natural fibers. Among the various reinforcing natural fibers, sisal fibers are particularly promising for their good mechanical properties, low specific weight and wide availability on the current market. As proven in literature by various authors, the hybridization of biocomposites by synthetical fibers or different natural fibers can lead to an interesting improvement of the mechanical properties or…
New Polylactic Acid Composites Reinforced with Artichoke Fibers
2015
In this work, artichoke fibers were used for the first time to prepare poly(lactic acid) (PLA)-based biocomposites. In particular, two PLA/artichoke composites with the same fiber loading (10% w/w) were prepared by the film-stacking method: the first one (UNID) reinforced with unidirectional long artichoke fibers, the second one (RANDOM) reinforced by randomly-oriented long artichoke fibers. Both composites were mechanically characterized in tensile mode by quasi-static and dynamic mechanical tests. The morphology of the fracture surfaces was analyzed through scanning electron microscopy (SEM). Moreover, a theoretical model, i.e., Hill's method, was used to fit the experimental Young's modu…
Green Composites Based on Hedysarum coronarium with Outstanding FDM Printability and Mechanical Performance
2022
The addition of natural scraps to biodegradable polymers has gained particular interest in recent years, allowing reducing environmental pollution related to traditional plastic. In this work, new composites were fabricated by adding 10% or 20% of Hedysarum coronarium (HC) flour to Poly (lactic acid) (PLA). The two formulations were first produced by twin screw extrusion and the obtained filaments were then employed for the fabrication of composites, either for compression molding (CM) or by fused deposition modeling (FDM), and characterized from a morphological and mechanical point of view. Through FDM it was possible to achieve dense structures with good wettability of the filler that, on…
Strength of cellulosic fiber/starch acetate composites with variable fiber and plasticizer content
2014
In this experimental study, the performance of injection-molded short flax and hemp fibers in plasticized starch acetate were analyzed in terms of strength. Parameters involved in the analysis are a variable fiber and plasticizer content. The measured strength of the composites varies in the range of 12–51 MPa for flax fibers and 11–42 MPa for hemp fibers, which is significantly higher than the properties of the unreinforced starch acetate matrix. The micro-structural parameters used in modeling of composite strength were obtained from optical observations and indirect measurements. Some of these parameters were qualitatively verified by X-ray microtomography.
Biochar Particles Obtained from Agricultural Carob Waste as a Suitable Filler for Sustainable Biocomposite Formulations
2022
In the context of sustainable and circular economy, the recovery of biowaste for sustainable biocomposites formulation is a challenging issue. The aim of this work is to give a new life to agricultural carob waste after glucose extraction carried out by a local factory for carob candy production. A pyrolysis process was carried out on bio-waste to produce biofuel and, later, the solid residual fraction of pyrolysis process was used as interesting filler for biocomposites production. In this work, biochar particles (BC) as a pyrolysis product, after fuels recovery of organic biowaste, specifically, pyrolyzed carobs after glucose extraction, were added on poly(butylene-adipate-co-terephthalat…
Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling
2022
In this work, an innovative green composite was produced by adding Hedysarum coronarium (HC) flour to a starch-based biodegradable polymer (Mater-Bi®, MB). The flour was obtained by grinding together stems, leaves and flowers and subsequently sieving it, selecting a fraction from 75 μm to 300 μm. Four formulations have been produced by compression molding (CM) and fused deposition modeling (FDM) by adding 5%, 10%, 15% and 20% of HC to MB. The influence of filler content on the processability was tested, and rheological, morphological and mechanical properties of composites were also assessed. Through CM, it was possible to obtain easily homogeneous samples with all filler amounts.…
Exploiting the Redox Activity of MIL-100(Fe) Carrier Enables Prolonged Carvacrol Antimicrobial Activity
2022
The design of efficient food contact materials that maintain optimal levels of food safety is of paramount relevance to reduce the increasing number of foodborne illnesses. In this work, we develop a smart composite metal-organic framework (MOF)-based material that fosters a unique prolonged antibacterial activity. The composite is obtained by entrapping a natural food preserving molecule, carvacrol, into a mesoporous MIL-100(Fe) material following a direct and biocompatible impregnation method, and obtaining particularly high payloads. By exploiting the intrinsic redox nature of the MIL-100(Fe) material, it is possible to achieve a prolonged activity against Escherichia coli and Listeria i…
Conifer needles as thermoplastic composite fillers: structure and properties
2016
This study describes the properties of thermoplastic polymer composites based on polyethylene (of low and high density) and ethylene-propylene copolymers using various types of conifer needles (pine, spruce, fir, and cedar) as fillers. For the needles, thermogravimetric analysis (TGA) and TGA/Fourier transform infrared spectroscopy (TGA/FTIR) were performed to investigate their structures and thermal resistance, as required for the composite processing methods. Moreover, structural differences were studied for the analyzed fillers and composite materials (FTIR). The results were compared with the values obtained for composites with conifer wood flour. Composites with conifer needles (pine) …