Search results for "Building"
showing 10 items of 1985 documents
Transient Modelling of Thermal Conditions in Test Buildings Including Radiation
2015
Abstract To increase the energy efficiency of buildings in Latvia's climate a comparative study with five experimental test buildings have been set up in Riga, Latvia. Different thermo physical quantities such as temperature, humidity, air velocity, etc. were monitored to better understand different behaviour of the building envelope. This gives an excellent validation possibility for the CFD model that in future could predict conditions in buildings with different envelopes. Previously a stationary model and transient model were considered without taking into consideration the thermal radiation. This study continues the previous work that was done and proposes a transient model which takes…
Conceptual design of prestressed slab bridges through one-way flexural load balancing
2013
In this paper a study on prestressed concrete slab bridges is presented. A design philosophy based on the concept of load balancing through prestressing is proposed in order to minimize the effects of delayed deformations due to creep. Aspects related to the stress redistribution inside these bridges for time-dependent phenomena are analyzed and discussed, by applying the principles of aging linear visco-elasticity. Prestressing is seen as an equivalent external load which counterbalances the permanent loads applied to the bridge, nullifying the elastic deflections due to sustained loads, and thus avoiding the related delayed deformations. An optimization of the structural behavior through …
Serviceability and Ultimate Safety Checks of SegmentalConcrete Bridges through N-M and M-V Interaction Domains
2015
In current engineering practice, safety checks on serviceability and determinations of ultimate limit states of segmental bridges built by cantilevering are generally performed, either considering separately the contributions of axial force N, bending moment M, and shear force V, or considering the interaction effects through approximate expressions supplied by building codes. During construction stages and service life, the interaction between internal forces can be of fundamental importance in establishing the actual degree of structural safety and, for this reason, a different philosophy for performing checks in segmental bridges is proposed in this paper, plotting N-M and M-V interactio…
Simplified model for compressive response of RC column footing with square cross-section
2017
Abstract In this paper, a simplified calculus model for the prediction of the compressive response of RC column footing with a square cross-section is presented. As it is well-known RC concrete footing are designed adopting uniform contact pressures on the substrate and assuming a strut and tie model in deep members and a cantilever beam or slab model in flexible members. Deep and flexible members are distinguished in literature only based on the tangent of the angle expressed as the ratio between the depth and the shear span of the footing. In this paper, several subgrade contact pressures distribution for column footings (rigid or soft soils) were considered in developing a mechanical mod…
Partial Elastic Scheme Method in Cantilever Construction of Concrete Arch Bridges
2013
AbstractIn this paper, a study about stay stressing procedures of concrete arch bridges built by cantilevering with temporary stays is presented. Particularly, the partial elastic scheme method is proposed to find the initial cable forces, and a forward procedure is implemented to follow the actual sequence of construction by extending a procedure already applied to concrete cable–stayed bridges. The theoretical treatment is followed by a numerical application on a case study of a concrete arch bridge, and a comparison between initial cable forces found by the partial elastic scheme method and classical backward analysis is presented here. Results show the effectiveness of the proposed proc…
The influence of time-dependent phenomena in segmental construction of concrete cable-stayed bridges
2011
Construction stages of a cable-stayed bridge are characterized by a sequence in which geometric configuration, restraints and consequently stress and strain patterns vary many times till the final arrangement is achieved. When construction of concrete bridges is made by cantilever method the influence of time-dependent phenomena becomes significant. In this study an evaluation of stay stressing procedures is given by taking into account creep and shrinkage in cantilever construction of concrete cable-stayed bridges. A methodology of stay stressing is proposed with the final target of reaching the desired geometric configuration. Comparison with classical analyses performed by backward metho…
Definition of Seismic Vulnerability Maps for Civil Protection Systems: The Case of Lampedusa Island
2016
The opportunity to locate and quantify the major criticalities associated to natural catastrophic events on a territory allows to plan adequate strategies and interventions by civil protection bodies involved in local and international emergencies. Seismic risk depends, most of all, on the vulnerability of buildings belonging to the urban areas. For this reason, the definition, by a deep analysis of the territory, of instruments identifying and locating vulnerability, largely favours the activities of institutions appointed to safeguard the safety of citizens. This paper proposes a procedure for the definition of vulnerability maps in terms of vulnerability indexes and critical peak ground …
User Activity Recognition for Energy Saving in Smart Homes
2015
Abstract Energy demand in typical home environments accounts for a significant fraction of the overall consumption in industrialized countries. In such context, the heterogeneity of the involved devices, and the non negligible influence of the human factor make the optimization of energy use a challenging task; effective automated approaches must take into account basic information about users, such as the prediction of their course of actions. Our proposal consists in learning customized structural models for common user activities for predicting the trend of energy consumption; the approach aims to lower energy demand in the proximity of predicted peak loads so as to keep the overall cons…
Review of push-out and shear response of hybrid steel-trussed concrete beams
2018
The hybrid steel trussed concrete beams examined in the present study are comprised of two principal components, i.e., a steel joist with inclined rebars, realized in industry, which is welded to a smooth steel plate and then embedded within the concrete cast in situ. The paper presents first the state of the art on laboratory tests and analytical modeling of the steel-to-concrete stress transfer mechanism investigated by push-out tests. Next, the most relevant scientific contributions currently available in the technical literature regarding experimental investigation on actual shear behavior are summarized and discussed. Lastly codes and analytical models are reviewed.
Validation of a Shear Model for RC and Hybrid Beams with Two Different Inclinations of Transversal Reinforcement
2016
The validation of an analytical model recently proposed for evaluation of the shear capacity in Reinforced Concrete (RC) beams containing multiple inclination of transverse stirrups is presented. The model is a suitable extension of that currently proposed in Eurocode 2 for the evaluation of the shear resistance, and it is derived by means of the the variable-inclination stress-field theory based on Nielsen’s plastic approach. Experimental and numerical data available in the literature on Hybrid Steel-Trussed Concrete Beams (HSTCBs) are used for model validation and result discussion. Finally, also the comparison with a different analytical approach for the assessment of the shear resistanc…