Search results for "C.C."
showing 10 items of 54981 documents
An exact method for the determination of differential leakage factors in electrical machines with non-symmetrical windings
2016
An exact and simple method for the determination of differential leakage factors in polyphase ac electrical machines with non-symmetrical windings is presented in this paper. The method relies on the properties of Gorges polygons that are used to transform an infinite series expressing the differential leakage factor into a finite sum in order to significantly simplify the calculations. Some examples are shown and discussed in order to practically demonstrate the effectiveness of the proposed method.
Formation of dislocations and hardening of LiF under high-dose irradiation with 5–21 MeV 12C ions
2017
R. Zabels, I. Manika, J. Maniks, and R.Grants acknowledge the national project IMIS2, and A. Dauletbekova, M. Baizhumanov, and M. Zdorovets the Ministry of Education and Science of the Republic of Kazakhstan for the financial support.
High-Power Multicarrier Generation for RF Breakdown Testing
2017
Testing of satellite components for high RF power breakdown effects, such as multipactor and corona or passive-intermodulation, is a topic of growing interest in the aerospaceindustry. Switching fromthe classical single carrier approach to the more realisticmulticarrier scenario is very challenging from the experimental point of view. Themulticarrier signals, amplifiedby several RF power amplifiers, need to have controlled phase, amplitude, and frequency in each carrier. Fine tuning of the signal generator phases is required in order to compensate the phase drift occurring in the active elements of the test bed. This paper presents an efficient and low-cost technique to generate multicarrie…
Identification of induction motor thermal model for improved drivetrain design
2016
Selection of components of electric drivetrains is not only based on evaluating their ability to perform according to mechanical specifications, but — what is equally important — on assessing their thermal protection limits. These are typically affected by electrical and thermal properties of motors and drives. Although rated parameters (such as power, torque, speed, etc.) are easily accessible in catalogs of equipment producers, more specific properties like mass / length of copper winding, heat dissipation factor, rotor / stator dimensions etc. are not available to customers. Therefore, effective selection of drivetrain components is limited due to the lack of sufficient data and the need…
Coeval Cold Spray Additive Manufacturing Variances and Innovative Contributions
2017
Tremendous attention has been given to the cold spray process, even more today with the emergence of additive manufacturing, worldwide. Several inventions related to the cold spray technology have been patented for over a century and mostly since a couple of decades. But the cold spray technology knows a period of great innovations due to recent and current substantial explorations. Various technological solutions have been developed. The technical dimension, and particularly in terms of manufacturing method, has also always been a major genesis of progresses and novelties. This chapter is a technological survey of the cold spray additive manufacturing and reports variant methods and innova…
High-frequency electrodeless lamps in argon–mercury mixtures
2005
In this paper, numerical and experimental investigations of high-frequency (HF) electrodeless lamps in argon–mercury mixtures are performed. The intensities of the mercury spectral lines having wavelengths λ = 404.66, 435.83, 546.07 nm (7 3S1–6 3P0,1,2) and the resonance line λ = 253.7 nm (6 3 P1–6 1S0) are measured at a wide range of mercury pressures, varying the HF generator current and argon filling pressure. A stationary self-consistent model of HF electrodeless discharge lamp is developed including kinetics of the excited mercury and argon atomic states. Based on the developed model, the radiation characteristics of the discharge plasma are calculated. Numerical simulation of the line…
Evolution of application-specific cache mappings
2020
Reconfigurable caches offer an intriguing opportunity to tailor cache behavior to applications for better run-times and energy consumptions. While one may adapt structural cache parameters such as cache and block sizes, we adapt the memory-address-to-cache-index mapping function to the needs of an application. Using a LEON3 embedded multi-core processor with reconfigurable cache mappings, a metaheuristic search procedure, and MiBench applications, we show in this work how to accurately compare non-deterministic performances of applications and how to use this information to implement an optimization procedure that evolves application-specific cache mappings for the LEON3 multi-core processo…
Production of Nano-Sized Co<sub>3</sub>O<sub>4</sub> by Pyrolysis of Organic Extracts
2016
The most promising application field of materials based on nano-sized Co3O4 is catalysis. The method of production is one of the factors, which greatly affects the catalytic activity of Co3O4 catalysts. The aim of this research is to study possibilities of a new promising extractive-pyrolytic method (EPM) for the production of Co3O4 nanopowders and silica- and ceria-supported Co3O4 nanocomposites. Solutions of cobalt hexanoate in hexanoic acid and trioctylammonium tetrachlorocobaltate in toluene preliminary produced by solvent extraction were used as precursors. The precursors’ thermal stability, phase composition, morphology and the magnetic properties of the final products of pyrolysis we…
Determination of Core Size Dependency on the EMI Suppression in Cable Ferrites
2020
Electromagnetic Compatibility (EMC) engineering should be approached via the systems approach, considering EMC throughout the design to anticipate possible electromagnetic interferences (EMI) problems. Nevertheless, an EMI source may appear when the designed device is supplied via an external power system or it is connected to another device to communicate to it. In these both cases, the cables or interfaces that interconnect the systems could represent the EMI source. Thereby, one of the most common techniques for reducing EMI in cables is the application of an EMI suppressor such as sleeve ferrite cores to them. The advantage of this solution is that it does not involve redesign the elect…
The helicoidal magnetic generator
2016
Recently helicoidal generator for the exploitation of sea wave energy has been proposed. This device can convert both the vertical and rotational movement of seawaves. The electrical energy generated by such a device must be converted and conditioned in order to match the instantaneous utility requirements and a power link from the sea to an interconnection is needed. In this paper, the authors propose a mathematical model of this device and preliminarily present a prototype of the machine.