Search results for "CERAMICS"
showing 10 items of 1599 documents
Strengthening of steel-reinforced concrete structural elements by externally bonded FRP sheets and evaluation of their load carrying capacity
2014
Abstract The paper proposes a preliminary design tool for reinforced concrete (RC) elements strengthened by fiber-reinforced-polymer (FRP) sheets to be used in civil engineering applications and in particular in medical buildings. The design strategy is based on limit analysis theory and utilizes a numerical procedure which provides a direct method to determine peak load, failure mode and critical zones of the structural elements of interest.
Thermo-mechanical post-buckling analysis of variable angle tow composite plate assemblies
2017
peer-reviewed The increasing use of composite materials for lightweight structural applications and the extended tailoring capabilities offered by variable stiffness laminates requires rapid and robust analysis tools that adequately describe the mechanical behaviour of such structures. In this work, a Rayleigh–Ritz solution for generally restrained multilayered stiffened variable angle tow plates in the post-buckling regime is presented. The plate model is based on first-order shear deformation theory and accounts for geometrical nonlinearity through von Kármán’s assumptions. General symmetric and unsymmetric stacking sequences are considered and Legendre orthogonal polynomials are employed…
Material characteristics in the analysis of heated steel beams
1989
Beam fire tests are expensive and complicated. They may be replaced by calculations of the heated beam deflection by means of the method presented in this paper. The following material characteristics in the analysis of the deflection of beams during fire may be taken as fundamental: the steel creep characteristic at elevated temperatures, the modulus of elasticity and the coefficient of thermal expansion. According to the yield hinge theory, the yield stress is the criterion of failure of steel beams in fire. On the other hand, in the analysis of the deflection of the heated steel beams the influence of the yield stress is very small. The influence of the respective material characteristic…
Shape and dimensional accuracy in Single Point Incremental Forming: State of the art and future trends
2007
Abstract The paper is aimed to discuss some relevant issues concerning an innovative sheet metal forming technology, namely Single Point Incremental Forming. The advantages of this technology are addressed, including its capability to provide effective answers to some impellent industrial requirements: process flexibility, strong customer orientation, production of highly differentiated goods at low industrial costs. As well some relevant drawbacks are highlighted, mainly as concerns the level of accuracy permitted by the process. A wide recognition of the research efforts in this field is presented, taking into account some general considerations on the difference sources of shape and dime…
Optimization of the contact surface shape of a shrinkage fit
1998
Amongst many processes existing today for the assembly of two cylindrical parts, the shrinkage fit is commonly used. However, in the calculation methods, the contact surfaces are assumed to be perfect. Therefore, in order to apply these, the standards necessitate very small geometrical tolerances. The objective of the present paper is to show that it is possible to take into account form defects by closely conformed contact modelling and to have a good representation of reality: form defects always exist to an increasing extent and are inherent in all kinds of manufacturing processes. Finally, it is shown that the presence of defects can be beneficial, allowing optimization from both a mech…
Numerical and experimental verification of new method for connecting pipe to flange by cold forming
2015
Abstract In this paper a new method of connecting pipe to flange without welding is presented. This method is a cold forming process that is based on plastic expansion/deformation of the pipe into a modified standard flange by use of a cold forming tool. The method is patented by Quickflange Technology AS and represents a highly feasible alternative to welding. The successful use of the method requires the ability to predict dimensional and stress/strain characteristics of the pipe and flange after the connection process in order to evaluate the connectivity to the adjacent flange as well as the leak tightness. In addition the ability to predict the process force during the connection proce…
The evaluation of springback in 3D stamping and coining processes
1998
Abstract An effective predictive technique of the elastic springback in a fully 3D 90° V-punch V-die bending process is presented. This is based on a combined approach in which an explicit finite element code was used to simulate the loading phase of the process whilst an implicit procedure was used to analyse the springback phase. Two different punches with a nose radius of 4 and 8 mm were used. An increase in the springback ratio with the coining load was observed with the lower nose radius. Conversely, an increase in the springback ratio with the coining load up to a peak value (>1), corresponding to a force of about 20 kN, followed by a decrease in the springback ratio with increasing t…
Composite Material Recycling Technology—State-of-the-Art and Sustainable Development for the 2020s
2021
Recently, significant events took place that added immensely to the sociotechnical pressure for developing sustainable composite recycling solutions, namely (1) a ban on composite landfilling in Germany in 2009, (2) the first major wave of composite wind turbines reaching their End-of-Life (EoL) and being decommissioned in 2019–2020, (3) the acceleration of aircraft decommissioning due to the COVID-19 pandemic, and (4) the increase of composites in mass production cars, thanks to the development of high volume technologies based on thermoplastic composites. Such sociotechnical pressure will only grow in the upcoming decade of 2020s as other countries are to follow Germany by limiting and ba…
XRD microstructural analysis of mullites obtained from kaolinite–alumina mixtures
2000
Abstract A microstructural study of mullite obtained by the reaction sintering of kaolinite–α–alumina mixtures in the range 1150–1700°C has been performed by using X-ray line profile analyses together with scanning and transmission electron microscopy equipped with microanalysis by energy dispersion (SEM-EDS, TEM-AEM). Two kinds of morphology corresponding to primary (elongated grains) and secondary (equiaxed grains) mullite have been observed. A bimodal crystallite size distribution has been detected through XRD microstructural analysis from 1300°C. The results obtained by this method are compared with SEM/TEM data.
Conformational polymorphs of 1,1,2,2-tetrachloroethane: pressure vs. temperature.
2011
Directional Cl···Cl type I and II interactions govern the low-density aggregation of 1,1,2,2-tetrachloroethane molecules in synclinal conformation in the crystalline state at low temperature, whereas the dense molecular packing in high-pressure is achieved for the antiperiplanar conformers and electrostatically less favored Cl···Cl contacts. The mechanism of transformation between loose and dense associations involves the collapse of Cl···Cl contacts and conformational conversion.