Search results for "CIRCUIT"
showing 10 items of 936 documents
Efficient pipeline FFT processors for WLAN MIMO-OFDM systems
2005
The most area-efficient pipeline FFT processors for WLAN MIMO-OFDM systems are presented. It is shown that although the R2/sup 3/SDF architecture is the most area-efficient approach for implementing pipeline FFT processors, RrMDC architectures are more efficient in MIMO-OFDM systems when more than three channels are used.
Low-Power Design of Delay Interpolating VCO
2008
In this paper, a design methodology for low-power MCML based delay interpolating VCOs is presented. The methodology allows a fast and accurate graphical evaluation of the optimum design. It utilizes two closed form expressions for the upper and lower oscillation frequencies of the VCO. An expression of the tuning range is also derived. The effectiveness of the proposed design methodology has been tested by simulating several VCOs in an IBM 0.13 mum CMOS technology.
Phasor total unbalance power: Formulation and some properties
2007
Unbalance power has been used to quantify unbalance phenomenon effects in the electric power systems for a long time. Expressions of this power developed by some different theories only give the value of its module. Therefore, total unbalance power values in electric power systems cannot be obtained by the unbalance power values of each of their loads. For that, it is necessary to express the unbalance power as a complex number. In this paper the unbalance power is expressed in phasor notation and some of their properties are described, applied to electric systems with balanced voltages. Results are verified by simulation and also practical comparative experiences are realized in actual ins…
Reconfiguration Techniques of Partial Shaded PV Systems for the Maximization of Electrical Energy Production
2007
In this paper, the research of the optimal layout of photovoltaic (PV) modules in a PV array giving the maximum output power under different shaded working conditions is carried out. The particular condition of non uniform solar exposition of the modules is analyzed. The study of the different configurations has been carried out starting from a circuital model used for the design of PV cells and for the simulation of the working behavior of PV arrays. The attained results appear to be interesting although the complexity of the problem in mathematical terms is huge when the number of panels is high. Moreover, the results confirm that this approach often allows to attain a higher electrical e…
Higher PV Module Efficiency by a Novel CBS Bypass
2011
There is an increasing focus on reducing costs and improving efficiency for photovoltaic (PV) cells and modules as well as finding a more efficient approach to the product manufacturing. This letter introduces an innovative solution to bypass shaded PV cells instead of a traditional Schottky diode, in order to avoid overheating of cells in the case of partial shading. The goal is to reduce the power dissipation and improve the general efficiency of a PV generator. A novel device called cool bypass switch is then presented. It is made up of a Power MOS driven by a controller with the task to charge a storage capacitor. Tests and comparisons with standard Schottky diodes are then performed an…
Optimized Topology for High Efficiency Battery Discharge Regulator
2008
In the following years power levels of 20 kW to 50 kW will be demanded by the telecommunication satellites. It is not possible to keep 0.5 kW modules with up to 100 modules in parallel and, therefore, higher power modules must be used. A higher bus voltage seems also necessary and any voltage below 150 V and above 100 V could meet the needs. In addition, new optimized topologies that process only a part of the total power delivery can be employed to improve the efficiency. In this article, design guidelines and experimental results of a high efficiency battery discharge regulator (BDR) module based on parallel power processing are given.
Uncertainty evaluation of a Backward/Forward Load Flow algorithm for a MV smart grid
2015
This paper presents the uncertainty evaluation of an innovative measurement algorithm for load flow analysis in MV distribution networks. The measurement procedure is based on Low Voltage (LV) load power measurements applied on a Backward/Forward (B/F) algorithm for the Load Flow (LF) resolution. Furthermore, in the procedure a three phase voltage measurement at the MV generating substation bus-bars is also considered. The accuracy analysis of the LF algorithm is performed in the case of a real load condition in the distribution grid of Ustica island, Italy. The analysis takes into account the uncertainty of the measurement instruments at the LV side of each secondary substation power trans…
A suitable control technique for fault-tolerant converters in Distributed Generation
2011
The penetration of Distributed Generation (DG) in power systems is deeply changing the existing distribution networks which is becoming a very sophisticated and complex systems incorporating both active (generators) and passive systems (distribution systems, converters and loads). The necessary simplification can be obtained dealing with small networks, namely Micro-Grids, reproducing, in a smaller scale, the structure and the problems of large networks including production, transmission and distribution of the electrical energy. In order to achieve an adequate level of reliability, fault-tolerant operations of micro-grids become very important. This result can be achieved only using power …
COMPARATIVE ANALYSIS OF RIGID AND FLEXIBLE STRUCTURES OF THE ECCENTRIC PRESSES
2007
Abstract The aim of this paper is to make a comparative study of the static behaviour of the eccentric presses, using the finite elements method, on the rigid structure and on the flexible structure, respectively. The finite elements modelling of the component elements of the presses are done in two ways: node by node link type (rigid structure) or using a linking element spring damper type (flexible structure). On these two structures there is successively applied a number of static analyses, in order to determine the strain of working area and the design of the stiffness graph.
Experimental study of low-voltage surge protection device response in realistic systems
2008
Experimental results on low-voltage surge protection under fast pulses in realistic wiring systems are presented. A fast voltage pulse generator is designed to provide fast voltage pulses with short steep fronts. The effective residual voltage of protected equipment is then investigated and compared with simulation results.