Search results for "COMPOSITE"
showing 10 items of 4584 documents
Surface and mechanical characterization of stationary shoulder friction stir welded lap joints: experimental and numerical approach
2020
Friction Stir Welding (FSW) is one of the most used solid-state welding processes in the aeronautical, aerospace, ground transportation and naval fields. Stationary Shoulder Friction Stir Welding (SSFSW) is a recently introduced variant of the process allowing lower heat input into the joints, with beneficial effects in terms of joint mechanical properties, microstructure and top surface finish. In the paper, lap joints produced by SSFSW and made out of AA6082-T6 aluminum alloy sheets have been analyzed with the aim to investigate the effect of the stationary shoulder on the lap joints surface, metallurgical, and mechanical properties. The lap joints produced by SSFSW have been compared to …
Influence of friction stir processing conditions on the manufacturing of Al-Mg-Zn-Cu alloy/boron carbide surface composite
2018
Abstract Surface metal matrix composites were synthesized via friction stir processing (FSP) on the surface of aluminium alloy 7075 (AA 7075) sheets by incorporating B4C particles (B4CP). The influence of tool rotational speeds, powder particle sizes, and change in tool travel direction between FSP passes on particle distribution and resulting properties were studied in detail. Change in tool travel direction, decreased tool rotation speed and fine B4C particles enhanced B4CP distribution and wear properties thereof. Wear resistance of composites were doubled on account of the B4CP distribution and resultant several strengthening mechanisms.
Enhancement of mechanical properties of FSWed AA7075 lap joints through in-situ fabrication of MMC
2017
Abstract Friction Stir Processing (FSP) has been demonstrated feasible to create local Metal Matrix Composites (MMCs) in light alloys matrix. In this research, local MMCs were produced contextually to the weld using Friction Stir Welding (FSW). SiC particles were added to AA7075 lap joints by creating a proper groove on the top surface of the bottom sheet. Different welds were produced with increasing number of tool passes. The effect of the multiple passes was investigated through shear tests, macro and micro observations, average grain size and microhardness measurements. The welded joints were compared to a reference weld produced with no reinforcements. It was found that poor mixing bet…
A macroscale FEM-based approach for selective laser sintering of thermoplastics
2017
A numerical approach to model the selective laser sintering (SLS) of polypropylene is proposed. A 3D thermal model was developed and thus enables the prediction of the temperature fields and the extension of the sintered area in the powder bed taking into account the phase change during multiple laser passes. Powderâliquid, liquidâsolid and solidâliquid phase changes were modelled during the SLS and the subsequent cooling processes. Then, a 3D thermomechanically coupled model was set up based on the temperature results of the thermal model in order to predict the distortion of the produced parts after cooling down. Different pre-heating temperatures were considered, highlighting their…
An Additive Model to Predict the Rheological and Mechanical Properties of Polypropylene Blends Made by Virgin and Reprocessed Components
2021
In this work, an additive model for the prediction of the rheological and mechanical properties of monopolymer blends made by virgin and reprocessed components is proposed. A polypropylene sample has been reprocessed more times in an extruder and monopolymer blends have been prepared by simulating an industrial process. The scraps are exposed to regrinding and are melt reprocessed before mixing with the virgin polymer. The reprocessed polymer is, then, subjected to some thermomechanical degradation. Rheological and mechanical experimental data have been compared with the theoretical predictions. The results obtained showed that the values of this simple additive model are a very good fit fo…
The application of the random balance method in laser machining of metals
2008
International audience; Features peculiar to laser technology offer some advantages over more traditional processes, but, like all processes, it has its limitations. This article studies the limitations of laser machining of metals, and quantifies, through an experimental design method, the influence of operating parameters on productivity and on the quality of the machined surface. Three study materials were used: an aluminium alloy, stainless steel and a titanium alloy. An initial reading of the results indicates that productivity depends mainly on the frequency of the laser pulse and that the aluminium alloy behaves differently from the other two. The quality of the machined surface, jud…
A numerical model for Wire integrity prediction in Friction Stir Extrusion of magnesium alloys
2017
Abstract A numerical model for the prediction of the wire quality produced by the novel direct machining chip recycling technique known as Friction Stir Extrusion (FSE) is presented. Wire microstructure and wire integrity have been predicted by embedding in the code the equations enabling the calculation of the Zener-Hollomon parameter as well as the W parameter of the Pivnik-Plata solid bonding criterion. The proposed model, developed for the AZ31 magnesium alloy using the commercial simulation package DEFORM, is 3D Lagrangian, thermo-mechanically coupled with visco-plastic material behavior. The model was first validated against experimental temperature measurements and then used to predi…
Influence of processing parameters and initial temper on Friction Stir Extrusion of 2050 aluminum alloy
2017
Abstract Friction Stir Extrusion is an innovative production technology that enables direct wire production via consolidation and extrusion of metal chips or solid billets. During the process, a rotating die is plunged into a cylindrical chamber containing the material to be extruded. The stirring action of the tool produces plastic flow in the extrusion chamber, densifying and heating the charge so that finally, fully dense rods are extruded. Experiments have been carried out in order to investigate the influence of process parameters and initial temper of the base material on the process variables and on the extrudates’ mechanical properties.
Axial Load Capacity of Cold Formed Pipe Flange Connection
2017
In this paper, a cold forming process is used where the connection between a pipe and a flange is created by means of radially expanding tool segments inside the pipe. The method is investigated with two purposes, to set up a robust procedure for the process that allows for connections to be made on site, and to set up finite element (FE) simulations that can capture the forces and deformations when pulling the pipe axially out of the flange. Experimental data and FE simulations are used to describe and understand the forces and deformations during the connection process. The rapid increase in radial stiffness experienced when the pipe comes in full circumferential contact with the flange i…
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…