Search results for "COMPOSITE"

Influence of the Resin Layer Thickness at the Interface of Hybrid Metal-composite Co-cured Joints

2011

As discussed in literature, the accurate analysis of the modern co-cured joints between composite materials or between a metal and a composite material (hybrid joints) is complicated by the influence of the interface resin layer on the interface singular stress field. In such joints, in fact, there is not a proper adhesive layer and the thickness of the resin layer, that plays the role of the adhesive, is not constant due to the presence of the reinforcing fibers in the composite adherent. For this reason several authors assume that a generic co-cured joint can not be studied as a simple bi-material joint, without considering the particular characteristics of the actual resin layer. This pr…

Experimental Investigation on Stiffness and Strength of Single-Lap Z-Pinned Joints in a Laminated CFRP Stress-Ribbon Strip

2016

Carbon fiber-reinforced polymer (carbon-polymer) is an advanced lightweight composite material with high strength and excellent resistance to corrosion and fatigue. Over the past decades, application of fiber-reinforced polymers has been spread from the aerospace to other branches of industry such as automobile and civil engineering. Unidirectional carbon-polymers have a high potential for replacing steel in tensile members. Recently, the first carbonpolymer stress-ribbon bridge has been constructed in Germany. The non-laminated strip-loop carbon-polymer thin strips were used as the load bearing components in this bridge. In comparison with the laminated components, the applied cables are c…

Considering lithium-ion battery 3D-printing via thermoplastic material extrusion and polymer powder bed fusion

2021

In this paper, the ability to 3D print lithium-ion batteries through thermoplastic material extrusion and polymer powder bed fusion is considered. Focused on the formulation of positive electrodes composed of polypropylene, LiFePO4 as active material, and conductive additives, advantages and drawbacks of both additive manufacturing technologies, are thoroughly discussed from the electrochemical, electrical, morphological and mechanical perspectives. Based on these preliminary results, strategies to further optimize the electrochemical performances are proposed. Through a comprehensive modeling study, the enhanced electrochemical suitability at high current densities of various complex three…

Clinical Behavior of Ceramic, Hybrid and Composite Onlays. A Systematic Review and Meta-Analysis

2020

A systematic review and meta-analysis was performed to analyze the survival of onlay restorations in the posterior region, their clinical behavior according to the material used (ceramic reinforced with lithium disilicate, conventional feldspathic ceramic or reinforced with leucite; hybrid materials and composite), possible complications, and the factors influencing restoration success. The systematic review was based on the preferred reporting items for systematic reviews and meta-analyses (PRISMA) statement, without publication date or language restrictions. An electronic search was made in the PubMed, Scopus, Embase, and Cochrane databases. After discarding duplicate publications and stu…

Structure and Photocatalytic Properties of TiO2-WO3Composites Prepared by Electrophoretic Deposition

2015

In this work TiO2-WO3 composite films containing different oxide concentrations were prepared by electrophoretic deposition on steel substrates. Composite coating structures were analyzed by X -ray diffraction, Raman spectra and scanning electron microscopy. The results showed an even distribution of WO3 particles in the entire composite layer. Light absorption measurements were used for photocatalytic properties evaluation. It was found that the removal ratio of methylene blue depends on the (TiO2):(WO3) concentration ratio. The most effective photodegradation was determined for the sample that was electrophoretically deposited from the suspension with the molar content ratio n(TiO2):n(WO3…

Erratum to ‘Raman spectroscopy of β-irradiated silica glass’ by B. Boizot, S. Agnello, B. Reynard, R. Boscaino and G. Petite [J. Non-Cryst. Solids 32…

2004

COMPOSITE SYNERGY OF SERVICES - A NEW CONCEPT CONCERNING SERVICES

2013

The current paper addresses the dynamics of the service sector in Romania, from the perspective of a new concept, namely the "composite synergy of services". The main points of the paper approach the fact that direct and indirect investments in the service sector create a synergic and composite effect on the development of the economy, as a whole, in Romania. The paper aims to be a prequel to a mathematical and economic demonstration of the existence of the composite synergy of services, laying the theoretical foundations of the concept and underlining the premises for its existence.

An Easy Route Towards Regioselectively Difunctionalized Cyclens and New Cryptands.

2006

Reductive amination of various aldehydes with cyclen represents a very convenient method for the synthesis of a wide range of 1,7-difunctionalized cyclens, as well as new cryptands.

Swelling of cellulose fibres in composite materials: Constraint effects of the surrounding matrix

2013

Swelling of cellulose fibres in composite materials : Constraint effects of the surrounding matrix

Value-added bioproducts or renewable energy derived from lignin? : comparative regional economic and environmental impact assessment : case Metsä Gro…

2016

Metsä Group’s next-generation bioproduct mill in Äänekoski will be operational within Q3/2017 and it will have significant regional economic impact on Central Finland. The mill will operate applying principles of circular economy, and thus utilize all possible side streams from pulp production. Lignin is one of the side streams that has huge potential to be refined, as sustainable products and by creating new value added. Conventionally, lignin is combusted with black liquor to generate energy in pulp mills. This thesis compares this conventional situation to refining lignin into biocomposite products made from 100% renewable resources with regard to regional economic and environmental impa…