Search results for "CREM"
showing 10 items of 224 documents
Measuring of Geometrical Precision of Some parts Obtained by Asymmetric Incremental Forming Process After Trimming
2007
Asymmetric Incremental Forming exalts the advantages of Incremental Forming process since no dies are strictly necessary. In this way complex geometries may be manufactured with a very simple clamping equipment. On the other hand, this characteristic determines some intrinsic drawbacks which penalise its industrial suitability; first of all, the dimensional control of the manufactured part is a still open point for researchers all over the world. Several approaches have been already proposed in the last years to solve the problem, resulting only in partial solutions. At the same time, up to now, the numerical simulation did not supply significant aid to the designers, due to the problem com…
An analytical model for improving precision in single point incremental forming
2007
Abstract In the modern manufacturing scenario and, in particular, in sheet metal forming, the requirement of customised production is still growing. The introduction of incremental forming enables the production of customised components in small lots. In particular, single point incremental forming is characterised by the simplest equipment; any die, in fact, is avoided reducing the necessary tooling to a simple frame, able to clamp the sheet, and a hemispherical punch that imposes the required deformation. This tooling simplicity and the associated process mechanics, in turn, determine a sometimes relevant lack of accuracy. The paper is focused on the investigation of the influence of the …
Adjustable prestressing for construction stages of incrementally launched bridges
2014
Incrementally launched bridges, which are generally built with the static scheme of a continuous beam on supports, change their scheme several times during launching. In these different configurations, internal forces vary and bending moments of opposite signs occur in the same sections for different positions of deck during advancement. In these bridges, two different kinds of prestressing are necessary: a temporary one during launching and a definitive one in service life. In this study, the possibility of implementing automatic adjustable prestressing for the launching stages is investigated; the launch prestressing is partially supplied by a system which can change the tension value in …
A new modified Inc-Cond MPPT technique and its testing in a whole PV simulator under PSC
2015
In this paper a new modified Inc-Cond MPPT technique able to lead PV plants to work in the real MPP (Maximum Power Point) under PSC (Partial Shading Condition) is proposed. The new Inc-Cond MPPT technique working principle is fully explained, discussed and then successfully tested in a whole and reliable PV simulator conceived and set-up by the Authors in order to test and compare several new MPPT algorithms. The simulation results show that the proposed Inc-Cond MPPT technique is able to successfully lead the PV plant to work in the real MPP both in the cases of instantaneous and gradual changing of shading and of temperature conditions.
Incremental dynamic based fragility assessment of reinforced concrete structures: Stationary vs. non-stationary artificial ground motions
2017
Abstract Artificial and natural records are commonly employed by researches and practitioners to perform refined seismic assessments of structures. The techniques for the generation of artificial records and their effectiveness in producing signals which are significantly representative of real earthquakes are still debated as well as results of the consequent seismic assessment to expect from their application. The paper presents an in-depth comparative study highlighting the effect of employing different typologies of artificial ground motion records on seismic assessment results, especially addressing seismic fragility curves. Three sets of 50 stationary, nonstationary evenly modulated a…
A force measuring based strategy for failure prevention in incremental forming
2006
Abstract Incremental forming processes show a number of advantages compared to the traditional processes but, at the same time, some drawbacks are clearly known. Current problems, include the slowness of the process, low accuracy and a lack of knowledge in the field of material formability. This paper is focused on the latter issue: an industrially oriented methodology for detecting the approach of failure in incremental forming is proposed. The approach is based on the analysis of the trend of the forming force in order to assess whether the process can be run safely. If not, a proper strategy, to avoid material failure, is proposed and experimentally validated.
Influence Of Lateral Load Distributions On Pushover Analysis Effectiveness
2008
The effectiveness of two simple load distributions for pushover analysis recently proposed by the authors is investigated through a comparative study, involving static and dynamic analyses of seismic response of eccentrically braced frames. It is shown that in the upper floors only multimodal pushover procedures provide results close to the dynamic profile, while the proposed load patterns are always conservative in the lower floors. They over-estimate the seismic response less than the uniform distribution, representing a reliable alternative to the uniform or more sophisticated adaptive procedures proposed by seismic codes. © 2008 American Institute of Physics.
Shape and dimensional accuracy in Single Point Incremental Forming: State of the art and future trends
2007
Abstract The paper is aimed to discuss some relevant issues concerning an innovative sheet metal forming technology, namely Single Point Incremental Forming. The advantages of this technology are addressed, including its capability to provide effective answers to some impellent industrial requirements: process flexibility, strong customer orientation, production of highly differentiated goods at low industrial costs. As well some relevant drawbacks are highlighted, mainly as concerns the level of accuracy permitted by the process. A wide recognition of the research efforts in this field is presented, taking into account some general considerations on the difference sources of shape and dime…
Deep drawing versus incremental forming processes: A comparative cradle to gate analysis
2012
The evaluation and reduction of the environmental impact of manufacturing processes have become a crucial issue in the last few years, addressing the interest of industrial and academic research towards greener solutions and technologies. Reducing input materials and energy requirements has become an imperative action in the industrial practice. As a matter of fact, strong is the concern on lightweight solutions and technologies for sheet stamping operations especially in the automotive sector. However, the knowledge on how impactful such processes are is still poor. In this paper, a comparison between a traditional deep drawing and an single point incremental forming process is investigate…
Cluster and firm-specific antecedents of organizational innovation
2016
Based on the idea of the tourist destination as a cluster, this paper proposes a model to explain the relationships between exploration and exploitation capabilities – whether originating in the cluster or firm-specific – and a firm’s organizational innovation. This study turns to the resource-based view to provide a theory-based concept of shared capabilities accumulated in a tourist destination or cluster, together with valid measurement instruments to capture them. Our conceptual model highlights the theoretical and practical benefits for firms of being embedded in a cluster to develop both exploration and exploitation capabilities. The study also analyses the interaction between cluster…