Search results for "Chassis"
showing 10 items of 11 documents
Modeling of an active torsion bar automotive suspension for ride comfort and energy analysis in standard road profiles
2019
Abstract Chassis technology is evolving towards active suspension, in which actuators can provide forces to each wheel individually. This overcomes the traditional trade-off between comfort and handling, at the expense of increased complexity and electric consumption. To reduce power demand, regenerative solutions capable of harvesting a certain amount of energy otherwise dissipated in vehicle suspensions and to enhance vehicle dynamics for improving ride comfort and road safety at the same time have been researched. In this paper, an active suspension based on a torsion bar is modeled and analyzed under the excitation from standardized road profiles according to the ISO 8608 norm. A skyhoo…
A Computational Approach to Vibration Control of Vehicle Engine-Body Systems
2012
In recent years, the noise and vibration of cars have become increasingly important [20, 23, 29, 30, 35]. A major comfort aspect is the transmission of engine-induced vibrations through powertrain mounts into the chassis (see Figure 1). Engine and powertrain mounts are usually designed according to criteria that incorporate a trade-off between the isolation of the engine from the chassis and the restriction of engine movements. The engine mount is an efficient passive means to isolate the car chassis structure from the engine vibration. However, the passive means for isolation is efficient only in the high frequency range. However the vibration disturbance generated by the engine occurs mai…
Optimal Damping Constant Investigation on a Quarter-Car
2013
This paper shows an investigation on optimal damping constant performed in the frequency domain. The optimal damping constant is meant as that value that minimizes the acceleration of all connected bodies characterizing a two degree of freedom system sketching a quarter car. The connected bodies are sprung and unsprung mass respectively for quarter of chassis and tire, this last keeps the contact with the ground and it is connected with the sprung mass through a shock absorber characterized by spring and fluid damper. Optimal damping constant was determined by imposing analytical conditions on the expression of acceleration of two masses. Afterwards, the variation of acceleration and positi…
Characterization of the Dynamic Interaction between Chassis and Powertrain of a Vehicle Using the Coupling Matrix
2013
International audience; This study is concerned with the vibration transmission between two subsystems of a vehicle: the chassis which is considered as an elastic structure and the powertrain which is considered as a rigid body. The study is carried out based on a new coupling matrix constructed from equations of dynamic behavior of each subsystems. This matrix depends only on the impedance matrices of the two subsystems and the mechanical characteristics of the linking mounts. Under some assumptions, a simplified expression to obtain the overall behaviour of the entire system is proposed. Despite its sensitivity to the degree of coupling between the subsystems, this method can be applied t…
Application of Genetic Algorithm on Parameter Optimization of Three Vehicle Crash Scenarios
2017
Abstract This paper focuses on the development of mathematical models for vehicle frontal crashes. The models under consideration are threefold: a vehicle into barrier, vehicle-occupant and vehicle to vehicle frontal crashes. The first model is represented as a simple spring-mass-damper and the second case consists of a double-spring-mass-damper system, whereby the front mass and the rear mass represent the vehicle chassis and the occupant, respectively. The third model consists of a collision of two vehicles represented by two masses moving in opposite directions. The springs and dampers in the models are nonlinear piecewise functions of displacements and velocities respectively. More spec…
A state-space approach to mathematical modeling and parameters identification of vehicle frontal crash
2014
In this paper a state-space estimation procedure that relies on the time-domain analysis of input and output signals is used for mathematical modeling of vehicle frontal crash. The model is a double-spring–mass–damper system, whereby the front mass and real mass represent the chassis and the passenger compartment, respectively. It is observed that the dynamic crash of the model is closer to the dynamic crash from experimental when the mass of the chassis is greater than the mass of the passenger compartment. The dynamic crash depends on pole placement and the estimated parameters. It is noted that when the poles of the model are closer to zero, the dynamic crash of the model is far from the…
Influence of compliance for an elastokinematic model of a proposed rear suspension
2014
The research is carried out to improve passenger’s comfort to increase the vehicles stability in dynamic conditions. The literature available in the automotive engineering considers different topics for studying suspensions. An example represents mechanisms structure and analysis (synthesis, kinematics, and dynamics) under various operating conditions. These aspects have been approached before analytically, numerical. The current paper studies the influence of the lateral force on the contact patch of the wheel and the corresponding variations of vehicle stability parameters, such as camber angle and wheel rear track. The study is performed for a newer innovative rear suspensions mechanism …
Algorithms for skiascopy measurement automatization
2014
Automatic dynamic infrared retinoscope was developed, which allows to run procedure at a much higher rate. Our system uses a USB image sensor with up to 180 Hz refresh rate equipped with a long focus objective and 850 nm infrared light emitting diode as light source. Two servo motors driven by microprocessor control the rotation of semitransparent mirror and motion of retinoscope chassis. Image of eye pupil reflex is captured via software and analyzed along the horizontal plane. Algorithm for automatic accommodative state analysis is developed based on the intensity changes of the fundus reflex.
Modulation of Intracellular O-2 Concentration in Escherichia coli Strains Using Oxygen Consuming Devices
2018
International audience; The use of cell factories for the production of bulk and value-added compounds is nowadays an advantageous alternative to the traditional petrochemical methods. Nevertheless, the efficiency and productivity of several of these processes can improve with the implementation of micro-oxic or anoxic conditions. In the industrial setting, laccases are appealing catalysts that can oxidize a wide range of substrates and reduce O-2 to H2O. In this work, several laccase-based devices were designed and constructed to modulate the intracellular oxygen concentration in bacterial chassis. These oxygen consuming devices (OCDs) included Escherichia coil's native laccase (CueO) and …
Semiactive Control Methodologies for Suspension Control With Magnetorheological Dampers
2012
Authors version of an article published in the journal: IEEE/ASME Transactions on Mechatronics. Also available from the publisher at: http://dx.doi.org/10.1109/TMECH.2011.2107331 Suspension systems are one of the most critical components of transportation vehicles. They are designed to provide comfort to the passengers to protect the chassis and the freight. Suspension systems are normally provided with dampers that mitigate these harmful and uncomfortable vibrations. In this paper, we explore two control methodologies (in time and frequency domain) used to design semiactive controllers for suspension systems that make use of magnetorheological dampers. These dampers are known because of th…