Search results for "Chimica Fisica"
showing 10 items of 978 documents
The influence of the nature of the surface oxide on the adhesive fracture energy of aluminium-bonded joints as measured by T-peel tests
2008
Abstract Modification of aluminium alloy substrates microstructure and morphology by depositing new oxide layers on top of the metal surface has been investigated, with the aim of improving adhesion. The effect of treating the metal with boiling water or immersing it in a cerate bath has been studied by means of electron microscopy, contact angle measurements and peeling tests. The formation of pseudoboehmite layers or cerium conversion coatings both led to an increase in joint's adhesive fracture energy and more durable adhesive bonds with respect to joints obtained with “mechanically grinded only” substrates. Differences in the performance of the bonded joints has been discussed in terms …
Anodizing and post-anodizing processes to enhance corrosion resistance of Al alloys
2021
In this work the dependence of corrosion resistance of Al alloys AA 2024-T3 on sealing treatments was studied. AA 2024-T3 samples were anodized at 14 V in a bath containing sulfuric and tartaric acids. Anodized samples were sealed with four different treatments: hot water, vapour, hot water with salts and stirred hot water. Electrochemical Impedance Spectroscopy measurements were performed to estimate samples' corrosion resistance in a solution simulating sea water environment. Samples sealed in hot water showed the highest corrosion resistance.
Effect of TiO2 and Al2O3 Addition on the Performance of Chitosan/Phosphotungstic Composite Membranes for Direct Methanol Fuel Cells
2023
Composite chitosan/phosphotungstic acid (CS/PTA) with the addition of TiO2 and Al2O3 particles were synthesized to be used as proton exchange membranes in direct methanol fuel cells (DMFCs). The influence of fillers was assessed through X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, liquid uptake, ion exchange capacity and methanol permeability measurements. The addition of TiO2 particles into proton exchange membranes led to an increase in crystallinity and a decrease in liquid uptake and methanol permeability with respect to pristine CS/PTA membranes, whilst the effect of the introduction of Al2O3 particles on the characteristics of membranes is almost the op…
Ni-Based Alloy Nanostructured Electrodes for Alkaline Electrolyzers
In water alkaline electrolyzer field, the development of Nickel-based nanostructured electrode is one of the possible ways to improve the water electrolysis efficiency
Materiali ibridi a base di nanotubi di allosite per la rimozione d’inquinanti
2017
L’allosite (HNT) è un interessante materiale argilloso allumino-silicato naturale, non tossico e biocompatibile, con la caratteristica forma tubolare cava dotata di parziale carica positiva interna e negativa esterna.Combinando le peculiarità di un composto organico con le proprietà di un materiale inorganico, è possibile ottenere sistemi ibridi organici–inorganici con interessanti proprietà e vasti campi di applicazione. Sono un esempio delle “nanospugne” capaci di adsorbire efficacemente potenziali inquinanti. In questo contesto sono stati preparati, dei materiali ibridi “spugna” costituiti da unità ciclodestriniche e allosite e ancora un sistema ibrido HNT-Cucurbit[8]uril. Il primo possi…
Co-precipitation synthesis of Nd:YAG nano-powders: the effect of Nd dopant addition with thermal treatment
2007
Nanopowders of Yttrium Aluminium Garnet doped with neodymium ions were obtained by the co-precipitation method from the reaction of aluminium, yttrium and neodymium nitrate with ammonia. The amount of neodymium was selected in order to produce samples of nominal stoichiometry NdXY (3-X)Al5O12 (where X = 0.006, 0.012, 0.024, 0.048, 0.081, 0.096, 0.17, 0.19, 0.38, 0.54, and 0.72, respectively). After washing and drying, the hydroxide precursors were subjected to Thermo-Gravimetry and Differential Thermal Analysis experiments from room temperature up to 1500 °C, which showed the presence of exothermal events accompanying phase transformation phenomena. X-ray diffraction investigations conducte…
The Effect of Electronic Properties of Anodized and Hard Anodized Ti and Ti6Al4V on Their Reactivity in Simulated Body Fluid
2022
The electronic properties of barrier and porous layers on Ti and Ti6Al4V were studied. Barrier anodic oxides grown to 40 V on Ti and on Ti6Al4V are both n-type semiconductors with a band gap of 3.3 eV and 3.4 eV respectively, in agreement with the formation of amorphous TiO2. Anodizing to 200 V at 20 mA cm−2 in calcium acetate and β-glycerol phosphate disodium pentahydrate leads to the formation of Ca and P containing porous films with a photoelectrochemical behaviour dependent on the metallic substrate. A band gap of 3.2 eV and the flat band potential of −0.5 V vs Ag/AgCl were measured for the porous oxide on Ti, while optical transitions at 2.15 eV and a significantly more positive flat b…
On the formation of inclusion complexes at the solid/liquid interface of anchored temperature-responsive PNIPAAM diblock copolymers with γ-cyclodextr…
2017
The thermal responsive behavior of adsorbed layers of diblock copolymers of poly(N-isopropylacrylamide) (PNIPAAM) and poly((3-acrylamidopropyl)trimethylammonium chloride) (PAMPTMA(+)) with γ-cyclodextrin (γ-CD) at the solid/liquid interface has been investigated using three in situ techniques: null ellipsometry, quartz–crystal microbalance with dissipation monitoring, and neutron reflectometry. The measurements provided information about the adsorbed amounts, the layer thickness, hydration and viscoelastic properties, and the interfacial structure and composition. The copolymers adsorb to silica with the cationic PAMPTMA(+) blocks sitting as anchors in a flat conformation and the PNIPAAM ch…
Blue luminescent amino-functionalized graphene quantum dots as a responsive material for potential detection of metal ions and malathion
2022
Large amounts of hazardous and toxic substances in the environment require non-toxic, cheap, easy, rapid, and sensitive methods for their detection. Blue luminescent graphene quantum dots (GQDs) were produced by electrochemical cleavage of graphite electrodes followed by gamma irradiation in the presence of ethylenediamine (EDA). Modified dots were able to detect metal ions (Co2+, Pd2+, Fe3+) due to photoluminescence quenching. The highest sensitivity was detected for the sample irradiated at a dose of 25 kGy. The limits of detection (LODs) were 1.79, 2.55, and 0.66 μmol L−1 for Co2+, Fe3+, and Pd2+, respectively. It was observed that GQDs irradiated at 200 kGy act as an ultra-sensitive tur…
Characterization of Thin Passive Film-Electrolyte Junctions. The Amorphous Semiconductor (a-SC) Schottky Barrier Approach.
2017
A detailed study of the electronic properties of thin (< 20 nm) anodic TiO2 potentiostatically grown on titanium in two different solutions is presented. The results show that the nature of the anodizing solution affects the electronic properties of the anodic film and in particular the density of electronic state (DOS) distribution. Different DOS were derived from the experimental data analyzed according to the theory of amorphous semiconductor (a-SC) Schottky barrier. It is shown that the usual non-linear and frequency dependent Mott-Schottky plots are in agreement with expected theoretical behaviour of a-SC Schottky barrier. It is shown the importance of the DOS distribution in determini…