Search results for "Chip"

Influenza dei chips di quercia, di diversa origine e livello di tostatura, nella vinificazione in bianco

2011

Recognition of Chip Forms by Means of Dynamic Force Spectrum Analysis

1993

In this study the ability to identify chip forms occurrs in the turning of austenitic stainless steel using dynamic force spectrum analysis has been tested. For this purpose the frequency spectra obtained from various metal cutting tests were recorded along with the static cutting forces. A dual channel analysis, based on the Fast Fourier Transform (FFT), was adopted to help identify the continuous/discontinuous (favourable/unfavourable) chip forming boundary. The results showed an acceptable correlation between the types of the frequency spectra and the types of chip forms. Finally, an original classification of the spectra obtained during turning of AISI 304 (DIN 1.4301) stainless steel i…

Economic assessment of Eucalyptus (spp.) for biomass production as alternative crop in Southern Italy

2015

The increase in energy prices and the stagnation of sales prices of the main agricultural commodities required a rethinking of farm production strategies. Since during the last years, thanks to a series of policies aimed at promoting renewable sources it has been a rapid diffusion of lignocellulosic biomass species, this paper aimed at evaluating the economic feasibility of the introduction of eucalyptus (Eucalyptus spp.) as energy crop for farmers of Southern Italy, by comparing it with traditional crop rotations. In particular, economic analysis has been carried out in a representative case study located in the Sicilian hilly hinterland where, in 2013, it has been built a biomass plant fo…

Modelling of Final Plastic Deformation in the Case of Continuous Straight-Edged Oblique Cutting

1992

This paper presents a complex oblique cutting model for the case of varying chip formation conditions and its practical application in relation to the results of degree of final plastic deformation in the primary shear zone is considered. A computer procedure for prediction of the shear angle is given and the place of the oblique cutting process among the results obtained previously is established.

Co-simulation platform based on systemc for multiprocessor system on chip architecture exploration

2007

Currently multiprocessor embedded systems are the principal vectors of semiconductor industry. Modelling, validating and analyzing a system performances impose the evolution of the traditional simulation techniques. In this paper we define the methodology we used in constructing the STARSoC co-simulation environment. This platform aims to explore at higher levels of abstractions a multiprocessors system on chip architectures. The platform reference design contains several OpenRISC 1200 Instruction Set Simulators (ISSs) wrapped under SystemC, and some basic peripherals within the SystemC simulation framework. Our purpose is to develop a complete design space exploration tool. In order to ass…

Optoelectronic Module with Integrated Transceiver and Mux-Demux for Optical Interconnect Applications

2019

The design, development and improvtableement in electronic devices and components have led to the further miniaturization of the system devices and their interconnecting interfaces. Hence, reducing the size of the transmitter (Tx) chips, receiver (Rx) chips and associated components play an important role in designing a reduced/small sized optoelectronic modules for optical interconnect applications. Some of the associated components include multiplexer, demultiplexer, clock and data recovery circuits (CDR), etc. Therefore, in this paper we present an optoelectronic module with integrated transceiver (Tx-Rx) and multiplexer-demultiplexer (mux-demux) with the aim of reducing the total area o…

Georeferenced cartography dataset of the La Fossa crater fumarolic field at Vulcano Island (Aeolian Archipelago, Italy): conversion and comparison of…

2011

The present study illustrates the procedures applied for the coordinate system conversion of the historical fumarole positions at La Fossa crater, to allow their comparison with newly acquired global positioning system (GPS) data. Due to the absence of ground control points in the field and on both the old Gauss Boaga and the new UTM WGS 1984 maps, we had to model the transformation errors between the two systems using differential GPS techniques. Once corrected, the maps show a residual Easting shifting, due to erroneous georeferencing of the original base maps; this is corrected by morphological comparative methods. The good correspondence between the corrected positions of the historical…

A new ATLAS muon CSC readout system with system on chip technology on ATCA platform

2015

The ATLAS muon Cathode Strip Chamber (CSC) backend readout system has been upgraded during the LHC 2013-2015 shutdown to be able to handle the higher Level-1 trigger rate of 100 kHz and the higher occupancy at Run 2 luminosity. The readout design is based on the Reconfigurable Cluster Element (RCE) concept for high bandwidth generic DAQ implemented on the Advanced Telecommunication Computing Architecture (ATCA) platform. The RCE design is based on the new System on Chip XILINX ZYNQ series with a processor-centric architecture with ARM processor embedded in FPGA fabric and high speed I/O resources together with auxiliary memories to form a versatile DAQ building block that can host applicati…

Development of a microfluidic design for an automatic lab-on-chip operation

2016

Simple and easy to use are the keys for developing lab-on-chip technology. Here, a new microfluidic circuit has been designed for an automatic lab-on-chip operation (ALOCO) device. This chip used capillary forces for controlled and precise manipulation of liquids, which were loaded in sequence from different flowing directions towards the analysis area. Using the ALOCO design, a non-expert user is able to operate the chip by pipetting liquids into suitable inlet reservoirs. To test this design, microfluidic devices were fabricated using the programmable proximity aperture lithography technique. The operation of the ALOCO chip was characterized from the flow of red-, blue- and un-dyed deioni…

Prognostic Impact of let-7e MicroRNA and Its Target Genes in Localized High-Risk Intestinal GIST: A Spanish Group for Research on Sarcoma (GEIS) Study

2020

MicroRNAs (miRNAs) are small non-coding RNAs that negatively regulate gene expression at the post-transcriptional level, and they have been described as being associated with tumor prognosis. Here, miRNA profiling was planned to explore new molecular prognostic biomarkers in localized intestinal high-risk GIST. Paraffin tumor blocks of 14 and 86 patients were used in the discovery and expansion sets, respectively. GeneChip miRNA v3.0 was employed to identify the miRNAs differentially expressed between relapsed and non-relapsed patient samples, which were validated in the expansion set, by qRT-PCR. RT2 Profiler PCR Array was used for the screening of let-7e targets. Expression levels were co…