Search results for "Chronoamperometry"
showing 10 items of 18 documents
Electrochemical deposition of aniline derivatives for conductometric gas sensors
2019
International audience; Polymer film of poly(2,3,5,6-tetrafluoroaniline) (PTFA) were electroplated on ITO substrate from acidic medium by chronoamperometry. Electrochemical and morphological characterizations were performed and compared to polyaniline properties similarly coated. It seemed that PTFA film had an irreversible redox response with poor conductivity due to the absence of acid-base doping. This film were then incorporated in a patented device called MSDI heterojunction to perform ammonia sensing in humid atmosphere.
Spatially limited diffusion coupled with ohmic potential drop and/or slow interfacial exchange: a new method to determine the diffusion time constant…
2004
Abstract We have analyzed chronoamperometric curves, I ( t ), after small-amplitude potential steps Δ E (PITT technique) for the model of linear diffusion of a species inside an electroactive film, taking into account ohmic effects in the external media (solution and electrode) as well as a finite rate of the interfacial exchange. For its short-time interval, t ≪ τ d ( τ d is the diffusion time constant, corresponding to unlimited diffusion from the interface), three approximate analytical expressions have been proposed. One of these represents an interpolation formula between the value of the current at the start of the diffusion process, I (0)=Δ E / R ext (after the end of the EDL chargin…
Electrochemical incineration of oxalic acid at boron doped diamond anodes: Role of operative parameters
2008
The electrochemical incineration of oxalic acid (OA) at boron doped diamond (BDD) anodes was investigated both theoretically and experimentally in order to find the influence of the operative parameters on the performances of the process. Polarization curves and chronoamperometric measurements indicate the probable occurrence of a direct electrochemical oxidation of OA at the surface of the BDD anode at low pH and of a hydroxyl radical-mediated reaction at high pH. When incineration electrolyses are performed at low pH with potentiostatic alimentation, a dramatic influence of the potential is observed. In amperostatic incineration, high CE are obtained when most part of the process was unde…
An electrochemical quartz crystal microbalance study of lithium insertion into thin films of tungsten trioxide II. Experimental results and compariso…
1995
Abstract Lithium insertion into amorphous thin films of tungsten trioxide (a-WO 3 ) prepared by thermal vacuum evaporation of WO 3 powder has been studied experimentally by chronoamperometry, cyclic voltammetry and ac impedance spectroscopy associated with electrochemical quartz crystal microbalance (EQCM). During cathodic polarization of the electrode and at short times two antagonistic processes occur. One is a non faradaic process and is associated with the expulsion of anions from the electrode surface under the effect of the electric field built in the electrolyte when a potential difference is imposed between the electrodes. The other one is the faradaic insertion of non-solvated lith…
Electrochemical performance of activated screen printed carbon electrodes for hydrogen peroxide and phenol derivatives sensing
2019
Screen-printed carbon electrodes (SPCEs) are widely used for the electroanalysis of a plethora of organic and inorganic compounds. These devices offer unique properties to address electroanalytical chemistry challenges and can successfully compete in numerous aspects with conventional carbon-based electrodes. However, heterogeneous kinetics on SPCEs surfaces is comparatively sluggish, which is why the electrochemical activation of inks is sometimes required to improve electron transfer rates and to enhance sensing performance. In this work, SPCEs were subjected to different electrochemical activation methods and the response to H2O2 electroanalysis was used as a testing probe. Changes in to…
An electrochemical quartz crystal microbalance study of lithium insertion into thin films of tungsten trioxide I. Modeling of the ionic insertion mec…
1995
A theoretical description of the mechanism of lithium insertion into amorphous thin films of tungsten trioxide (a-WO3) prepared by thermal vacuum evaporation of WO3 powder is presented. The model developed is based on the experimental results obtained by chronoamperometry and ac impedance spectroscopy associated with electrochemical quartz crystal microbalance (EQCM). The electrode mass change and the current flowing through the electrochemical cell during cathodic polarization are simulta neously recorded. As expected, it can be observed that the insertion process is associated with a gain of mass of the inserted electrode at long times (t > 1 s). On the other hand at short times (t < 1 s)…
(Photo)catalyst Characterization Techniques
2019
Abstract This chapter reports on some characterization techniques that are commonly used for catalysts and photocatalysts. Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), UV–visible (UV–Vis), photoluminescence (PL), and electrochemical characterization techniques are presented with experimental details and actual case studies from literature are discussed. The chapter starts with adsorption phenomena on (photo)catalysis and adsorption isotherms are presented. Then BET analysis technique and its applications in (photo)catalysis are explained. Morphological properties (SEM), functional groups, and the interaction of substrate (…
A nanostructured sensor of hydrogen peroxide
2017
Abstract A nanostructured electrochemical sensor of hydrogen peroxide was fabricated growing self-standing Pd nanowires (Pd NWs) into polycarbonate (PC) membranes through a simple metal galvanic deposition. Conditions of deposition were adjusted in order to attain 2–5 μm long Pd wires. Characterization of Pd-NWs was performed by scanning electrode microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. Properties of the nanostructured sensor were studied by cyclic voltammetry and chronoamperometry in phosphate buffer—ethanol solution. Addition of pure ethanol to the test solution was essential in order to increase wettability of the nanostructures. Sensing features were comp…
Bending Sensors Based on Thin Films of Semitransparent Bithiophene-Fulleropyrrolidine Bisadducts
2020
In this study, a novel bithiophene‐fulleropyrrolidine bisadducts system (bis‐Th2PC 60 ) was synthesized and electropolymerized by chronoamperometry onto flexible ITO/PET substrates. The resulting semitransparent thin film was characterized by XPS, FT‐IR, cyclic voltammetry and optical techniques, confirming the good outcome of the electropolymerization process. AFM investigations permitted to highlight an inherent disordered granular morphology, in which the grain‐to‐grain separation depends upon the application of bending. The electrical resistance of the thin film was characterized as function of bending (in the range 0°‐90°), showing promising responsivity to low bending angles (10°‐30°)…
Fabrication of a biocompatible and continuous glucose biosensor with the poly(3,4-ethylenedioxythiophene) modified electrode
2019
Abstract In this study, we have explored the potentiality of using GOx/AuNP/PEDOT(BSA)/Pt electrode as an implantable, long-lasting, and sensitive glucose biosensor. We have examined the performance of the electrode for glucose calibration with three electrochemical measurements, such as cyclic voltammetry, linear sweep voltammetry, as well as chronoamperometry, which all exhibited strong linear correlation between resulting signal and glucose concentration. In comparison, linear sweep voltammetry gave the best linear sensitivity, whose average was about 3.124 µA/mM/cm2 within a wide glucose concentration range from 0.416 to 50 mM. Meanwhile, the stability of the electrode was confirmed by …