Search results for "Compaction"
showing 10 items of 105 documents
Fatigue and Healing Properties of Low Environmental Impact Rubberized Bitumen for Asphalt Pavement
2017
The addition of recycled tyre rubber as a modifier to enhance the mechanical properties of bitumen has proven to provide asphalt mixtures with better mechanical performance. However the rubberised bitumen presents the limitation of requiring higher manufacturing and compaction temperatures. This could be solved by subjecting the tyre rubber to sort of pre-treatments such as: Adding warm-mix additives and/or using partial devulcanisation. These solutions have the potential of lowering the overall environmental impact of the asphalt pavement, however it is still not clear whether these can be detrimental for the rubberized asphalt binder mechanical properties. This paper investigates the effe…
Unveiled the Source of the Structural Instability of HKUST-1 Powders upon Mechanical Compaction: Definition of a Fully Preserving Tableting Method
2018
Metal–organic frameworks (MOFs) are getting closer to finally being used in commercial applications. In order to maximize their packing density, mechanical strength, stability in reactive environme...
Using the single-ring infiltrometer method to detect temporal changes in surface soil field-saturated hydraulic conductivity
2004
Abstract Determining temporal changes in field-saturated hydraulic conductivity ( K fs ) is important for understanding and modelling hydrological phenomena at the field scale. Little is known about the sensitivity of temporal change estimates to the method used for measuring K fs . The objective of this study was to compare temporal changes in K fs obtained in the surface layer of a clayey soil using two application procedures of the single-ring infiltrometer method. Rings installed permanently at the beginning of a 1.5-year study period (permanent sites, PSs, sample size N =16) and rings installed immediately before conducting the infiltrometer measurement (non-permanent sites, NPSs, N =1…
Thermal-electrical-mechanical simulation of the nickel densification by Spark Plasma Sintering. Comparison with experiments
2016
Abstract Spark Plasma Sintering is a non-conventional process of the powder metallurgy field which uses a high electrical current to rapidly produce fully dense materials. In the present paper, a thermal-electrical-mechanical model developed on ABAQUS Software is proposed to simulate the densification of a nickel disk. A compaction model, studied in [Wolff, C., Mercier, S., Couque, H., Molinari, A., 2012. Modeling of conventional hot compaction and spark plasma sintering based on modified micromechanical models of porous materials. Mechanics of Materials 49 (0), 72–91. URL http://www.sciencedirect.com/science/article/pii/S0167663611002195 ], has been used to reproduce the densification of t…
Comparison between a Uniaxial Compaction Tester and a Shear Tester for the Characterization of Powder Flowability
2014
The complete characterization of powder flow properties with shear cells is a long and time-consuming process that requires specially trained operators or costly automated instruments. For these reasons, in industrial practice, the use of simpler and less extensive measurement by uniaxial compaction testers is often preferred. However, previous studies in the literature indicate that the results of the two techniques are not directly comparable due to the different stress state conditions achieved in the two testers.In this study, an experimental campaign to measure the flow function of five different powders with a ring shear tester (RST) and a uniaxial compaction tester (UCT) was performe…
Sintering of Fe2NiO4 with an internal binder: a way to obtain a very dense material
2003
Abstract The coupled synthesis and sintering of Fe2NiO4 can be carried out from the calcination under air at high temperatures (>1200 °C) of precompacted (under 12 MPa) pellets of different mixtures: NiO/α-Fe2O3; NiO/α-Fe2O3/Fe; NiO/α-Fe2O3/Ni. The densest material is obtained at 1200 °C only from the following mixture: NiO (40 mol%), α-Fe2O3 (50 mol%) and Ni (10 mol%). Because the metallic nickel is very ductile, it is used as an internal binder in order to enhance the precompacting of the samples. Moreover, the role of nickel is to enhance the sintering reaction. This route leads to a final material of relative density close to 98±2%.
Long-term sealing ability of GuttaFlow versus Ah Plus using different obturation techniques.
2010
Objective. To compare the long-term sealing ability of GuttaFlow® using different obturation techniques. Study Design. Three hundred teeth, prepared with a crown-down technique, were divided into thirty experimental groups (n=10) to evaluate the apical and coronal leakage, at 3, 30 and 120 days, of lateral compaction gutta-percha + AH Plus?, lateral compaction gutta-percha + GuttaFlow®, single cone + AH Plus?, single cone + GuttaFlow®, and GuttaFlow® only. Results. Both coronal and apical leakage, at the three times of measurement, no significant differences were found among GuttaFlow® + lateral compaction gutta-percha and GuttaFlow® + single cone groups, whereas the only GuttaFlow® reached…
Sealing ability of lateral compaction and tapered single cone gutta-percha techniques in root canals prepared with stainless steel and rotary nickel …
2011
Objectives: The aim of this study was to evaluate the sealing ability of lateral compaction and tapered single cone gutta-percha techniques in root canals prepared with stainless steel and rotary nickel titanium root canal instruments by fluid filtration method. Study design: The root canals were prepared with stainless steel (SS) and nickel titanium (NiTi) instruments. The canals prepared with SS were obturated with lateral compaction technique using .02 tapered cones and the canals prepared with NiTi instruments were obturated with lateral compaction technique using .02 tapered cones or 06 tapered single cones. The amount of leakage was evaluated by fluid filtration model. The results wer…
System B, Endo-Twinn and E-Fill. True temperatures inside the canal
2012
Background: The aim of this study is to verify the variations of the temperature inside the root canal with three different gutta-percha heating systems. Materials and Methods: A split-tooth model was built with a lateral groove at 3.5-mm from working length (WL) in order to insert a Chromel-Alumel K-type thermocouple placed in contact with gutta-percha. The thermocouple was connected to a digital thermometer. Sixty obturations were made with medium gutta-percha points. For 20 specimens the System B was used with the Buchanan fine plugger and the temperature was set at 200°C; for other 20 specimens the Endo-Twinn with a fine plugger was used and for the last 20 specimens we used the E-Fill …
Laboratory mix design of asphalt mixture containing reclaimed material
2014
This paper presents a study on the production of asphalt test specimens in the laboratory containing reclaimed asphalt. The mixtures considered were stone mastic asphalt concrete mixtures containing up to 30% of reclaimed asphalt. Specimens were compacted to the reference density obtained from the Marshall mix design. Gyration compaction method was used for preparing specimens for the experimental programme, while coring and cutting methods and X-ray computed tomography (CT) were used to investigate the change in properties within the specimens and to validate the selected methodology. The study concluded that gyratory compaction is suitable to produce homogeneous test specimens also for mi…