Search results for "Composite"

Morphology and mechanical properties of extruded ribbons of LDPE/PA6 blends compatibilized with an ethylene-acrylic acid copolymer

2003

Two grades of low density polyethylene (LDPE) were blended with polyamide-6 (PA) in the 75/25 and 25/75 wt/wt ratios and shaped into ribbons with a Brabender single screw extruder. An ethylene-acrylic acid copolymer (EAA) was used in the 2 phr concentration as a compatibilizer precursor (CP). The morphology of the ribbons and its evolution during high temperature annealing were investigated by scanning electron microscopy (SEM). The results confirmed that EAA does actually behave as a reactive compatibilizer for the LDPE/PA blends. In fact, in the presence of EAA, the interfacial adhesion is improved, the dispersion of the minor phase particles is enhanced and their tendency toward fibrilla…

Phase separation of polymer blends in solution: A case study

2016

Abstract The phase behavior and phase separation features of the quaternary system poly- l -lactide (PLLA)/poly-rac-lactide (PLA)/dioxane/water were investigated. Experiments were performed with fixed total polymer concentration of 6 wt%, by varying the PLLA/PLA weight ratio. Blend weight compositions examined were 100/0, 80/20, 50/50, 20/80 and 0/100, at fixed dioxane/water weight ratio (87/13). Cloud point measurements reported that the demixing temperatures of blends are close to PLLA in the same mixed solvent, in line with the calculated spinodals. As regards to foam preparation, above the PLA cloud point, morphology is similar to pure PLLA foams; conversely, below PLA cloud point, the …

Effect of the nanotube aspect ratio and surface functionalization on the morphology and properties of multiwalled carbon nanotube polyamide-based fib…

2013

In this study, the effect of the carbon nanotube (CNT) aspect ratio and surface functionalization on the mechanical behavior and morphological changes of polyamide (PA)-based fibers was investigated. Composites were prepared by the melt blending of CNTs with PA, and at a later time, the fibers were prepared by melt spinning and cold drawing. A reinforcement effect was noticed for all of the CNTs samples, and the increase in the mechanical properties and dimensional stability was more pronounced for highly oriented filaments. When the elongational flow was increased, the orientation of CNTs along the fiber direction was observed, but the nanotube alignment was much more difficult for CNTs wi…

Preparation of polymeric foams with a pore size gradient via Thermally Induced Phase Separation (TIPS)

2015

Abstract Foams with a pore size gradient are promising materials for tissue engineering applications where a complex architecture involving morphological variations in space must be mimicked, e.g. in bone tissue repair. In this paper, a technique to obtain a porous scaffold with a pore size gradient is presented. The preparation procedure is based on Thermally Induced Phase Separation (TIPS), by imposing a different thermal history on the two sides of a polymeric solution. In this way, a gradient in thermal history is produced, which will generate a pore size monotonously varying along scaffold thickness. By controlling some parameters easy to manipulate, such as demixing temperature and/or…

Effect of ageing on the morphology and creep and recovery of polymer-modified bitumens

2018

Polymer additives are used to improve the properties of road bitumens including their oxidative resistance. However, their usage as anti-oxidative materials remains relatively unclear. This study aims to investigate the changes in the morphology and the rheological response of polymer modified bitumens used in road pavement construction caused by ageing. An elastomer (radial styrene butadiene styrene, SBS) and a plastomer (ethyl vinyl acetate, EVA) polymer were mixed with one base bitumen at three polymer concentrations. The bitumens were RTFO and PAV aged. The morphology of the bitumens was captured by fluorescence microscopy while the rheological properties were measured by means of the m…

Morphology, mechanical properties and thermal degradation kinetics of PMMA-zirconia nanocomposites prepared by melt compounding

2012

Zirconia nanoparticles were synthesized by means of a sol-gel method and embedded in poly(methyl methacrylate) (PMMA) by melt compounding. The zirconia was well dispersed in the PMMA matrix, with only a few clusters, especially for the highest investigated zirconia content. NMR results showed heteronuclear dipolar interactions involving the carbons and the surrounding hydrogen nuclei. The effect of the amount of zirconia, in the range of 1–5!wt%, on the thermomechanical properties and thermal degradation kinetics of PMMA was also investigated by means of dynamic mechanical analysis (DMA), thermogravimetric analyses (TGA), and Fourier-transform infrared spectroscopy (FTIR). The presenc…

Morphology and properties of polyamide/CNTs nanocomposite fibres

2010

Investigating the effect of residual stress on hydrogen cracking in multi-pass robotic welding through process compatible non-destructive testing

2021

Abstract In this paper, the effect of Welding Residual Stress (WRS) on the size and morphology of hydrogen-induced cracks (HIC) is studied. Four samples were manufactured using a 6-axis welding robot and in two separate batches. The difference between the two batches was the clamping system used, which resulted in different amounts of welding deformation and WRS. The hydrogen cracks were intentionally manufactured in the samples using a localised water-quenching method, where water was sprayed over a specific weld pass in a predetermined position. The Phased-Array Ultrasonic Testing (PAUT) system was implemented during the welding process (high-temperature in-process method), to detect the …

Indicadores compuestos como metodología innovadora en Comunicación. Aplicación para la evaluación de los medios públicos europeos

2020

The currently dominant scientific production model in the field of Communication exhibits an excess of standardization towards mainly empirical work that is overwhelming caried out using quantitative techniques based on simple statistical analyses, in many cases limiting the presentation of results to a reading of the available data. This article presents an innovative proposal in this area, designed as a new form of dissemination and scientific presentation, with the objective of constructing three composite indicators that, when applied to European public service media, will enable the assessment of the perception of their social value, independence, and management efficiency. Another aim…

The Material Deprivation of Foreigners: Measurement and Determinants

2016

We examine the material deprivation of foreigners on a sub-sample of the 2009 Italian Survey on Income and Living Conditions carried out by Istat. We employ an index of material deprivation that takes into account the regional level of analysis, and relies on the assignment of weights to deprivation items. The effects produced on material deprivation by several variables, interpreted as determinants, are investigated through a zero-inflated beta regression model.