Search results for "Composite"

Size dependence of the Josephson critical behavior in pyrolytic graphite TEM lamellae

2014

We have studied the transport characteristics of TEM lamellae of different widths obtained from a graphite sample with electrical contacts at the edges of the embedded interfaces. The temperature dependence of the resistance, as well as the current-voltage characteristics, are compatible with the existence of Josephson-coupled superconducting regions. The transition temperature at which the Josephson behavior sets in decreases with a decreasing interface width and vanishes for widths below 200 nm. This interface-size dependence provides an explanation for differences observed in the transport behavior of graphite-based samples with interfaces, and it appears to be related to the influence o…

On the determination of vortex creep parameters in superconductors using standard magnetization relaxation data

2011

The relaxation of the irreversible magnetic moment m(t) in YBa2Cu3O7 (YBCO) films was investigated as a function of temperature T and the external magnetic field H along the c axis applied in zero-field cooling conditions, for the determination of vortex creep parameters. The data analysis was performed using the T and current density dependence of the normalized vortex creep activation energy, or by the fit of the m(t) data with the well known interpolation formula in the framework of the general vortex creep equation. It was found that (i) even for specimens with strong static pinning the characteristic pinning energy remains small in the low-T range, where the vortex creep appearing in s…

Improvement of the critical current density of spark plasma sintered MgB2by C60addition

2010

We investigated the influence of fullerene (C60) addition on the superconducting parameters of MgB2 bulk samples obtained by spark plasma sintering (SPS). It was found that 1.5?wt% C60 addition leads to the reduction of the critical temperature by a few K, whereas the magnetically determined critical current density increases by approximately one order of magnitude in an applied magnetic field H = 70?kOe at temperature T = 10?K. This indicates substitution of B by C in C60 added MgB2 processed by SPS, contrary to some data reported in the literature obtained using conventional methods. For our relatively large specimens, the occurrence of macroscale flux jumps was observed over a wide (H, T…

Preparation and x-ray pole-figure characterization of DC-sputtered Bi-2201, Bi-2212 and Bi-2223 thin films

1997

Thin films of the three members of the superconducting series , n = 1,2,3, were prepared by diode sputtering. X-ray characterization shows that all the films are single phase and c-axis oriented and in addition they are epitaxially grown. The latter is found by x-ray pole-figure measurements taken with a four-circle diffractometer. These are emphasized in this work. AC susceptibility measurements show that, while the 2201 films are not superconducting until 4 K, the transition temperatures of the 2212 films are 82 K - 90 K and of the 2223 films 84 K - 89 K.

High quality superconducting titanium nitride thin film growth using infrared pulsed laser deposition

2018

The quantum phase slip phenomenon in superconducting nanowires with a low-Ohmic environment

2012

In a number of recent experiments it has been demonstrated that in ultra-narrow superconducting channels quantum fluctuations of the order parameter, alternatively called quantum phase slips, are responsible for the finite resistance well below the critical temperature. The acceptable agreement between those experiments and the models describing quantum fluctuations in quasi-one-dimensional superconductors has been established. However the very concept of the phase slip is justified when these fluctuations are the relatively rare events, meaning that the effective resistance of the system should be much smaller than the normal state equivalent. In this paper we study the limit of the strong…

Ag/(Bi, Pb)-Sr-Ca-Cu-O superconducting tape processing: Solid state chemistry aspects

1993

Abstract Different preparation methods have been used to obtain starting powders used in the fabrication of composite tapes by the powder-in-tube method. The effect of these distinct starting powders on the superconducting properties of Ag/Bi-Sr-Ca-Cu-O monofilament tapes has been investigated. The changes in the physical properties, including the critical current density at 77 K and ac magnetic susceptibility, and microstructure, using optical and electronic microscopy, have been analyzed in relation to the solid state reactions involved in the Bi 2 Sr 2 CaCu 2 O 8+δ and Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ phase transformations.

Field-induced suppression of the pi-band superconductivity and magnetic hysteresis in the microwave surface resistance of MgB_2 at temperatures near …

2009

We report on the magnetic-field-induced variations of the microwave surface resistance, R_s, in a polycrystalline MgB_2 sample, at different values of temperature. We have detected a magnetic hysteresis in R_s, which exhibits an unexpected plateau on decreasing the DC magnetic field below a certain value. In particular, at temperatures near T_c the hysteresis manifests itself only through the presence of the plateau. Although we do not quantitatively justify the anomalous shape of the magnetic hysteresis, we show that the results obtained in the reversible region of the R_s(H) curve can be quite well accounted for by supposing that, in this range of magnetic field, the pi-gap is almost supp…

Self-assembled dimers with supramolecular chirality

2003

The possibilities to form dimeric capsules with supramolecular chirality from tetraurea calix[4]arenes composed of two different phenolic urea units are discussed in general and demonstrated experimentally for various selected examples.

Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts

2006

Abstract Significant progress has already been achieved in green manufacturing including dry and hard, often high-speed, machining technologies. For instance, the demand for higher productivity has resulted in the wider application of ceramic and PCBN tools with special multi-radii (wiper) geometry. This paper reports some important characteristics of the surface roughness produced in the turning of a hardened low-chromium alloy steel using mixed alumina–titanium carbon (TiC) ceramic cutting tools equipped with both conventional and wiper inserts. The characteristic geometrical features of surfaces obtained in both these turning operations have been assessed by means of representative two-d…