Search results for "Computer Hardware"
showing 10 items of 378 documents
High resolution Time of Flight determination based on reconfigurable logic devices for future PET/MR systems
2013
Abstract This contribution shows how to perform Time of Flight (TOF) measurements in PET systems using low-cost Field Programmable Gate Array (FPGA) devices with a resolution better of 100 ps. This is achieved with a proper management of the FPGA internal resources and with an extremely careful device calibration process including both temperature and voltage compensation. Preliminary results are reported.
A portable telescope based on the ALIBAVA system for test beam studies
2013
Abstract A test beam telescope has been built using the ALIBAVA system to drive its data acquisition. The basic telescope planes consist of four XYT stations. Each station is built from a detector board with two strip sensors, mounted one in each side (strips crossing at 90°). The ensemble is coupled to an ALIBAVA daughter board. These stations act as reference frame and allow a precise track reconstruction. The system is triggered by the coincidence signal of the two scintillators located up and down stream. The telescope can hold several devices under tests. Each ALIBAVA daughter board is linked to its corresponding mother board. The system can hold up to 16 mother boards. A master board …
The ATLAS tile calorimeter ROD injector and multiplexer board
2011
Abstract The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board call…
An upgraded ATLAS central trigger for 2015 luminosities
2013
The Central Trigger Processor (CTP) is a core unit of the first of three levels that constitute the ATLAS trigger system. Based on information from calorimeter and muon trigger processors as well as from some additional systems it produces the level-1 trigger decision and prompts the read-out of the sub-detectors. The increase in luminosity at the LHC has pushed the CTP operation to its design limits. In order to still satisfy the physics goals of the experiment after the shutdown of the LHC of 2013/2014 the CTP will be upgraded during this period. This article discusses the current Central Trigger Processor, the motivation for the upgrade, and the changes foreseen to meet the requirements …
FRAM—The Robotic Telescope for the Monitoring of the Wavelength Dependence of the Extinction: Description of Hardware, Data Analysis, and Results
2010
FRAM-F/(Ph)otometric Robotic Atmospheric Monitor is one of the atmospheric monitoring instruments at the Pierre Auger Observatory in Argentina. FRAM is an optical telescope equipped with CCD cameras and photometer, and it automatically observes a set of selected standard stars. Primarily, FRAM observations are used to obtain the wavelength dependence of the light extinction. FRAM telescope is also able to observe secondary astronomical targets, and namely the detection of optical counterparts of gamma-ray bursts has already proven to be successful. Finally, a wide-field CCD camera of FRAM can be used for rapid monitoring of atmospheric conditions along the track of particularly interesting …
Design and implementation of electronics and data acquisition system for Ultra-Fast Flash Observatory
2013
The Ultra-Fast Flash Observatory (UFFO) Pathfinder for Gamma-Ray Bursts (GRBs) consists of two telescopes. The UFFO Burst Alert & Trigger Telescope (UBAT) handles the detection and localization of GRBs, and the Slewing Mirror Telescope (SMT) conducts the measurement of the UV/optical afterglow. UBAT is equipped with an X-ray detector, analog and digital signal readout electronics that detects X-rays from GRBs and determines the location. SMT is equipped with a stepping motor and the associated electronics to rotate the slewing mirror targeting the GRBs identified by UBAT. First the slewing mirror points to a GRB, then SMT obtains the optical image of the GRB using the intensified CCD an…
The Performance of Belle II Data Acquisition System in the First Physics Run
2019
The Belle II experiment is a new generation B-factory experiment at KEK in Japan aiming at the search for New Physics in a huge sample of B-meson dacays. The commissioning of the SuperKEKB accelerator was started in 2017 (Phase 1), and then a pilot run with outer detectors was performed in 2018 (Phase 2). From March this year, an operation with the full detector has been started for the physics data taking (Phase 3). The Belle II data acquisiton system (DAQ) is now fully working in the Phase 3 run. The system consists of the trigger timing distribution system, the common readout modules (COPPER) with the unified optical data link to the detector front end, the readout PCs and the network sw…
ADVANCED STATISTICAL ANALYSIS OF LOCAL BUBBLE SIZE DISTRIBUTIONS IN 2D GAS FLUIDIZED BEDS
2009
The principal difficulty in analysing fluidization quality and bubble dynamics is related to the possibility of measuring or predicting the physical and geometrical properties of gas bubbles rising in a granular medium. Even the development of detailed experimental correlations gives poor results, being necessary a fully statistical approach. On the above basis, the present work focuses on the statistical analysis of the behaviour of a 2-D fluidized bed operating under bubbling and slugging conditions, performing measurements of Local Bubble Size Distributions (BSD) along the bed. The analysis allowed to observe a characteristic bimodal shape of BSDs for different particles dimension and fl…
Synchronization of the distributed readout frontend electronics of the Baby MIND detector
2017
Baby MIND is a new downstream muon range detector for the WGASCI experiment. This article discusses the distributed readout system and its timing requirements. The paper presents the design of the synchronization subsystem and the results of its test.