Search results for "Computer Science Applications"
showing 10 items of 3993 documents
Heat transfer in semi-transparent materials during laser interaction
2004
Abstract A model of energy exchange, based on the finite element method is specially developed to determine the thermal field for semi-transparent polymers irradiated by laser. Our model, which uses the finite element method, allows to define the laser and specific structure characteristics in terms of density of power, speed and shape of the spotlight, material coefficient absorption, etc. The model has been experimentally validated by measuring the thermal response induced by the laser source. The experimental part of the study has been performed using a semiconductor laser diode source and an infrared thermography camera.
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
A microstructural model for homogenisation and cracking of piezoelectric polycrystals
2019
Abstract An original three-dimensional generalised micro-electro-mechanical model for computational homogenisation and analysis of degradation and micro-cracking of piezoelectric polycrystalline materials is proposed in this study. The model is developed starting from a generalised electro-mechanical boundary integral representation of the micro-structural problem for the individual bulk grains and a generalised cohesive formulation is employed for studying intergranular micro-damage initiation and evolution into intergranular micro-cracks. To capture the electro-mechanical coupling at the evolving damaging intergranular interfaces, standard mechanical cohesive laws are enriched with suitab…
Mode I failure modeling of friction stir welding joints
2008
This paper analyzes mechanical response by finite element method up to the decohesion failure in fracture mode I for joints of friction stir welding (FSW) of an aluminum alloy. It first describes experimental investigations on specimens with FSW embedded, subjected to uniform traction and local punch tests used to characterize local elastic and plastic material parameters. The heterogeneity of the mechanical properties induced by the FSW process is taken into account for the elastic-plastic finite element simulation. The growing damage and the opening failure of the welding zone are described by the adoption of a cohesive interface model with specific mechanical properties.
Comparative assessment of surface roughness produced by hard machining with mixed ceramic tools including 2D and 3D analysis
2005
Abstract This paper provides a new comprehensive analysis of part surface finish in continuous dry turning of a hardened construction steel when using mixed alumina cutting tools. Consequently, the surface profiles (2D arragement) and surface microstereometries (3D arragement) generated during different hard part turning operations on a 40H low chromium alloy steel (equivalent to AISI 5140 or DIN 41Cr4), heat treated to the hardness of about 60 HRC, were evaluated. As a result, this paper aggregates the multi-parameters characterization of the surface roughness with the machined surface structure obtained at the three selected feed rates and constant cutting speed of 100 m/min. Results show…
Computer simulation of metal flow in the hot upsetting of a high-strength aluminium alloy
1993
Abstract The effects of metal-working temperature on the hot axisymmetric upsetting of AA 7012 aluminium alloy were investigated in the temperature range of from 250 to 400°C, at a strain rate of 4 s −1 . The material behaviour was studied by means of simulative methods based on the analysis of torsion-test results which have shown that when the strain increases, the flow stress increases to a peak value and then decreases to a fracture value. Furthermore, the flow stress decreases with decreasing strain rate and with increasing temperature. Constitutive equations, describing accurately the hot deformation behaviour of the material, were defined and used subsequently in a numerical model th…
On the influence of tool path in friction stir spot welding of aluminum alloys
2008
Abstract Friction stir spot welding (FSSW) has been proposed as an effective technology to spot weld the so-called “difficult to be welded” metal alloys. In the paper, a variation of the FSSW process has been considered. A tool path is given after the sinking phase nearby the initial penetration site; in this way a larger welding spot is obtained and more material is involved in the bonding process. The process mechanics of such modified FSSW process is highlighted and the joint strength undergoing tensile tests is considered at the varying both of the assigned tool path and of a few process parameters. Macro- and micro-analyses are made in order to analyze the local material microstructure…
On microstructural phenomena occurring in friction stir welding of aluminium alloys
2006
Abstract The results of experimental activity on friction stir welding (FSW) of aluminum alloys are reported. Butt joints of two different materials, namely AA2024-T4 and AA7075-T6, were investigated from a metallurgical point of view. Grain dimensions and insoluble particle densities were investigated both in the parent materials and in the joints. Furthermore, the effect of post-welding heat treatments on the joint strength was studied.
Improvement of flame spraying PEEK coating characteristics using lasers
2011
Flame spraying is frequently used for PEEK coatings elaboration on metallic surfaces. However, this process has a certain number of limitations particularly considering the quality of the coatings like high porosity or low interfacial adherence. For that reason a thermal post-processing is often necessary. From all of the processes which can be used (flame, oven, etc.), laser can be an interesting technology. Then, the aim of this study is to analyse the dependence of the morphological structure (compactness) and the adherence of the flame sprayed PEEK coatings to the stainless steel (304L) and aluminium alloy (AA2017) substrates on laser parameters. Moreover, the influence of the laser bea…
Multiphysical modeling of dissimilar welding via interlayer
2011
Abstract A multiphysical finite element modeling of dissimilar welding via interlayer material was proposed. A 2D model including heat transfer, fluid flow and level set problems allowed to simulate the morphology and the composition of melted zone in horizontal plane. The calculated thickness of melted interlayer was used as a main criterion for the choice of optimal welding conditions, when the chemical interaction between the joined materials must be avoided. A 1D diffusion model at the limit of melted zone allowed estimating the length and the composition of diffusion layer between one of the materials and the interlayer basing on previously calculated local temperature gradient. The si…