Search results for "Concentration effect"

Reduction of the interfacial tension between ‘immiscible’ polymers: to which phase one should add a compatibilizer

2001

Abstract The reduction of interfacial tension σ between polyethylene oxide (PEO) and polypropylene oxide (PPO) by either a triblock copolymer EO–PO–EO or a diblock copolymer styrene–EO was studied by means of the pendant drop method from 70 to 120°C. Time independent data correspond to stationary states and do not represent equilibrium information. The addition of the compatibilizer to the PPO phase is approximately twice as efficient as the addition to the PEO phase for both block copolymers. Knowing the concentration dependence of σ for one of the coexisting phases it is possible to forecast the effects resulting from the addition of the other phase by means of model considerations based …

Thermomechanical degradation of filled polypropylene

2003

The main problem in post-consumer plastics recycling is due to the thermomechanical stress acting on the melt during the reprocessing operations. The macromolecules break because of the temperature and of the mechanical stress. The extent of degradation is then correlated to the level of mechanical stress which, in turn, is proportional to the viscosity of the melt. The presence of fillers increases the viscosity of the polymers and then it is expected that the level of thermomechanical degradation of these systems is larger than that of the unfilled material. In this work the thermomechanical degradation kinetic of a polypropylene sample is investigated as a function of the calcium carbona…

Dynamics of Copolymer Micelles in a Homopolymer Melt:  Influence of the Matrix Molecular Weight

2000

We have studied the dynamics of styrene−isoprene (SI) block copolymer micelles in a matrix of linear entangled polyisoprene (PI) chains, using forced Rayleigh scattering (FRS) and dynamic mechanica...

1992

2H spin relaxation times, T1 and T2 and solid echo line shapes were investigated in 2-propanol (2-POH) solutions of poly(butyl methacrylate) (PBMA) in a wide concentration and temperature range, covering the solution, gel and glass states. From the results in deuterated 2-POH-d6 we found that the polymer influence upon solvent mobility is largely suppressed in the gel and glass states in contrast to normal polymer solutions where below the glass transition an increasing amount of solvent slows down with decreasing temperature. From 2H NMR of deuterated butyl side groups in the PBMA-d9/2-POH system we found that the side group motion is anisotropic and largely independent of solvent concentr…

Retention of carbaryl by polyether type polyurethane foam: a critical study

2000

This paper reports the retention of carbaryl by polyether type polyurethane foam in a dynamic mode. Several parameters that can influence the extraction of carbaryl from water samples were investigated such as concentration of carbaryl, mass of sorbent in the column, sample pH, saline concentration, solvent washing and sample flow rate. Results show that it is possible to achieve quantitative extractions when the sample flow rate is maintained up to 2.4 mL min−1, a mass of foam of 300 mg and a sample volume of 30 mL in 0.5 NaCl are employed. They also indicate that there is an ether-like solvent extraction mechanism controlling the sorption of the substance by the foam. Some recovery tests …

Reaction Rate Modeling in Cryoconcentrated Solutions: Alkaline Phosphatase Catalyzed DNPP Hydrolysis

2000

The hydrolysis of disodium p-nitrophenyl phosphate catalyzed by alkaline phosphatase was chosen as a model to study the kinetics of changes in frozen food products. The initial reaction rate was determined in concentrated sucrose solutions down to -24 degrees C, and the enzymatic characteristics K(M) and V(max) were calculated. The experimental data were compared to the kinetics predicted by assuming that the reaction was viscosity dependent. Indeed, an analysis of the enzymatic reaction demonstrated that both the diffusion of the substrate and the flexibility of the enzyme segments were controlled by the high viscosity of the media. When the temperature was too low for the viscosity to be …

Film blowing of silane-modified polyethylene

2009

The grafting of vinyltriethoxysilane (VTES) onto polyethylene (PE) with the help of small amounts of peroxides was investigated to film-blow these modified materials. The degree of crosslinking was kept very low to achieve good melt processability and improved mechanical properties. The possibility of obtaining modified PE films with improved properties and regularly distributed crosslinking with a single processing step demonstrates the uniqueness of this study. The additive concentration was established through preliminary studies; with a batch mixer, it was possible to process the modified PE in the film-blowing operation. Water treatment of the modified films after film blowing allowed …

Solution properties of polyelectrolytes—V. Viscometric study of mixed polyanions in pure water

1990

Abstract A viscometric study of sodium polystyrene sulphonate (NaPSS) and sodium poly( l -glutamate) (NaPLG) in salt-free water has been carried out as a function of the total concentration, cm, and the concentration of one polyelectrolyte at fixed concentration of the other. The influences of the molecular weight and concentration are considered in order to establish the degree of compatibility. For the first time, an equation is proposed to define the reduced viscosity of the NaPSS + NaPLG mixture in water. The viscometric interaction parameter, Bm, taking into account the electrostatic and thermodynamic interactions between both polyions, is defined as a geometrical mean of the contribut…

Standard partial molar volumes of alcohols in aqueous dodecyltrimethylammonium bromide solutions

1990

Density measurements of water-dodecyltrimethylammonium bromide (DTAB)-alcohol ternary systems as a function of alcohol and surfactant concentrations were carried out at 25°C. The alcohols were propanol (PrOH), 2-propanol (2-PrOH) and hexanol (HexOH). The apparent molar volume Vϕ,R of alcohols have been calculated and the standard (infinite dilution) partial molar volumes of alcohols V R at each surfactant concentration were obtained by means of a least squares fit of Vϕ,R vs. the alcohol concentration. The V R vs. surfactant concentration curves have been rationalized in terms of the partial molar volume of alcohol in the aqueous V f and the micellar V b phases and the distribution constant…

Heat capacities and volumes of suspensions in the presence of surfactants

2004

Abstract Density and heat capacity measurements of water–surfactant–silica ternary systems were carried out as functions of the silica and the surfactant concentrations at 298 K. From these properties, the apparent molar volume and heat capacity of the surfactant in a given water+silica mixture were evaluated. As well, the apparent specific volume and heat capacity of silica, at a given concentration, in the water+surfactant mixtures as functions of the surfactant concentration were calculated. Some surfactants (decyltrimethylammonium bromide, sodium octanoate, sodium decanoate, sodium dodecanoate, sodium decylsulfate, sodium perfluorooctanoate and N , N -dimethyldodecylamine- N -oxide) wer…