Search results for "Conversion coating"

Two-Dimensional Assembling of (2,2‘-Bipyrimidine)bis(oxalato)chromate(III) Units through Alkaline Cations

1999

Self-assembling of the tris-chelated [Cr(bpm)(ox)2]- complex with Na+ in aqueous solution leads to the remarkable bimetallic honeycomb layered compound of formula [NaICrIII(bpm)(ox)2]·5H2O (2) (bpm...

Influence of post-treatment time of trivalent chromium protection coating on aluminium alloy 2024-T3 on improved corrosion resistance

2019

Abstract Low corrosion protection performances of Trivalent Chromium Process (TCP) coatings with reference to Chromium Conversion Coatings (CCC) deposited on aluminium alloys can be overcome by application of post-treatment processes. This work shows the effect of post-treatment bath (containing hydrogen peroxide and lanthanum salt) on the chemical composition, structure and the corrosion performances of TCP coating deposited on AA 2024-T3 aluminium alloy. Different times of post-treatment bath were applied on the TCP coating and the samples were analyzed by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS), X-ray Photoelectron Spectroscopy (XPS) and Glow Discharge-Optical Emission …

2017

Abstract Chromic acid anodizing is important for the corrosion protection of aerospace aluminium alloys. Previous study has demonstrated that SO 4 2 − impurity in the chromic acid affects the film growth on aluminium at a voltage of 100 V. The present work further investigates aluminium and extends the study to industrial anodizing conditions (Bengough-Stuart (B-S) process) and to the AA 2024-T3 alloy. It is shown that SO 4 2 − concentrations between ~ 38–300 ppm reduce the film growth rate for aluminium anodized at 100 V in comparison with an electrolyte than contains ≤ 1.5 ppm SO 4 2 − , whereas ~ 1500–3000 ppm SO 4 2 have an opposite effect and lead to an unstable pore diameter. Under th…

Preparation of mixed oxides MNdO3, with M=Cr, Fe. Comparison of several methods

1993

Abstract Different methods for the formation of NdCrO3 and NdFeO3, having the perovskite-like structure, were studied including the ceramic method, simultaneous precipitation of hydroxides and simultaneous crystallization from aqueous solutions of nitrates. Preparation of mixed oxides from hydroxides simultaneously precipitated lowered the temperature and time required for their formation. In the case of NdCrO3 the formation process from hydroxides and nitrates occurred through the chromate, NdCrO4, without intermediate decomposition of the precursor to metal oxides, which lead to the mixed oxide by 600°C.

Improvement of the electrochemical behaviour of Zn-electroplated steel using regenerated Cr(III) passivation baths

2014

[EN] Conversion coatings based on trivalent chromium are more sensitive to the presence of zinc and iron impurities than the chromate formulations. This fact contributes to a decrease in the quality of passivation and to the generation of a significant amount of hazardous liquid waste. Recently, a new eco-innovative process based on Emulsion Pertraction Technology (EPT) is being implemented at industrial scale for selectively removing Zn and Fe from spent passivation baths in order to enhance the lifetime of the Cr (III) baths. In this study, the effect of Zn and Fe removal on the electrochemical behaviour of Zn-electroplated steel samples was evaluated by means of polarisation curves and e…

Magnetic and magneto-optical properties of nickel hexacyanoferrate/chromate thin films

2017

One of the most important challenges of modern science and technology is the quest for novel and tuneable materials, the properties of which can be widely controlled by chemical modifications or external stimuli. Simultaneously, an interest in the development of magnetic thin films also gains significant attention. In the current paper we bring together both these challenges and present a study of a new type of low-dimensional nickel hexacyanoferrate/chromate system. Thin films were obtained by the "layer by layer" deposition technique, where the ratio of Fe/Cr was controlled by the dipping sequence. The scope of this work is a comprehensive analysis of structural, spectroscopic and magneti…

Corrosion protection of Nd–Fe–B type permanent magnets by zinc phosphate surface conversion coatings

2001

Abstract The use of protective zinc phosphate top coatings to protect Nd–Fe–B type permanent magnets against corrosion is discussed. The progress of the phosphatisation process has been tested by simultaneous measurement of pH near surface, corrosion potential, substrate mass loss and phosphate coating mass gain. The corrosion behaviour of the magnet in phosphate solution was analyzed by the anodic polarization technique and the general resistance of the magnet to corrosion was evaluated by the Akimov drop test. It is shown that immersion of the magnet in the acidified (pH=2) phosphating solution containing Zn(II), nitrate and fluoride ions resulted in the formation of well adhered, thin an…

Corrosion resistance of the vacuum arc deposited Ti, TiN and TiO2 coatings on large area glass substrates

2000

An industrial installation for vacuum arc deposition is presented. Its potential in the field of decorative coatings for large area glass sheets is demonstrated. In particular it is possible to deposit patterned coatings through a polymeric textile mask. The ability to deposit uniform multilayer coatings having interference colours onto large silicate glass sheets is shown. Titanium, titanium nitride and titanium dioxide coatings on silicate glass have been characterized in terms of composition and corrosion resistance. Depth profiling was achieved with the aid of Auger electron spectroscopy. The corrosion resistance of TiN coatings is higher than that of TiO 2 . The corrosion resistance of…

Mobility of Cr and V in Spent Oil Shale: Impact of Thermal Treatment

2013

Abstract Spent oil shale samples were evaluated for potential chromium and vanadium release upon aerobic combustion used in power generation, or anaerobic retorting used in shale oil recovery. Combusted samples released more Cr than retorted or raw samples due to chromate formation. The behavior of vanadium was just opposite in that more V was released from retorted than from aerobically combusted samples, probably due to reduced vanadyl cation formation.

Structural Analysis and Photocurrent Spectroscopy of CCCs on 99.99% Aluminum

2003

A characterization of chromate conversion coatings (CCCs) formed in the presence and in the absence of accelerator (ferroferricyanide redox couple) has been performed by various techniques (transmission electron microscopy, TEM, glow discharge optical emission spectrometry, GDOES, X-ray absorption near-end structure, XANES, and photon correlation spectroscopy). The results of a detailed investigation on morphological, compositional, and solid-state properties of freshly converted aluminum samples at different immersion times (30 s-90 min) are reported. The TEM and GDOES data suggest the presence of iron-cyanide species only in the external layer of CCC of nearly constant thickness. The XANE…