Search results for "Converter"
showing 10 items of 275 documents
A Temperature Dependent Non-Linear Inductor Model for a DC/DC Boost Converter
2018
This paper is focused on the use of non-linear inductors in DC/DC switching converters, as well as their behaviour due to changes in current and temperature. The model of an inductor is set up on the basis of experimental data, which are automatically acquired by a virtual instrument; from those data, a polynomial curve describing the inductance variations is obtained. The analysis of the converter, performed by including the proposed model, is validated by experimental tests.
Design of a neutron converter for fission studies at the IGISOL facility
2012
The upgraded IGISOL facility with JYFLTRAP, at the accelerator laboratory of the University of Jyvaskyla, has been supplied with a new cyclotron which will provide proton or deuteron beams of the order of 100 μA with up to 30 MeV energy. This makes it an ideal place for measurements of neutron-induced fission fragments from various actinides, in view of proposed future nuclear fuel cycles. In the present paper, some considerations for the design of a neutron converter, based on simulations with the Monte Carlo codes MCNPX and FLUKA, are described.
High-resolution multichannel Time-to-Digital Converter core implemented in FPGA for ToF measurements in SiPM-PET
2013
In this contribution, Coincidence Resolving Time (CRT) results with the developed multichannel FPGA-TDC are showed as a function of different configurations for both, the sensor bias voltage and the digitizer threshold. The dependence of the CRT with the sensor matrix temperature, the amount of SiPM active area and the crystal type are also analyzed. Preliminary measurements carried out with a crystal array of 2 mm pixel size and 10 mm height have shown time resolutions for the entire 144 SiPM two-detectors ensemble as good as 800 ps.
Performances of a three-phase five-level cascaded H-bridge inverter with phase shifted B-spline based modulation techniques
2017
This paper presents a novel study of the performances of a five-level three-phase Cascaded H-Bridge Multilevel Inverter with Phase Shifted B-Spline based modulation techniques. The study has been focused on the use of B-Spline functions as carrier signals in order to evaluate the performances of the converter in terms of harmonic content on the output voltage. In the first step of this analysis the THD% has been taken into account to compare the voltage waveforms. Interesting results have been found on the fundamental amplitude of the phase and line voltage. Moreover, harmonic spectra has been compared to evaluate the different harmonic distribution in the voltage waveforms. In this work th…
A sliding mass wave energy converter
2019
This paper presents a wave energy converter which is based on a sliding mass coupled to a linear generator. In order to maximize energy extraction, the stochastic features of the energy source has been included in the mathematical model of the system in order to satisfactorily tackle the problem. The results of several simulations are presented.
A compact system for high precision time measurements ( < 14 ps RMS) and integrated data acquisition for a large number of channels
2011
A high precision ( < 14 ps RMS time resolution) and high channel density ( ~ 256 channels) Time to Digital Converter (TDC) module (realized in FPGAs) with integrated DAQ is presented. The data is transported over up to 8 Gigabit-Ethernet or optical links with up to 3 Gb/s. Slow-Control information is transported over the same links. It can be attached directly to the detector, which allows the elimination of long cables and crate systems. The full 256 channel TDCs are expected to use approximately 30 W electrical power. The module size is 20 cm by 23 cm. Power is provided by a galvanically isolated 48 V low noise power supply. AddOn-boards adapt to the special needs of the detector to be re…
Digitaler Spektrumstabilisator für schnelle Analog-Digital-Konverter
1969
Abstract A versatile spectrum stabilizer is described, suitable for all ADC's with a digital parallel output and a pilot pulse at the end of the conversion. The stabilizer is especially developed for a 100 MHz ADC, but it is independent of the digitizing rate and the mode of conversion. The unit has a maximum cyclus time of 2 μsec and permits a parallel transfer rate of 500 kHz. The stabilizer corrects the effects of gain drift and is insensitive to statistical errors.
A Novel Computational Approach for Harmonic Mitigation in PV Systems with Single-Phase Five-Level CHBMI
2018
In this paper, a novel approach to low order harmonic mitigation in fundamental switching frequency modulation is proposed for high power photovoltaic (PV) applications, without trying to solve the cumbersome non-linear transcendental equations. The proposed method allows for mitigation of the first-five harmonics (third, fifth, seventh, ninth, and eleventh harmonics), to reduce the complexity of the required procedure and to allocate few computational resource in the Field Programmable Gate Array (FPGA) based control board. Therefore, the voltage waveform taken into account is different respect traditional voltage waveform. The same concept, known as “voltage cancelation”, used for single-…
Characterization of inductors in partial saturation for SMPS applications
2017
The exploitation of partially saturated inductors in Switching Mode Power Supply (SMPS) is a key strategy for reducing the size of SMPS and increasing their power density [1]. However an accurate characterization and modellization of each inductor is needed for a correct design and control of the SMPS [2]. Most of inductors' datasheets only indicate the nominal inductance at low current. Anyway, when the inductor is subjected to a higher current, the value of the inductance is lessened. Moreover, inductance meters often actuate their measurements at no or moderate DC bias. In this work we describe the realization of an automated test bench (Fig. 1) for characterizing an inductor under varia…
Power Quality Savings with Controlled Fault-Tolerant Power Converters
2011
Power quality is simply the interaction of electrical power with electrical equipments. If electrical equipments operate correctly and reliably without being damaged or stressed, a suitable level of power quality is assured. On the other hand, if the electrical equipment malfunctions, is unreliable, or is damaged during normal usage, power quality is poor and probably the economical loss could be preeminent over the technical one. In the scenario of the Distributed generation power quality issues will be more- over important because an higher dissemination of power conditioning equip- ment will be requested and this obviously will increase the sources of vulnera- bility for the electrical s…