Search results for "Converters"
showing 10 items of 140 documents
MATLAB Co-Simulation Tools for Power Supply Systems Design
2011
ion level. Circuit simulation software as Powersim PSIM and Orcad Pspice are the most common choice for circuit modelling. In (Basso, 2008), the design and simulation of switchmode power supplies is deeply analyzed and simulation tips in several environments are proposed. ASIC simulation and verification tools as Xilinx ISE/Modelsim or Aldec ActiveHDL are available to implement the digital controller by the VHDL or VERILOG source code. Since the interaction between subsystems is the most common source of faults, testing separately analog and digital subsystems by the means of different verification tools is a severe mistake. Matlab is a powerful simulation environment for mixed-mode systems…
Experimental study on B-spline-based modulation schemes applied in multilevel inverters for electric drive applications
2019
This work presents the design, simulation, and experimental validation of new B-Spline-based modulation techniques applied to a Multilevel Power Inverter (MPI), particularly focusing the attention on the harmonic content of the output voltages of the inverter. Simulation and experimental results are proposed and discussed, mainly describing the potential benefits, such as the increase of the multi-level operation of the converter, and drawbacks (low-order harmonics) related to the adoption of B-Spline functions for multilevel inverters applied in the field of electrical drives.
Power System Oscillations with Different Prevalence of Grid-Following and Grid-Forming Converters
2022
The oscillatory behaviour of the power system is an aspect that is significantly affected by the increasing integration of converter-based generation sources. Several works address the impact of non-synchronous generation on the operation of the system from different points of view, but only a few studies focus on power-frequency oscillations with a prevalence of generation sources interfaced through power electronics. A lack of research can be found in particular in the comparative analysis of the two main control strategies for power converters, namely grid-following and grid-forming. The article aims to contribute to this direction, starting from a theoretical analysis of the two control…
Experimental Investigation on the Performances of a Multilevel Inverter Using a Field Programmable Gate Array-Based Control System
2019
The Field Programmable Gate Array (FPGA) represents a valid solution for the design of control systems for inverters adopted in many industry applications, because of both its high flexibility of use and its high-performance with respect to other types of digital controllers. In this context, this paper presents an experimental investigation on the harmonic content of the voltages produced by a three-phase, five level cascaded H-Bridge Multilevel inverter with an FPGA-based control board, aiming also to evaluate the performance of the FPGA through the implementation of the main common modulation techniques and the comparison between simulation and experimental results. The control algorithm…
Thermal Stability of a DC/DC Converter with Inductor in Partial Saturation
2021
Inductors operated in quasi saturation in dc–dc converters allow reduction of the core size and realization costs; on the other hand, they imply an increase of dissipated power that can jeopardize the thermal stability of the converter. In this article, this issue is studied by a mathematical model able to represent both the inductor nonlinearity and its temperature dependence. The main losses, such as ohmic, skin effect and magnetic, are taken into account in the model. The inductor is characterized by a polynomial curve whose parameters are a function of the temperature. Finally, the whole converter is modeled and simulation results, obtained on a boost converter, are compared with experi…
A comparison of different DC-DC converters for energy storage management in nearly-Zero Energy Buildings
2020
In the recent years, there has been a notable interest towards renewable sources, energy saving and efficiency optimization, in order to reduce the damages brought by fine dust and greenhouse gases in terms of safety, health and environmental protection. In the building sector renewable sources and energy efficiency optimization are leading to a large scale employment of nearly-Zero Energy Buildings (n-ZEBs), meaning that the balance between produced and required energy is negligible. For a proper n-ZEB implementation, a power system architecture has to be accurately designed, according to the existing renewable sources, loads and storage systems. In this paper, an investigation on differen…
Power Density Optimization of EMI Filters for Power Electronic Converters
The switching power converters are used in a broad variety of applications, from the consumer electronics to the DC distribution systems, from the vehicle applications (road vehicles, marine vehicles, aircraft) to the industrial automation. In each of these application fields, the conversion systems which present more compact size and reduced weight, at the same power, are strongly required in relation to stringent design constraints. In this context, the optimization of the power density of the converter becomes an essential requirement. The increase of the switching frequency of the static devices allows an improvement of the power density, thanks to the possibility of reducing the sizes …
Analysis and design of bi-directional DC-DC converters for ultracapacitors management in EVs
2018
The on-board energy-storage system of an electric vehicle (EV) should be able to collect large amounts of energy and to deal with fast load variations. The use of hybrid power sources as storage devices is an attractive solution, aiming at maximizing both energy and power density. The battery/ultracapacitors (UCs) combination promises to provide significant benefits. An accurate design of bi-directional converters, capable of proplery managing the charge/discharge of the UCs from/to a voltage bus, is essential. In this paper, a bi-directional DC-DC converter connected to a bank of UCs is described and the simulation results are given as well. The designed converter is a buck-boost type, abl…
Experimental Validation of a Novel Method for Harmonic Mitigation for a Three-Phase Five-Level Cascaded H-Bridges Inverter
2019
In modern high-power electrical drives, the efficiency of the system is a crucial constraint. Moreover, the efficiency of power converters plays a fundamental role in modern applications requiring also a limited weight, such as the electric vehicles and novel more electric aircraft. The reduction of losses pushes for systems with a dc bus and a high number of dc/ac converters, widespread in the vehicle, not burdened by a too expensive data processing system. The purpose of this article is to concur to reduce losses by proposing an innovative selective harmonic mitigation method based on the identification of the working areas where the reference harmonics present lower amplitudes. In partic…
Switching Capacitors Transformerless Bidirectional DC-DC Converter
2020
This paper presents an innovative converter topology that better connects the needs of the battery pack and the electric motor towards the validation of an eco-sustainable electric mobility model. More in particular, the components of the proposed converter change their connection state during both the charging and discharging time of the battery, leading to a higher performance with respect to traditional step-down or step-up converters. The simulations carried out by means of the PLECS® environment have demonstrated the early feasibility of the proposed system.