Search results for "Cyclin"
showing 10 items of 1021 documents
Formulation, Characterization and Optimization of the Processing Conditions of Blends of Recycled Polyethylene and Ground Tyre Rubbers: Mechanical an…
2005
Abstract Recycling represents a valid alternative to the disposal of post-consumer plastics in common landfills if it is possible to obtain new materials with good final properties compatible with practical application and, above all, by using cheap methods. In this work the possibility to produce secondary materials by blending recycled polyethylene (RPE) coming from greenhouses and post-consumer ground tyre rubber (GTR) has been studied. In particular, the preparation of these blends has been carried out in a common industrial twin screw extruder. RPE pellets and GTR powder were fed to the extruder without any other additive. Temperature, processing speed, mixing procedure and composition…
Structure-properties relationships in melt reprocessed PLA/hydrotalcites nanocomposites
2017
In this work the effect of multiple reprocessing was studied on molecular structure, morphology and properties of poly(lactic acid)/hydrotalcites (PLA/HT) nanocomposites compared to neat PLA. In addition, the influence of two different kinds of HT – organically modified (OM-HT) and unmodified (U-HT) – was evaluated. Thermo-mechanical degradation was induced by means of five subsequent extrusion cycles. The performance of the recycled materials was investigated by mechanical and rheological tests, differential scanning calorimetry (DSC), intrinsic viscosity measurements and SEM observation. The results indicated that the best morphology was achieved in the systems incorporating OM-HT. On inc…
Reprocessing of PLA/graphene nanoplatelets nanocomposites
2017
This work reports a study on the effect of multiple reprocessing on the properties of poly(lactic acid) (PLA) filled with graphene nanoplatelets (GnP) compared to the melt reprocessed neat polymeric matrix. In particular, morphological, X-Ray Diffraction and Micro-Raman analyses, intrinsic viscosity measurements, thermal, rheological and mechanical tests were carried out on materials reprocessed up five times by means of a single screw extruder. The results indicated that the presence of GnP decreased the degradation rate as a function of the reprocessing cycles in comparison with the neat PLA that, on the contrary, showed a more drastic reduction of the molecular weight. Moreover, the repr…
Material valorisation of amorphous polylactide. Influence of thermo-mechanical degradation on the morphology, segmental dynamics, thermal and mechani…
2012
[EN] This paper reports the effects of multiple mechanical recycling on the structure and properties of amorphous polylactide (PLA). The influence of the thermo-mechanical degradation induced by means of five successive injection cycles was initially addressed in terms of macroscopic mechanical properties and surface modification. A deeper inspection on the structure and morphology of PLA was associated to the thermal properties and viscoelastic behaviour. Although FT-IR analysis did not show significant changes in functional groups, a remarkable reduction in molar mass was found by viscometry. PLA remained amorphous throughout the reprocessing cycles, but the occurrence of a cold-crystalli…
Mechanical properties of pultruded glass fiber reinforced plastic after freeze–thaw cycling
2012
The use of pultruded fiber-reinforced plastics in civil infrastructure requires the long-term prediction of their mechanical properties, which should be based on understanding and estimating the processes in the structure under action of aggressive environmental factors: humidity and freeze–thaw cycles. This article reports on results of short-term exposure to severe freeze–thaw cycling in the temperature range from –30°C to 20°C of polyester-based glass fiber reinforced plastic both dry and wet. The effect of freeze–thaw cycling of flat specimens cut from I-beam pultruded profile was estimated by use of three-point-bending tests and dilatometric investigation in the temperature range from…
Degradation and Recycling of Films Based on Biodegradable Polymers: A Short Review
2019
The environmental performance of biodegradable materials has attracted attention from the academic and the industrial research over the recent years. Currently, degradation behavior and possible recyclability features, as well as actual recycling paths of such systems, are crucial to give them both durability and eco-sustainability. This paper presents a review of the degradation behaviour of biodegradable polymers and related composites, with particular concern for multi-layer films. The processing of biodegradable polymeric films and the manufacturing and properties of multilayer films based on biodegradable polymers will be discussed. The results and data collected show that: poly-lactic…
Physical properties of virgin-recycled ABS blends: Effect of post-consumer content and of reprocessing cycles
2012
Abstract Virgin/post-consumer ABS (pc-ABS) blends were re-processed and re-formed up to three times. The effect of pc-ABS content and of reprocessing cycles on the physical properties of the prepared blends was evaluated by mechanical tests (tensile, flexural and impact tests) and by rheological and thermo-mechanical measurements. The processability of pc-ABS blends was not substantially different by that of virgin ABS up to two recycling steps even if the third one induced a slightly decrease of viscosity, more remarkable on increasing the pc-ABS content. The mechanical and thermo-mechanical properties of the samples worsened on increasing the level of pc-ABS and after each reprocessing op…
Recycling of a Biodegradable Polymer Blend
2020
Mechanical recycling is one of the possible ways to enhance the value of postconsumer plastic materials. However, the final performance of the recycled material will strongly depend on the quality of the selection made on the recycled product and on the degradation of the properties. In this context, the present study examines the effect of reprocessing for five successive extrusion cycles on the rheological, mechanical and thermal properties of a poly(butylene adipate-co-terephthalate) (PBAT)-based blend on samples reprocessed in both dry and wet conditions. The results showed that when the sample was processed after drying, degradation of the material was less than when it was processed i…
Dielectric Spectroscopy of Recycled Polylactide
2014
The effects of multiple mechanical recycling on amorphous polylactide (PLA) were simulated by means of five successive injection-grinding cycles. The influence of the induced thermo-mechanical degradation on the dielectric properties of PLA was analysed. The relaxation spectra were studied in terms of the complex dielectric permittivity (ε0 and ε00) and the dielectric loss tangent, tg(d) in the frequency range from 102 to 107 Hz over the temperature interval from 0 C to 140 C. It was possible to distinguish two relaxations zones, one at low temperatures and high frequencies (b relaxation) and another at higher temperatures and lower frequencies (a relaxation). The individual relaxations wer…
Matrix and Filler Recycling of Carbon and Glass Fiber-Reinforced Polymer Composites: A Review
2021
Fiber-reinforced polymers (FRPs) are low-density, high-performance composite materials, which find important applications in the automotive, aerospace, and energy industry, to only cite a few. With the increasing concerns about sustainability and environment risks, the problem of the recycling of such complex composite systems has been emerging in politics, industry, and academia. The issue is exacerbated by the increased use of FRPs in the automotive industry and by the expected decommissioning of airplanes and wind turbines amounting to thousands of metric tons of composite materials. Currently, the recycling of FRPs downcycles the entire composite to some form of reinforcement material (…