Search results for "Cylinder"

Permanent magnet bottom-stirred swirling flow in coaxial shallow cylindrical containers

2021

Here, an original rotating permanent magnet (RPM) system placed coaxially with the liquid metal container is studied as an effective means of generating flow in shallow cylinders for potential application in aluminum metallurgy (e.g., for ladle stirring and metal dosing). The studied RPM system generates volume force with strong axial variation and force maximum near the radial midpoint. The numerical and experimental data show that, in the shallow cylinder case, the azimuthal velocity follows the force radial distribution. The resulting velocity maximum occurs near the radial midpoint, unlike in the traditional rotating magnetic field (RMF) stirrer systems, where the velocity maximum occur…

CFD prediction of shell-side flow and mass transfer in regular fiber arrays

2021

Numerical simulations were conducted for fully developed, steady-state flow with mass transfer in fiber bundles arranged in regular lattices. The porosity was 0.5 and the Schmidt number 500. Several combinations of axial flow, transverse flow and flow attack angles in the cross-section plane were considered. The axial and transverse Reynolds numbers Rez , ReT were made to vary from 10(^−4) to 10(^2). Concentration boundary conditions, and the definition of an average Sherwood number, were addressed. Results for the hydraulic permeability were compared with the literature. Both hexagonal and square lattices were found to be hydraulically almost isotropic up to transverse flow Reynolds number…

Rotating magnetic dipole-driven flows in a conducting liquid cylinder

2021

Four configurations of a rotating magnetic dipole-driven turbulent flow in an electrically conducting liquid cylinder are considered by spectral direct numerical simulation. These configurations differ by parallel or perpendicular orientation of the dipole rotation vector with respect to the nearest surface of the cylinder or its axis. The rotating dipole generates electromagnetic force in a thin outer liquid layer facing it. A concentrated vortex is driven when the dipole rotation vector is perpendicular to the nearest surface. This vortex closely resembles the rotating disk-driven flow. When the dipole rotation vector is parallel to the nearest surface, then a distributed vortex occurs ak…

Extended fractional-order Jeffreys model of viscoelastic hydraulic cylinder

2020

A novel modeling approach for viscoelastic hydraulic cylinders, with negligible inertial forces, is proposed, based on the extended fractional-order Jeffreys model. Analysis and physical reasoning for the parameter constraints and order of the fractional derivatives are provided. Comparison between the measured and computed frequency response functions and time domain transient response argues in favor of the proposed four-parameter fractional-order model.

The Bethe ansatz and the Tzitzéica–Bullough–Dodd equation

2012

The theory of classically integrable nonlinear wave equations, and the Bethe Ansatz systems describing massive quantum field theories defined on an infinite cylinder, are related by an important mathematical correspondence that still lacks a satisfactory physical interpretation. In this paper we shall describe this link for the case of the classical and quantum versions of the (Tzitz\'eica-)Bullough-Dodd model.

Zero rest-mass fields and the Newman-Penrose constants on flat space

2020

Zero rest-mass fields of spin 1 (the electromagnetic field) and spin 2 propagating on flat space and their corresponding Newman-Penrose (NP) constants are studied near spatial infinity. The aim of this analysis is to clarify the correspondence between data for these fields on a spacelike hypersurface and the value of their corresponding NP constants at future and past null infinity. To do so, Friedrich's framework of the cylinder at spatial infinity is employed to show that, expanding the initial data in terms spherical harmonics and powers of the geodesic spatial distance $\rho$ to spatial infinity, the NP constants correspond to the data for the second highest possible spherical harmonic …

Global Linear Stability Analysis of the Flow Around a Superhydrophobic Circular Cylinder

2016

International audience; Over the last few years, superhydrophobic (SH) surfaces have been receiving an increasing attention in many scientific areas by virtue of their ability to enhance flow slip past solid walls and reduce the skin-friction drag. In the present study, a global linear-stability analysis is employed to investigate the influence of the SH-induced slip velocity on the primary instability of the 2D flow past a circular cylinder. The flow regions playing the role of 'wavemaker' are identified by considering the structural sensitivity of the unstable mode, thus highlighting the effect of slip on the global instability of the considered flow. In addition, a sensitivity analysis t…

On the Energy Efficiency of Dual Prime Mover Pump-Controlled Hydraulic Cylinders

2019

Abstract This paper concerns the energy efficiency of a special class of pump-controlled hydraulic cylinders utilizing two prime movers. The performance of such circuits has been studied previously motivated by their capability of providing an actuator stiffness similar to that of servo valve-controlled systems. This characteristic may improve performance and robustness in applications requiring feedback control. In this paper, the presence of losses similar to that of fluid throttling, in the sense that they occur even in the absence of component inefficiencies, are demonstrated for such circuits and shown to degrade the overall energy efficiency of the system. The conditions under which s…

Controlling a Negative Loaded Hydraulic Cylinder using Pressure Feedback

2010

Lead-Lag-Shaped Interactive Force Estimation by Equivalent Output Injection of Sliding-Mode

2020

Estimation of interactive forces, which are mostly unavailable for direct measurement on the interface between a system and its environment, is an essential task in various motion control applications. This paper proposes an interactive force estimation method, based on the well-known equivalent output injection of the second-order sliding mode. The equivalent output injection is used to obtain a frequency-unshaped quantity that appears as a matched external disturbance and encompasses the interactive forces. Afterwards, a universal lead-lag shaper, depending on dynamics of the motion control system coupled with its environment, is used to extract an interactive force quantity. Once identif…