Search results for "DRY"
showing 10 items of 980 documents
The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining
2012
Abstract This paper presents results of an experimental study of cryogenic machining of hardened AISI 52100 steel, focusing on surface integrity. Experiments were performed under dry and cryogenic cooling conditions using CBN tools varying cutting speeds, workpiece hardness and tool geometry. Surface integrity parameters (surface roughness, white layer thickness, residual stresses, metallurgical conditions including grain size, phase transformation, etc.) were investigated to establish the effects of cryogenic cooling on the surface integrity of the machined component, and results were compared with those from dry hard machining. Overall, cryogenic cooling provides improved surface integrit…
Influence of mode stirrer and air renewal on controlled microwave drying of sliced zucchini
2017
An on-line temperature-controlled microwave (MW) system, based on infrared thermography, was developed for drying zucchini slices. Moreover, the effects of different configurations, including turntable rotation, mode stirrer and air renewal, alone or in combination, on drying kinetics and quality of dried product were evaluated. The combination of stirrer and air renewal reduced the drying time of zucchini slices by about 48% with respect to the basic configuration and by 22% with respect to air renewal only. The lowest oscillation of temperatures about the fixed level (65 °C) was found when operating with the stirrer mode, because of the improved uniformity of the MW distribution. The sa…
Ceramic/metal nanocomposites by lyophilization: Processing and HRTEM study
2012
5 páginas, 8 figuras, 1 tabla.-- El pdf del artículo es el manuscrito de autor.
Ceramic/metal nanocomposites by lyophilization: Spark plasma sintering and hardness
2014
The present study is focused on the procedure of spray-drying and lyophilization techniques for the preparation of ceramic/metal nanocomposites. The results of the study at all stages are compared with those corresponding to powders conventionally dried by heating in furnace. Starting from aqueous solutions of metal salts and ceramic powders, the procedure follows with spray-drying, lyophilization, calcination of the resulting powders and subsequent Spark Plasma Sintering (SPS). X-ray diffraction analysis of the powders at different stages of the processing routes was used for phase indexing; further characterization was performed by Transmission Electron Microscopy and Energy Dispersive X-…
Mechanical characterization of dry asphalt rubber concrete for base layers by means of the four bending points tests
2012
The mechanical characterisation of the asphalt concrete in terms of both the fatigue resistance and the stiffness modulus is necessary to use any design method of the flexible road pavements. Even more the determination of these mechanical properties is necessary if the asphalt concrete investigated is an innovative material as a dry asphalt rubber concrete DARC (i.e. a bituminous mixture with rubber via dry process). Such material is less known and investigated than the asphalt rubber concrete via wet process, even if its application implies peculiar economical and environmental advantages such as no specialized equipment or significant plant modifications and large quantity of recycled wa…
Laser densification of organic coating: Effects of laser wavelength, operating parameters and substrate properties
2012
International audience; Mechanical bonding and interface behaviour play a key role for any materials deposited on different substrates. Usually, a post-spray heat treatment is required to improve the coating morphology and to enhance mechanical properties of thermal-sprayed polymeric coating. The effects of YAG, CO2 and diode laser radiations on as-sprayed PEEK coating deposited on stainless steel and aluminum substrates were investigated. The results revealed a good coating densification and interface behavior. A correlation between coating and substrate absorption coefficients, their thermophysical properties and laser operating parameters was shown. Besides, the finite element modeling b…
Thioether-Bearing Hyperbranched Polyether Polyols with Methionine-Like Side-Chains: A Versatile Platform for Orthogonal Functionalization
2016
The synthesis of thioether-bearing hyperbranched polyether polyols based on an AB/AB2 type copolymerization (cyclic latent monomers) is introduced. The polymers are prepared by anionic ring-opening multibranching copolymerization of glycidol and 2-(methylthio)ethyl glycidyl ether (MTEGE), which is conveniently accessible in a single etherification step. Slow monomer addition provides control over molecular weights. Moderate dispersities (Đ = 1.48–1.85) are obtained, given the hyperbranched structure. In situ 1H NMR copolymerization kinetics reveal reactivity ratios of rG = 3.7 and rMTEGE = 0.27. Using slow monomer addition, copolymer composition can be systematically varied, allowing for th…
Transition to Reinforced State by Percolating Domains of Intercalated Brush-Modified Cellulose Nanocrystals and Poly(butadiene) in Cross-Linked Compo…
2013
The classic nanocomposite approach aims at percolation of low fraction of exfoliated individual reinforcing nanoscale elements within a polymeric matrix. By contrast, many of the mechanically excellent biological nanocomposites involve self-assembled and space-filled structures of hard reinforcing and soft toughening domains, with high weight fraction of reinforcements. Here we inspect a new concept toward mimicking such structures by studying whether percolation of intercalated domains consisting of alternating rigid and reinforcing, and soft rubbery domains could allow a transition to a reinforced state. Toward that, we present the functionalization of rigid native cellulose nanocrystals …
Applications of spray-drying in microencapsulation of food ingredients: An overview
2007
International audience; Spray-drying process has been used for decades to encapsulate food ingredients such as flavors, lipids, and carotenoids. During this drying process, the evaporation of solvent, that is most often water, is rapid and the entrapment of the interest compound occurs quasi-instantaneously. This required property imposes a strict screening of the encapsulating materials to be used in addition to an optimization of the operating conditions. Likewise, if the encapsulated compound is of hydrophobic nature, the stability of the feed emulsion before drying should also be considered. Thus, spray-drying microencapsulation process must rather be considered as an art than a science…
Using the simplified falling head technique to detect temporal changes in field-saturated hydraulic conductivity at the surface of a sandy loam soil
2007
Abstract Determining temporal changes in field-saturated hydraulic conductivity ( K fs ) is important for understanding and modeling hydrological phenomena at the field scale. Little is known about temporal variability of K fs values measured at permanent sampling points. In this investigation, the simplified falling head (SFH) technique was used for an approximately 2-year period to determine temporal changes in K fs at 11 permanent sampling points established at the surface of a sandy loam soil. Additional K fs measurements were obtained by the single-ring pressure infiltrometer (PI) technique to also compare the SFH and PI techniques. The lowest mean values of K fs , M ( K fs ), were det…