Search results for "Data acquisition"
showing 10 items of 237 documents
A security and surveillance application of the innovative Monitoring Underwater Buoy Systems (MUnBuS) on the Protected Marine Area (AMP) of capo gall…
2015
The proposed low cost systems shows the results obtained in the implementation and testing on real security application to Protected Marine Area surface and submarine environment of a innovative Monitoring Underwater Buoy Systems (MUnBuS) for installation with IR-CCTV-Cam, ultrasonic dolphin warning system and Green Laser Perimeter Detection. This concerning innovative Monitoring Underwater Buoy Systems that can be remotely controlled from the ground, air, satellite and sea and from a Center of Supervision Telecontroller And Data Acquisition and Monitoring (Mobile- STADAM Center). The Buoy is hosts for the radio or satellite communication equipment, the downloading and telemetering data equ…
Development of a high-accuracy PC-based wattmeter with commercial data acquisition boards
2011
This paper presents the development of a high accuracy sampling wattmeter, which makes use of two commercial data acquisition boards (DAQs) connected to a common personal computer. Commercial software is also used for data processing and implementation of the virtual instrument. The set up of the PC-based wattmeter is described and a preliminary evaluation of its metrological performances is made by means of two series of experimental tests, which were carried out with an electric power standard and a high performance multifunction calibrator. © 2011 IEEE.
A PC-based wattmeter for accurate measurements in sinusoidal and distorted conditions: Setup and experimental characterization
2012
This paper presents the development of a high-accuracy sampling wattmeter, which can be employed with both sinusoidal and distorted input signals. The proposed personal computer (PC)-based system is a simple, portable, and low-cost solution because it is based on two commercial data acquisition boards connected to a common PC. Owing to this solution, the voltage is sensed directly, avoiding expensive voltage dividers, while the current is sensed by means of a noninductive current shunt. Commercial software is also used for data processing and implementation of the virtual instrument. The setup of the PC-based wattmeter is described, with a detailed description of the correction strategy of …
Virtual Instruments: Uncertainty Evaluation in the Presence of Electromagnetic Interferences
2007
The electromagnetic interferences can influence the performances of a virtual instrument; consequently, in a generic measurement performed by using these instruments, the related uncertainty values can increase. In the paper, we report the results of various experimental tests performed with the aim to check if and how the radiated and/or conducted disturbances affect the instruments' characteristics and, in particular, the single uncertainty sources. Starting from these results and applying an already proposed method for the uncertainty estimation in the measurements performed by means of virtual instruments, it is possible to take into account and to evaluate the contribute of the electro…
New statistical post processing approach for precise fault and defect localization in TRI database acquired on complex VLSI
2013
International audience; Timing issue, missing or extra state transitions or unusual consumption can be detected and localized by Time Resolved Imaging (TRI) database analysis. Although, long test pattern can challenge this process. The number of photons to process rapidly increases and the acquisition time to have a good signal over noise ratio (SNR) can be prohibitive. As a result, the tracking of the defect emission signature inside a huge database can be quite complicated. In this paper, a method based on data mining techniques is suggested to help the TRI end user to have a good idea about where to start a deeper analysis of the integrated circuit, even with such complex databases.
Application of a new wireless instrument to characterize thermal properties of ground coupled heat exchangers
2010
Abstract In this work, we report the design and laboratory test of a new instrument to measure the temperature of the heat transfer fluid along the borehole exchanger (BHE) by autonomous wireless sensor. The instrument consists of a device, which inserts and extracts miniaturized wireless sensors in the borehole with a mechanical subsystem, composed by a circulating pump and two valves. This device transmits to the sensors the acquisition configuration, and downloads the temperature data measured by the sensor along its way through the borehole heat exchanger. Each sensor is included in a sphere of 25 mm diameter and contains a transceiver, a microcontroller, a temperature sensor and a powe…
Impact of industrial environments on the PC-based measurements
2007
In the paper we present a simple and fast procedure to evaluate the impact of the electromagnetic disturbances, which can be present in the industrial locations, on the measurements performed by a generic PC-based measurement instrument. The method is conceived starting from the data obtained by subjecting the instruments to the disturbances prescribed by the IEC-61326 standard. The results show that, even under heavy disturbances, the common good practices of shielding and grounding allow a correct employment of this kind of instrumentation.
Automated single ring infiltrometer with a low-cost microcontroller circuit
2015
Automation of a new single ring infiltrometer.Data acquisition system based on the open source microcontroller platform Arduino.New method to minimize the disturbance of the soil surface.New approach to process transducer output. A method to automate data collection with a compact infiltrometer under constant head conditions was developed. The infiltrometer consists of a containment ring with a small quasi-constant head of water (i.e., 2-3mm) that is controlled by a Mariotte reservoir and a data acquisition system based on the open source microcontroller platform Arduino and a differential pressure transducer. The presented design can be easily reproduced and operated.The infiltrometer was …
Design of a mezzanine card with bandwidth aggregation for HPGe gamma spectroscopy
2016
In experimental nuclear physics, HPGe segmented detectors are used to provide high energy resolution of the gamma rays. Besides, 4pi configuration is common to get a full coverage of the interaction point and detection of all the products of the collisions. In this type of experiments, the number of electronic channels can be high (>100) and also the sampling frequency of the digitizing system (>100 Msps). This results in a high data rate per channel (> 2 Gbps) and thus a high aggregated bandwidth to process. In principle, this problem can be solved using a parallel data acquisition system where the input channels (commonly arriving through optical fibers) are read and processed accordingly…
Design and characterization of the SiPM tracking system of NEXT-DEMO, a demonstrator prototype of the NEXT-100 experiment
2013
NEXT-100 experiment aims at searching the neutrinoless double-beta decay of the Xe-136 isotope using a TPC filled with a 100 kg of high-pressure gaseous xenon, with 90% isotopic enrichment. The experiment will take place at the Laboratorio Subterraneo de Canfranc (LSC), Spain. NEXT-100 uses electroluminescence (EL) technology for energy measurement with a resolution better than 1% FWHM. The gaseous xenon in the TPC additionally allows the tracks of the two beta particles to be recorded, which are expected to have a length of up to 30 cm at 10 bar pressure. The ability to record the topological signature of the beta beta 0 nu events provides a powerful background rejection factor for the bet…