Search results for "Divertor"
showing 10 items of 63 documents
Improved EDGE2D-EIRENE simulations of JET ITER-like wall L-mode discharges utilising poloidal VUV/visible spectral emission profiles
2015
A discrepancy in the divertor radiated powers between EDGE2D-EIRENE simulations, both with and without drifts, and JET-ILW experiments employing a set of NBI-heated L-mode discharges with step-wise density variation is investigated. Results from a VUV/visible poloidally scanning spectrometer are used together with bolometric measurements to determine the radiated power and its composition. The analysis shows the importance of D line radiation in contributing to the divertor radiated power, while contributions from D radiative recombination are smaller than expected. Simulations with W divertor plates underestimate the Be content in the divertor, since no allowance is made for Be previously …
Overview of the JET results with the ITER-like wall
2013
Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Zeff (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. T…
Tritium retention measurements by accelerator mass spectrometry and full combustion of W-coated and uncoated CFC tiles from the JET divertor
2016
Abstract Accelerator mass spectrometry (AMS) and the full combustion method (FCM) followed by liquid scintillation counting were applied to quantitatively determine the tritium retention in the tungsten-coated carbon fibre composites (CFC), in comparison to uncoated CFC tiles from the JET divertor. The tiles were adjacent and exposed to plasma operations between 2007 and 2009. The tritium depth profiles are showing that the tritium retention on the W-coated tile was reduced by a factor of 13.5 in comparison to the uncoated tile whereas the bulk tritium concentration is approximately the same for both tiles.
Applicability of the dielectric barrier discharge for helium ash measurements in the divertor region
2016
Abstract Controlled fusion based on the magnetic confinement of the plasma is one of the main aims of the Euro-fusion programme. In the fusion device, the hydrogen isotopes, in nuclear reactions, will produce helium nuclei. The products, as the ash, will be removed from the plasma in the region of the so-called divertor. Controlling the helium to hydrogen ratio in this ‘exhaust gas’ will provide information about the efficiency of the fusion process as well as of the efficiency of the helium removal system. One of the methods to perform this task is to study the properties of the discharge conducted in such exhaust gas. In this paper, the applicability of the dielectric barrier discharge (D…
Evolution of nitrogen concentration and ammonia production in N 2 -seeded H-mode discharges at ASDEX Upgrade
2019
Ammonia formation was studied in a series of dedicated nitrogen seeded H-mode discharges at ASDEX Upgrade. The evolution of ammonia formation was investigated with a reference phase before the seeding, and a long, stable flat-top nitrogen-seeded phase. It was monitored with divertor spectroscopy and analysis of the exhaust gas. The amount of the detected ammonia increased continuously over the course of five discharges with the same nitrogen seeding rate. The same trend was observed in the nitrogen density in the core plasma, as measured by charge exchange recombination spectroscopy and other signals, linked to the effects of nitrogen seeding. The results show that the rate of ammonia forma…
Overview of the DEMO staged design approach in Europe
2019
This paper describes the status of the pre-conceptual design activities in Europe to advance the technical basis of the design of a DEMOnstration Fusion Power Plant (DEMO) to come in operation around the middle of this century with the main aims of demonstrating the production of few hundred MWs of net electricity, the feasibility of operation with a closed-tritium fuel cycle, and maintenance systems capable of achieving adequate plant availability. This is expected to benefit as much as possible from the ITER experience, in terms of design, licensing, and construction. Emphasis is on an integrated design approach, based on system engineering, which provides a clear path for urgent R&D …
Hydraulic analysis of EU-DEMO divertor plasma facing components cooling circuit under nominal operating scenarios
2019
Within the framework of the Work Package DIV 1 – “Divertor Cassette Design and Integration” of the EUROfusion action, a research campaign has been jointly carried out by University of Palermo and ENEA to investigate the steady state thermal-hydraulic behaviour of the DEMO divertor cassette cooling circuit, focussing the attention on its Plasma Facing Components (PFCs). The research campaign has been carried out following a theoretical-computational approach based on the Finite Volume Method and adopting the commercial Computational Fluid-Dynamic code ANSYS-CFX. A realistic model of the PFCs cooling circuit has been analysed, specifically embedding each Plasma Facing Unit (PFU) cooling chann…
On the numerical assessment of the thermal-hydraulic operating map of the DEMO Divertor Plasma Facing Components cooling circuit
2020
Abstract Within the framework of the Work Package DIV 1 - “Divertor Cassette Design and Integration” of the EUROfusion action, a research campaign has been jointly carried out by University of Palermo and ENEA to investigate the thermal-hydraulic behaviour of the DEMO divertor cassette cooling system, focussing the attention on the 2018 configuration of the Plasma Facing Components (PFCs) circuit consistent with the DEMO baseline 2017. The research campaign has been carried out following a theoretical-computational approach based on the finite volume method and adopting the commercial Computational Fluid-Dynamic (CFD) code ANSYS CFX. A steady-state CFD analysis has been carried out for the …
On the thermal-hydraulic optimization of DEMO divertor plasma facing components cooling circuit
2018
Abstract Within the framework of the Work Package Divertor, Subproject: Cassette Design and Integration (WPDIV-Cassette) of the EUROfusion action, a research campaign has been jointly carried out by ENEA and University of Palermo to investigate the thermal-hydraulic performances of the DEMO divertor cassette cooling system. Attention has been focussed on the divertor Plasma Facing Components (PFCs) cooling circuit and a parametric analysis has been carried out in order to assess the potential impact of proper layout changes on its thermal-hydraulic performances, mainly in terms of coolant total pressure drop, flow velocity distribution and margin against critical heat flux occurrence. The r…
Hydraulic assessment of an upgraded pipework arrangement for the DEMO divertor plasma facing components cooling circuit
2021
Abstract In the context of the Work Package DIVertor (WPDIV) of the EUROfusion action, a research campaign has been carried out by University of Palermo in cooperation with ENEA to assess the thermal-hydraulic performances of the DEMO divertor cooling system, concentrating the attention on its 2019 Plasma Facing Components (PFCs) configuration, relevant to DEMO baseline 2017. The research activity has been performed following a theoretical-numerical technique based on the finite volume method and adopting the well-known ANSYS CFX CFD code. The PFCs cooling circuit thermal-hydraulic performances under nominal steady-state conditions, assessed mainly in terms of coolant total pressure drop, c…