Search results for "Drill"

El grado cero de lo social

1984

Comparison of conventional twist drill protocol and piezosurgery for implant insertion: an ex vivo study on different bone types.

2015

Objective The aim of this ex vivo study was to compare implant insertion procedures using piezosurgery and conventional drilling in different qualities of bone. Implant bed preparation time, generated heat, and primary implant stability were analyzed. Material and methods Fresh ex vivo porcine bone block samples (cancellous, mixed, and cortical bone) were obtained. The bone quality was quantified by ultrasound transmission velocity (UTV). Each bone sample received three implants of the same diameter using each of the techniques of piezosurgery and conventional twist drills. Time for preparation was taken and the temperature while performing the osteotomy was measured using infrared spectros…

NUMERICAL-EXPERIMENTAL METHOD FOR THE ANALYSIS OF RESIDUAL STRESSES IN COLD-EXPANDED HOLES

2012

Hole cold expansion is a technique widely used to improve the fatigue life of components with holes, e.g. bolted or riveted joints. As it has been demonstrated in literature by analytical, numerical and experimental analyses carried out by several authors, the compressive residual stresses introduced by the hole cold expansion have a beneficial influence on both the static and the fatigue strength of the treated component, because they reduce significantly the typical stress peaks around the hole due to stress concentration. In the literature, various analyses of the residual stresses introduced by the hole cold expansion have been performed by using several methods such as X-ray diffractio…

Measuring Inaccessible Residual Stresses Using Multiple Methods and Superposition

2010

The traditional contour method maps a single component of residual stress by cutting a body carefully in two and measuring the contour of the cut surface. The cut also exposes previously inaccessible regions of the body to residual stress measurement using a variety of other techniques, but the stresses have been changed by the relaxation after cutting. In this paper, it is shown that superposition of stresses measured post-cutting with results from the contour method analysis can determine the original (pre-cut) residual stresses. The general superposition theory using Bueckner’s principle is developed and limitations are discussed. The procedure is experimentally demonstrated by determini…

The formation of peak rings in large impact craters.

2016

The Chicxulub impact crater, known for its link to the demise of the dinosaurs, also provides an opportunity to study rocks from a large impact structure. Large impact craters have “peak rings” that define a complex crater morphology. Morgan et al. looked at rocks from a drilling expedition through the peak rings of the Chicxulub impact crater (see the Perspective by Barton). The drill cores have features consistent with a model that postulates that a single over-heightened central peak collapsed into the multiple-peak-ring structure. The validity of this model has implications for far-ranging subjects, from how giant impacts alter the climate on Earth to the morphology of crater-dominated …

Sedimentology of a profile from Etoliko Lagoon, Western Greece

2013

A key feature of Greece is the large amount of historical and archaeological records. The sedimentary record of the Etoliko Lagoon, Aetolia, Western Greece, offers an ideal opportunity to study human-environment interaction and to disentangle natural and anthropogenic imprints in the sedimentary record. By applying an interdisciplinary approach of combining geoscientific methods (XRF, LOI, grain size analysis) with archaeological and historical records, the 8.8 m long sedimentary sequence ETO1C reveals the palaeoenvironmental history of the lagoon and its catchment since 11,670 cal BP. With a thorough chronology based on 14C age-depth-modelling including varve counting, different evolutiona…

Isotopic, carbon and minor element composition of the Sancerre sediments (Jurassic, Paris Basin)

2017

One of the most elusive aspects of the Toarcian oceanic anoxic event (T-OAE) is the paradox between carbon isotopes that indicate intense global primary productivity and organic carbon burial at a global scale, and the delayed expression of anoxia in Europe. During the earliest Toarcian, no black shales were deposited in the European epicontinental seaways, and most organic carbon enrichment of the sediments postdated the end of the overarching positive trend in the carbon isotopes that characterises the T-OAE. In the present study, we have attempted to establish a sequence stratigraphic framework for Early Toarcian deposits recovered from a core drilled in the Paris Basin using a combinati…

Record of pollen, silt and greyscale stack from the Eifel Laminated Sediment Archive (ELSA)

2005

Investigating the processes that led to the end of the last interglacial period is relevant for understanding how our ongoing interglacial will end, which has been a matter of much debate. A recent ice core from Greenland demonstrates climate cooling from 122,000 years ago driven by orbitally controlled insolation, with glacial inception at 118,000 years ago. Here we present an annually resolved, layer-counted record of varve thickness, quartz grain size and pollen assemblages from a maar lake in the Eifel (Germany), which documents a late Eemian aridity pulse lasting 468 years with dust storms, aridity, bushfire and a decline of thermophilous trees at the time of glacial inception. We inte…

SOFTWARE FOR DRILLING TOOL DESIGN AND MANUFACTURING

2007

Abstract The paper presents a software that allows the design and manufacturing of cutting tools for boring. The methodology contains several steps that can be taken only by using the software modules. The main stages are the geometrical and dimensional design of the cutting tool, the design and generation of the abrasive profiled disks, the management of abrasive disks and disk package, the generation of the manufacturing technology, the verification of the cutting tool using virtual simulation, testing the manufacturing process using virtual simulation, generating the CNC files and finally the transmission of the CNC files in real time to the CNC machine tool so that the tools can be manu…

Effects of circular openings on the compressive behaviour of R.C. columns

2014

Core-drilling technique is nowadays always more frequently performed in existing reinforced concrete (RC) structures in order to investigate on the mechanical properties of concrete and for structural health monitoring purposes. Even if the engineering practice discourages to drill columns, this can be often unavoidable. In this last case the presence of the circular opening influences the compressive behavior of the column in terms of load-carrying capacity and axial deformability. The goal of this investigation was the experimental evaluation of the effects induced by circular openings on the behavior of RC columns. Twenty-four reinforced and plain concrete prisms in presence of circular …