Search results for "Dynamometer"
showing 10 items of 53 documents
Simulation with a Torque Dynamometer of Pollutants Emission from Vehicles Near Urban Cross-Road
2002
Nowadays, the influence of the vehicular traffic on the degradation of urban atmosphere is focused on by researchers belonging to different fields in view of its prime importance for public health. The control of exhaust gases emission is primary in order to keep air pollution below the specified limits of the laws in force. In previous works the “medium car” characterises a country in modelling a pollutant in urban areas. This is the central parameter of a forecasting model proposed by Pignato and LoMastro, of pollutant concentration near urban cross-road with traffic lights in continue queue and platoon flow. The proofs have been carried on two classes of displacement vehicles and four cl…
Quality evaluation of grapes for mechanical harvest using vis NIR spectroscopy
2019
Mechanical harvest of grapes is one of the operations that mostly influence the quality of the future wine. The shaking frequency of the harvesting machine is usually adjusted on the basis of the grape berry characteristics in order to limit grape juice production that is a potential cause of uncontrolled fermentations. These evaluations usually require time, personnel and laboratory analyses. The introduction of a vis NIR system to rapidly and reliably evaluate the berry properties in field before mechanical harvest could be a good alternative. The aim of this study was to evaluate the feasibility of applying vis NIR spectroscopy as a non-destructive technique on grapes cv. Syrah and Chard…
Analog isolated electronic dynamometer based on a magnetoresistive current sensor.
2017
In this work, an electronic system is presented to measure the force applied by a solenoid. The originality of the work is focused on the use of a magnetoresistive current sensor to provide the isolation barrier needed in the actual industrial plant where the solenoids are working. The design of the electronic system is presented as well as experimental measurements as a result of a calibration process showing a negligible hysteresis with that specific sensor. The magnetoresistive current sensor is used to develop transmission functions rather than playing its usual sensing roles.
Validity and reliability of the DiCI for the measurement of shoulder flexion and abduction strength in asymptomatic and symptomatic subjects
2021
Background A higher risk of shoulder injury in the athletic and non-athletic population is frequently associated with strength deficits. Therefore, shoulder strength assessment can be clinically useful to identify and to quantify the magnitude of strength deficit. Thus, the aim of this study was to evaluate the validity and reliability of a DiCI (a new hand-held dynamometer) for the measurement of shoulder flexion and abduction strength in asymptomatic and symptomatic subjects. Methods Forty-three recreational athletes (29 males and 14 females; age: 22.1 ± 0.47 years; body mass: 68.7 ± 13.1 kg; height = 173.3 ± 9.7 cm) and 40 symptomatic subjects (28 males and 12 females; age: 49.9 ± 8.1 y…
Theoretical-Applicative Research on Design and Implementation of a Special Dynamometer
2013
The topic of he present paper is taken from the Automotive Systems Nurnberg, Sibiu. It refers to the product automatic gear box which equips a few FORD models, the specific part for which the research was developed being a auto screwing bolt for plastic which raises problems at the robotized screwing because of the poor knowledge of the accurate value of the axial force and the necessary torque.
Using the modern CNC controllers capabilities for estimating the machining forces during the milling process
2017
Machining forces can nowadays be measured by using 3D dynamometers, which are usually very expensive devices and hardly available for most of the CNC machine-tools users. On the other hand, modern CNC controllers have nowadays the ability to display and save many outputs within the machining process, such as the currents or even the torques at the shaft's level for the feed motors on each axis. These outputs can be used for estimating the machining forces, but it is to be noticed that the above-mentioned currents and torques are proportional with the overall resistant forces, which includes not only technological forces, but also friction, inertial and pre-tensioning forces. This paper pres…
Motor unit discharge rate in dynamic movements of the aging soleus
2014
Aging is related to changes at the muscular level, leading to a decline in motor performance increasing the risk of falling and injury. It seems that the age-related changes in motor unit activation are muscle- and intensity dependent. The purpose of this study was to examine possible differences in soleus motor unit discharge rate (MUDR) in both isometric and dynamic contractions between young and elderly adults. 11 young (YOUNG) and 8 elderly (OLD) males participated in the study. The subjects performed isometric and dynamic plantar flexions while seated in an ankle dynamometer. The force levels studied were 10, 20, 40, 60, 80 and 100% of the isometric (ISO) MVC in ISO and 10, 20 and 40% …
Cardiorespiratory and Neuromuscular Responses to Motocross Riding
2008
The aim of the present study was to examine physiological and neuromuscular responses during motocross riding at individual maximal speed together with the riding-induced changes in maximal isometric force production. Seven A-level (group A) and 5 hobby-class (group H) motocross-riders performed a 30-minute riding test on a motocross track and maximal muscle strength and oxygen uptake (VO2max) tests in a laboratory. During the riding the mean (+/-SD) VO2 reduced in group A from 86 +/- 10% to 69 +/- 6% of the maximum (P < 0.001), whereas in group H the corresponding reduction was from 94 +/- 25% to 82 +/- 20% (P < 0.05). This relative VO2 during the riding correlated with riding speed (r = 0…
Inter- and intrarater reliability of two proprioception tests using clinical applicable measurement tools in subjects with and without knee osteoarth…
2017
Abstract Background The therapeutic value of proprioceptive-based exercises in knee osteoarthritis (KOA) management warrants investigation of proprioceptive testing methods easily accessible in clinical practice. Objective To estimate inter- and intrarater reliability of the knee joint position sense (KJPS) test and knee force sense (KFS) test in subjects with and without KOA. Design Cross-sectional test-retest design. Method Two blinded raters performed independently repeated measures of the KJPS and KFS test, using an analogue inclinometer and handheld dynamometer, respectively, in eight KOA patients (12 symptomatic knees) and 26 healthy controls (52 asymptomatic knees). Intraclass correl…
An exploration of the differences in hip strength, gluteus medius activity, and trunk, pelvis, and lower-limb biomechanics during different functiona…
2020
ABSTRACT The purpose of the study was to explore differences in the coronal biomechanics of the trunk, pelvis, hip, and knee joints, and gluteus medius muscle activity (GMed) during walking and step down from two riser heights. Joint kinematics and kinetics from 20 healthy participants were recorded using a 10-camera Qualisys system and force plates, and GMed EMG was recorded using a Delsys Trigno system. Hip abductor strength was measured using a hand-held dynamometer. Pelvic obliquity and lateral trunk bending excursions were significantly higher in walking than in step-down tasks. Significantly greater knee adduction moments were seen during both step-down tasks compared to level walking…