Search results for "ELECTRICITY"
showing 10 items of 1225 documents
A new phase in ferroelectric oxides: The phase of charge transfer vibronic excitons
2001
It is shown, by means of Hartree-Fock-type calculations using the intermediate neglect of the differential overlap (INDO) method, that polaronic-type charge transfer vibronic excitons (CTVE) in ferroelectric oxides could lead to the formation of a new phase. The ground-state energy of this phase of strongly correlated CTVE lies within an optical gap of pure crystal, and is characterized by a strong tetragonal lattice distortion, as well as ferroelectric and antiferromagnetic ordering. It is shown also that clusters of the CTVE phase being stabilized by oxygen vacancies could be responsible for the unusually strong optical Second Harmonic Generation (SHG) in nominally pure incipient ferroele…
Elektroutlenianie odpadowego syntetycznego oleju silnikowego w wodnym roztworze H2SO4
2017
W pracy przedstawiono badania nad możliwością wykorzystania odpadowego syntetycznego oleju silnikowego do bezpośredniego wytwarzania energii elektrycznej. Pomiary przeprowadzono w zakresie temperatur 293–333 K. Obejmowały one elektroutlenianie emulsji odpadowego (zużytego) syntetycznego oleju silnikowego na elektrodzie platynowej w wodnym roztworze H2SO4. Do wytworzenia emulsji wykorzystano niejonowy środek powierzchniowo czynny Syntanol DS-10. Maksymalna uzyskana gęstość prądu wyniosła 22 mA/cm2 (dla temp. 333 K). Wykazano więc, że istnieje możliwość bezpośredniego wytwarzania prądu elektrycznego z odpadowego syntetycznego oleju silnikowego, a więc zasilania nim ogniw paliwowych.
Ogniwo paliwowe zasilane emulsją oleju rzepakowego
2017
W pracy przedstawiono badania nad możliwością wykorzystania oleju rzepakowego jako substancji czynnej do zasilania ogniwa paliwowego. W tym celu zbudowano testowe ogniwo paliwowe. Ogniwo zasilano emulsją oleju rzepakowego. Jako detergent zastosowano Syntanol DS-10. Wykorzystano anodę z katalizatorem platynowym oraz katodę z katalizatorem Ni-Co. Pomiary przeprowadzono w temperaturze 293–333K. Maksymalna uzyskana gęstość prądu wynosiła 2 mA/cm2, natomiast maksymalna moc ogniwa 21 mW (dla temp. 333K). Wykazano, więc możliwość bezpośredniego dostarczania oleju rzepakowego (w formie emulsji) na anodę. Uzyskana moc ogniwa była stosunkowo niska, jednak istnieje możliwość zbudowania ogniwa paliwowe…
A New Solution for Sea Wave Energy Harvesting, the Proposal of an Ironless Linear Generator
2020
The paper investigates an innovative ironless linear generator, installable inside a wave energy converter, in order to produce electricity from sea waves. This energy source is considered strategic for the future, especially in small islands
Thermoelectrics: From history, a window to the future
2019
Thermoelectricity offers a sustainable path to recover and convert waste heat into readily available electric energy, and has been studied for more than two centuries. From the controversy between Galvani and Volta on the Animal Electricity, dating back to the end of the XVIII century and anticipating Seebeck’s observations, the understanding of the physical mechanisms evolved along with the development of the technology. In the XIX century Ørsted clarified some of the earliest observations of the thermoelectric phenomenon and proposed the first thermoelectric pile, while it was only after the studies on thermodynamics by Thomson, and Rayleigh’s suggestion to exploit the Seebeck effect for …
Generalization Capacity Analysis of Non- Intrusive Load Monitoring using Deep Learning
2020
Appliance Load Monitoring is a technique used to monitor devices existing in homes, industry or naval vessels. Acquisition of device-level data can provide great benefits in many areas such as energy management, demand response, and load forecasting. However, the monitoring process is often provided with a costly installation, as it requires a large number of sensors and a data center. Non-Intrusive Load Monitoring (NILM) is an alternative and cost-efficient load monitoring solution. Simply put, NILM is the process of obtaining device-level data by analyzing the aggregated data read from the main meter that measures the electricity consumption of the whole house. Before NILM analysis is per…
Feasibility of Waste Engine Oil Electrooxidation with Ni-Co and Cu-B Catalysts
2022
To implement a circular economy policy, methods of using waste products as a starting point for other technologies are constantly researched. One of the waste products that should be disposed of after use is waste engine oil (WEO). Despite the permanent introduction of the electrification of cars, the number of combustion vehicles (and, thus, the production of WEO) is constantly increasing. For these reasons, the reuse of WEOs is extremely important; e.g., to use these oils for energy purposes. One of the potential uses of this type of oil is as fuel for fuel cells (for direct electricity production). To lower the production costs of electrodes for fuel cells, catalysts that do not contain …
Preparation and Analysis of Ni–Co Catalyst Use for Electricity Production and COD Reduction in Microbial Fuel Cells
2019
Microbial fuel cells (MFCs) are devices than can contribute to the development of new technologies using renewable energy sources or waste products for energy production. Moreover, MFCs can realize wastewater pre-treatment, e.g., reduction of the chemical oxygen demand (COD). This research covered preparation and analysis of a catalyst and measurements of changes in the concentration of COD in the MFC with a Ni&ndash
High temperature ferro-paraelectric phase transition in tris(trimethylammonium) nonachlorodiantimonate(III) (TMACA) studied by X-ray diffraction meth…
2000
Abstract The structure of [NH(CH3)3]3Sb2Cl9, tris(trimethylammonium) nonachlorodiantimonate(III) (TMACA) has been determined at 295 K and 373 K, below and above the high temperature ferro-paraelectric phase transition. In both phases the anionic sublattice of TMACA is built of characteristic two-dimensional (Sb2Cl93−)n polyanionic layers lying in the bc plane. In room temperature, ferroelectric phase (monoclinic, Pc space group) there are three crystallographically non-equivalent trimethylammonium [NH(CH3)3]+ cations. Two of them are located between polyanionic layers and the third one, disordered, inside the cavity formed by six SbCl63− octahedra. In the high temperature paraelectric phase…
Direct Electricity Production from Linseed Oil
2019
Today’s energy industry is currently facing an increasing demand for electricity. Besides to the use of coal, oil and gas, in recent years renewable energy sources have also are used. One of devices using renewable energy sources is fuel cell (FC). The most commonly used fuel for fuel cells is hydrogen. But, problems with storage of this fuel causes, that the finding new fuels for FCs are very desirable. One of these fuels can be linseed oil. Powering high efficiency power sources (like FCs) with renewable fuels (like linseed oil) will allow development of renewable energy sources and elimination or reduce of toxic substances emissions. The paper presents the research of linseed oil electro…