Search results for "Elastic"
showing 10 items of 2162 documents
Influence of Hair Density and Hair Length on Interparticle Interactions of Spherical Polymer Brushes in a Homopolymer Matrix
2003
The dynamics of hairy spherical nanoparticles in a melt of linear polymer chains has been investigated by mechanical spectroscopy as a function of particle topology and concentration. Using a simple free volume approach for the data analysis of the structural relaxation time vs concentration and the well-known hard-sphere result as a reference, a semiquantitative measure for the interparticle interactions, that is particle deformability/softness, and the effective particle size compared to the size of a nonswollen spherical brush has been determined. For these studies, model particles of hairy nanoparticles differing in either hair length or grafting density have been prepared. In contrast …
Ferroelectric LC-elastomers
1997
Ferroelectric liquid crystalline elastomers combine the rubber elasticity of polymer networks with liquid crystalline phases and ferroelectric ordering. Ferroelectric switching leads therefore to a deformation of the polymer network and an elastic stress. The coupling between both effccts can be varied by changing the topology of the netpoints.
Nanoscale mechanical characterization of polymers by AFM nanoindentations: Critical approach to the elastic characterization
2006
AFM nanoindentations show a dependence of penetration, i.e., the relative motion between the sample and the tip (indenter), on material elastic properties when using the same load. This elationship becomes visible by using of samples being homogeneous down to the scale of nanoindentation. They were prepared from materials covering a broad range of mechanical behavior: from rubbery networks to glassy and semicrystalline polymers. The elastic modulus can be obtained applying Sneddon’s elastic contact mechanics approach. To do this, some calibrations and instrumental features have to be measured accurately. All the polymers tested show that the contact between the tip and the sample is dominat…
Rheological properties of progesterone microemulsions: Influence of xanthan and chitosan biopolymer concentration
2008
In this preformulations study, rheological properties of microemulsions with progesterone (1%) were studied to analyze the effect of xanthan and chitosan at different concentrations (0.5–3%). Steady shear and oscillatory rheological properties were analyzed using a controlled stress rheometer. Steady shear data were satisfactorily adjusted to the Carreau model. For all preparations, shear-thinning behavior was observed. Zero shear viscosity (η0) increased with the biopolymer concentration. The results from dynamic experiments showed the behavior of all preparations with xanthan gum and those of chitosan to be characteristic of weak gels and liquid-like solutions, respectively. The correlati…
Morphology, rheology, and mechanical properties of a new nanobiocomposite
2015
Nanobiocomposites are a new class of biodegradable polymer materials with an ultrafine phase dispersion of the order of a few nanometers in a biodegradable polymer matrix that shows very interesting properties often very different from those of conventional filled polymers. In this work the morphology and the rheological and mechanical properties of a new nanobiocomposite made of a biodegradable copolyester based blend with an organomodified montmorillonite have been investigated to evaluate its possible use in several applications. SAXS diffractograms and TEM micrographs show that the in both the adopted processing conditions an hybrid intercalated/exfoliated morphology is observed. Rheolo…
Master curves of viscoelastic behavior in the plastic region of a solid polymer
1977
Stress relaxation and creep tests following strain ramps were made on Mylar, both above and below the yield stress. The ramp velocity was varied over a 40-fold range. All data exhibit nonlinear viscoelastic behavior. However, those obtained above the yield point, i.e., in the plastic region, could be reduced to single master curves for both the creep and the relaxation tests by means of a simple time shift factor. This factor is inversely proportional to the strain rate existing just prior to the test.
Effects of filler type and mixing method on the physical properties of a reinforced semirigid liquid crystal polymer
1996
Semirigid liquid crystalline polymers (LCPs) show some advantages with respect to rigid LCP: in particular lower processing temperatures, better compatibility with flexible thermoplastics, but also some disadvantages. Thermal resistance of rigid LCPs is much better and the maximum working temperature is, in general, very high. The thermomechanical properties can be improved by adding inorganic fillers. In this work processing, mechanical and thermomechanical properties of a filled semirigid liquid crystal copolyester are reported. Several inorganic fillers have been used in order to put in evidence the influence of shape and dimensions of the particles on the properties of the filled materi…
Processing and characterization of blends of fluoroelastomers with semirigid liquid crystal polymers
1996
Fluoroelastomers (FEs) usually have working temperatures above 150°C and a great resistance to aggressive agents such as oils, fuels, aliphatic and aromatic solvents, steam, moderate acid, and basic environments. Liquid crystal polymers (LCPs) can be effective processing aids and reinforcing agents for elastomers. These characteristics are very attractive to lower melt viscosity and to stiffen and strengthen the final product through a simple blending. Among the LCPs, the semirigid LCPs seem the most appealing for blending with flexible thermoplastics (FTs) because their processing temperatures can be arranged to be in the same processing temperature range of FTs and because the presence of…
Kenaf-filled biodegradable composites: rheological and mechanical behaviour
2012
Biodegradable polymer composites, typically based on biodegradable polymer matrices and natural-organic fillers, are gaining rising interest and importance over the last few years. Several natural-organic fillers can be used but the most widespread so far is wood, in the form of fibres or flour. Alternative cellulosic fillers can ensure advantages in terms of resource utilization and properties of the final composite. In this work, Mater-Bi® based biodegradable composites were prepared with two kinds of wood flour, and directly compared with alternative composites containing kenaf fibres. The use of kenaf fibres allowed improved elastic modulus, tensile strength and interaction with the pol…
Fractional viscoelastic characterization of laminated glass beams under time-varying loading
2021
Abstract Laminated glass is a composite made of elastic glass layers sandwiching thin viscoelastic polymeric interlayers. There are several types of polymers, traditionally modelled as linear viscoelastic materials using a Prony’s series of units in the Maxwell-Wiechert arrangement. We show that one single element with fractional viscoelastic properties (two constitutive parameters that depend on environmental temperature), is sufficient to provide an accurate description of the polymer response under arbitrary time-varying actions. This is a great advantage over the classical viscoelastic characterization, which requires at least 10–15 terms in the Prony’s series, each one characterized by…