Search results for "Elastic"
showing 10 items of 2162 documents
Elastic Modulus and Thermal Conductivity of Thiolene/TiO2 Nanocomposites
2017
Metal oxide based polymer nanocomposites find diverse applications as functional materials, and in particular thiol-ene/TiO2 nanocomposites are promising candidates for dental restorative materials. The important mechanical and thermal properties of the nanocomposites, however, are still not well understood. In this study, the elastic modulus and thermal conductivity of thiol-ene/TiO2 nanocomposite thin films with varying weight fractions of TiO2 nanoparticles are investigated by using Brillouin light scattering spectroscopy and 3ω measurements, respectively. As the TiO2 weight fraction increases from 0 to 90%, the effective elastic longitudinal modulus of the films increases from 6.2 to 37…
Morphology and Properties of Polyethylene/Clay Nanocomposite Drawn Fibers
2008
The influence of an elongational flow on the morphology of PE/clay nanocomposite drawn fibers was studied. An increase of the elastic modulus and the tensile strength as well as a decrease of the elongation at break are observed with increasing draw ratio. The applied elongational gradient orients the polymer chains and the clay particles along the spinning direction. When the applied flow results in the formation and the orientation of exfoliated nanoparticles, a pronounced increase of the mechanical properties is observed. The dispersed clay particles can be broken and oriented by the extensional flow, which might indicate a flow induced intercalated/exfoliated morphology transition.
Mechanical and thermomechanical properties of radiation modified poly(ethylene-octene)/Ni-Zn ferrite nanocomposites
2013
Poly(ethylene-1-octene) copolymer (POE) composites filled with nickel-zinc ferrite nanoparticles have been modified by exposure to an electron beam at doses up to 500 kGy. The influence of radiation dose and ferrite content on mechanical properties has been investigated. Thermomechanical properties – thermorelaxation stresses formed in thermal heating and thermo residual stresses resulting in the process of full setting and cooling of materials have been investigated for radiation cross-linked oriented (extended up to 100%) composite samples. Increase of concentration of ferrite particles and increase of radiation dose affects a notable increase of elastic modulus and reduces the deformabil…
Nanoindentation response analysis of Cu-rich carbon–copper composite films deposited by PVD technique
2015
Abstract The micromechanical properties of sputter deposited amorphous carbon–copper (a-C/Cu) composite films with different carbon content (6.8–19.8 at.%) were investigated. Atomic force and electron microscopy studies confirmed that the a-C/Cu films have a two-phase microstructure of amorphous sp 2 /sp 3 -bonded carbon as a composite matrix with embedded copper nanocrystallites encapsulated in a graphene shell. Load–displacement curves obtained in nanoindentation experiments followed Meyer's law with the exponent varying slightly within the interval 2.0–2.2 depending on the penetration depth and carbon content. The reverse indentation size effect was observed which was most likely the res…
Morphological evolution of InAs/InP quantum wires through aberration-corrected scanning transmission electron microscopy
2010
Evolution of the size, shape and composition of self-assembled InAs/InP quantum wires through the Stranski–Krastanov transition has been determined by aberration-corrected Z-contrast imaging. High resolution compositional maps of the wires in the initial, intermediate and final formation stages are presented. (001) is the main facet at their very initial stage of formation, which is gradually reduced in favour of {114} or {118}, ending with the formation of mature quantum wires with {114} facets. Significant changes in wire dimensions are measured when varying slightly the amount of InAs deposited. These results are used as input parameters to build three-dimensional models that allow calcu…
Acoustic modes in metallic nanoparticles: atomistic versus elasticity modeling
2009
The validity of the linear elasticity theory is examined at the nanometer scale by investigating the vibrational properties of silver and gold nanoparticles whose diameters range from about 1.5 to 4 nm. Comparing the vibration modes calculated by elasticity theory and atomistic simulation based on the Embedded Atom Method, we first show that the anisotropy of the stiffness tensor in elastic calculation is essential to ensure a good agreement between elastic and atomistic models. Second, we illustrate the reduction of the number of vibration modes due to the diminution of the number of atoms when reducing the nanoparticles size. Finally, we exhibit a breakdown of the frequency-spectra scalin…
Mechanical properties of the nanometer scale pre-crystalline order of a poly (ethylene terepthalate) / poly (ethylene naphthalene) blend
2006
A previous study carried out on PET has shown that this polymer undergoes a continuous structural modification over a wide cooling rate interval when solidified from the melt[1] assuming a semi-crystalline structure below 2 K s 1 and a completely amorphous one above 100 K s 1. Most important was the existence of a state of intermediate order between the above cooling rates which was evidenced by the absence of crystalline reflections in the WAXS patterns and the occurrence of SAXS maxima[2] and exothermic peak areas (DSC) in the cooling rate range above 2 K s 1. Microhardness (MH) measurements revealed that this phase affects the mechanical properties[3] plausible if one thinks of crystalli…
Bending test for capturing the vivid behavior of giant reeds, returned through a proper fractional visco-elastic model
2015
Abstract This paper presents results of experimental investigations made to evaluate the vivid behavior of giant reed Arundo donax. In particular, attention was paid to the relationship between visco-elastic properties and moisture content, which is widely recognized as one of the key factor that influences the mechanical properties of all wood-based materials. To this aim, after a controlled drying treatment on samples of reed, stress relaxation tests in three point bending configuration were performed to evaluate the effects of moisture content on visco-elastic behavior of the giant reed. Further, the novel aspect of this paper is that of using an Euler–Bernoulli model embedded with an ad…
Corrosion Protection of Steel with Oxide Nanolaminates Grown by Atomic Layer Deposition
2011
Atomic layer deposited (ALD) aluminum and tantalum oxide (Al 2 O 3 and Ta 2 O 5 ) and their nanolaminates were applied as corrosion protection coatings on AISI 52100 steel. The aim was to combine the good sealing properties of Al 2 O 3 with the chemical stability of Ta 2 O 5 and to optimize the coating architecture in order to obtain the best possible long-term durability. Coating composition and morphology were studied with time-of-flight elastic recoil detection analysis (ToF-ERDA), time-of-flight secondary ion mass spectrometry (ToF-SIMS) and field emission scanning electron microscopy (FESEM) and energy dispersive x-ray spectrometry (EDS). Electrochemical properties were studied with vo…
X-ray micro-tomography based FEM modelling of hygroexpansion in PLA composites reinforced with birch pulp fibres
2017
This article presents a microscale modelling approach coupled with X-ray computed micro-tomography for the evaluation of material properties of polylactic acid (PLA) reinforced by birch pulp fibers under the effect of moisture. The results in terms of elastic moduli and hygroexpansion deformation were found in good agreement with the measurements taken at different levels of water uptake.