Search results for "Elasticity"

Automated photoelasticity in white light: Influence of quarter-wave plates

1995

This paper deals with the influence of optical retarders on the isochromatic fringes obtained by automated white light photoelasticity using methods such as those based on spectral content analysis (SCA) and on primary colour (red, green and blue) analysis. In the following the light intensity equations of dark- and light-field polariscopes with both crossed and parallel optical retarders are reviewed. In particular, it is shown that the retardance error of the quarter-wave plates produces an attenuation of the maximum intensity in dark field and an increase of minimum intensity in light field. Experimental evidence of the influence of optical retarders is also shown.

Holographic photoelasticity: Influences of inaccuracies of optical retarders on isochromatics and isopachics

1974

In this paper the influence of inaccuracies of the optical retarders on the isochromatic and isopachic fringes obtained by holographic photoelasticity is studied. For the single-exposure hologram it is shown that the isochromatic visibility decreases as for light- and dark-field configurations, whereas the isochromatic fringes are distorted only for the dark-field configuration. For the double-exposure hologram it is shown that the isopachic fringes are generally distorted; with the isochromatics there is a decrease of fringe visibility. Experimental results confirming the theory are reported.

Photoelastic Analysis of Edge Residual Stresses in Glass by the Automated Tint Plate Method

2013

The analysis of residual stress in glass is usually carried out by means of photoelastic methods. This article considers the automation of the white light photoelastic method based on the use of a full-wave plate placed behind the glass plate. In particular, the method in based on the use of RGB photoelasticity in white light in conjunction with a full wave plate. The proposed method have been applied to the analysis of membrane residual stresses in tempered glass, showing that it can effectively replace manual methods of photoelastic analysis of residual stresses in glass when a low photoelastic retardation is present.

Limitation of fourier transform photoelasticity: Influence of isoclinics

2000

The application of the Fourier transform to photoelasticity was used in the evaluation of the retardation using a carrier system of fringes. In photoelasticity, the light intensity from the analyzer in a circular polariscope depends on both the retardation (isochromatics) and the isoclinic parameter. The theoretical analysis shows that the angle between the principal stresses in the model and in the carrier system of fringes influences the evaluation of the retardation (isochromatics), as occurs when misaligned compensators (namely, Babinet) are used. As a consequence, this method may not be applied as a full-field technique, although the error is small if the angle between the principal st…

A review of automated methods for the collection and analysis of photoelastic data

1998

Photoelasticity is one of the most widely used full-field methods for experimental stress analysis. However, the collection of photoelastic parameters can be a long and tedious process. The advent of automated photoelastic systems has allowed the experimentalists to speed up the rate of analysis and to perform more complex investigations. This paper provides a survey of recent methods of automated photoelasticity developed in the last 20 years, i.e. methods of the fringe centres, half-fringe photoelasticity, phase-stepping photoelasticity, methods based on the Fourier transform, spectral content analysis (SCA) and RGB (red, green, blue) photoelasticity.

Automated Stress Separation Along Stress Trajectories

2007

A procedure for the separation of principal stresses in automated photoelasticity is presented. It is based on the integration of indefinite equations of equilibrium along stress trajectories, also known as Lame-Maxwell equations. A new algorithm for precise and reliable stress trajectory calculation, which is an essential feature of the procedure, has also been developed. Automated stress separation is carried out along stress trajectories starting from free boundaries. Experimental tests were performed on a disc in diametral compression and on a ring with internally applied pressure. Full-field principal stress values were obtained and results were compared with those from the theory of e…

Numerical simulations and experimental measurements of the stress intensity factor in perforated plates

2008

A numerical procedure, which combines two hybrid finite element formulations, was developed to analyse the stress intensity factors in cracked perforated plates with a periodic distribution of holes and square representative volume elements. The accuracy of the method in predicting the stress intensity factor was verified by a comparison with experimental measurements, carried out by a photoelasticity method, and by commercial finite element software. Several simulations were executed by varying both the crack length and the hole diameters, and the effects of the holes on the stress intensity factor are illustrated. The method shows high accuracy and efficiency, as small differences were ob…

Elastic force in Kant?s early works

2018

This paper argues that the notion of elastic force is an important and overlooked thread running through a number of Kant’s writings from 1754 to 1764. After presenting the historical context, I argue that the key aspects of Kant’s early understanding of physical elasticity can be found in On Fire (1755) and show how Kant attempts to explain a wide range of phenomena through elasticity. On my account, one aim of his account of physical monads is provide metaphysical grounds for elastic phenomena. Finally, I examine Kant’s hints that minds can be understood through an analogy with elastic physical phenomena. ispartof: Revista de Estudios Kantianos vol:3 issue:2 pages:190-207 status: published

Statistical Methods for Parameter Identification of Temperature Dependent Viscoelastic Models

2018

On the effect of damping on dispersion curves in plates

2013

AbstractThis paper presents a study on quantitative prediction and understanding of time-harmonic wave characteristics in damped plates. Material dissipation is modelled by using complex-valued velocities of free dilatation and shear waves in an unbounded volume. As a numerical example, solution of the classical Rayleigh–Lamb problem for a viscoelastic plate is presented to illustrate and discuss the role of dissipation in the cut-off phenomenon and in the phenomenon of veering for dispersion curves. These phenomena are explained in more detail considering a simple model, which allows accurate asymptotic analysis of the perturbation of dispersion curves in the regions of cut-off and veering.