Search results for "Electron microscope"

Local electrochemical impedance spectroscopy study of the influence of ageing in air and laser shock processing on the micro-electrochemical behaviou…

2011

International audience; In the present paper, the micro-electrochemical behaviour of AA2050-T8 in 0.1 M NaCl was first studied after polishing by means of local electrochemical impedance spectroscopy and field-emission scanning electron microscopy/electron dispersive spectroscopy (FE-SEM/EDS). The influence of ageing in air and LSP was then investigated. Ageing in air for three months led to an increase in the charge transfer resistance. This was clearly observed in sites surrounding constituent particles where the charge transfer resistance was in the order of 1 MΩ cm2 (instead of 10-3 MΩ cm2 after polishing). Increased passivity around particles was confirmed from FE-SEM/EDS analysis. On …

TEM studies on La2−2xCa1+2xMn2O7 (x=0.5 and 0.25)

2003

The nominal compositions and structures of the compounds La2-2xCa1+2xMn2O7 (x=0.5 and 0.25) prepared by solid-state reaction have been studied by transmission electron microscopy and high-resolution electron microscopy. Besides the observation of the major phase of a two-layer structure in the nominal composition La1.0Ca2.0Mn2O7, the embedded n = 3, n = 4 Ruddlesden-Popper phases and La rich phase in the two-layer structure were observed as defects. No layered structure was observed in the nominal composition La1.5Ca1.5Mn2O7. Instead, a major phase of orthorhombically distorted perovskite, a minor phase of an ideal cubic perovskite, and a small fraction of calcium-oxide were observed in the…

Cutting single-walled carbon nanotubes with an electron beam: evidence for atom migration inside nanotubes.

2006

<title>Miniaturized objective lens for a photoelectron emission microscope</title>

2000

Photoemission electron microscopy (PEEM) has turned out to be one of the most promising methods for surface analysis in the recent years. It is a full field imaging technique based on the emission of secondary electrons by far ultraviolet light or X-rays. The emission intensity of secondary electrons is critically dependent upon the acceptance angle of the incident radiation. However, the size of the microscope restricts this angle substantially. Miniaturizing the objective lens of the microscope reduces the restriction of the acceptance angle and improves the performance of the PEEM considerably. We report on the fabrication of a miniaturized objective lens containing the extraction electr…

Spray pyrolytic deposition of ZnO thin layers composed of low dimensional nanostructures

2010

Abstract ZnO nanolayers composed of fine nanostructures have been successively grown by spray pyrolytic deposition at 300  ∘ C over amorphous glass substrates. As deposited samples were analysed by scanning electron microscopy (SEM), showing a granular morphology with grain size in the limit of the microscope resolution. CL measurement shows a broad near band edge (3.4 eV) emission of ZnO in the UV region and the defect level emissions in the green region of the spectrum. The use of intermittent spray pyrolytic deposition is shown as an alternative to increase the homogeneity of the samples when temperatures near to the precursor pyrolytic decomposition is selected, long depositions times a…

The Effect of Building Direction on Microstructure and Microhardness during Selective Laser Melting of Ti6Al4V Titanium Alloy

2021

AbstractDuring the last few years, additive manufacturing has been more and more extensively used in several industries, especially in the aerospace and medical device fields, to produce Ti6Al4V titanium alloy parts. During the Selective Laser Melting (SLM) process, the heterogeneity of finished product is strictly connected to the scan strategies and the building direction. An optimal managing of the latter parameters allows to better control and defines the final mechanical and metallurgical properties of parts. Acting on the building direction it is also possible to optimize the critical support structure. In particular, more support structures are needed for the sample at 0°, while very…

Electrogeneration of Diiodoaurate in Dimethylsulfoxide on Gold Substrate and Localized Patterning

2016

International audience; A localized etching of gold surface by scanning electrochemical microscope technique is presented where a dimethylsulfoxide-based electrolyte charged with iodine is used. The electrogenerated triiodide ion at the platinum ultramicroelectrode tip (feedback mode) acts as an oxidant for gold surface. The effects of electrode diameter and the bias time have been investigated. The approach curve method was used to hold the electrode tip close to the gold surface. A scanning electron microscope is used to observe the etched gold surfaces where disk-shaped dots are generated. The diameter of these holes depends directly on the Pt electrode diameter and the bias time.

One-Step Anionic Copolymerization Enables Formation of Linear Ultrahigh-Molecular-Weight Block Copolymer Films Featuring Vivid Structural Colors in t…

2018

Ultrahigh-molecular-weight (UHMW) tapered block copolymers (BCPs) consisting of polyisoprene-block-poly(4-methylstyrene) featuring overall molar masses in the range of 1101–2033 kg mol–1 (Mw) are synthesized via a convenient one-step anionic copolymerization protocol. The obtained UHMW BCPs are investigated by differential scanning calorimetry, size exclusion chromatography, and 1H NMR spectroscopy. Microphase separation for the UHMW BCPs in the bulk state is investigated by transmission electron microscopy (TEM) measurements and scanning electron microscopy (SEM), revealing well-ordered lamellar and spherical domains with large domain sizes in the range of 100–200 nm. Excellent order and p…

Fluoride-induced precipitates on enamel surface and subsurface areas visualised by electron microscopy and confocal laser scanning microscopy

1997

The present study examined the enamel surface after in vitro topical treatments with a neutral 2% NaF solution. For minimising the risk of artefacts, samples were inspected without pre-treatment as fresh, naturally wet specimens by complementary techniques: variable pressure electron microscopy (VP-SEM) and confocal laser scanning microscopy (CLSM). VP-SEM provided information on the surface morphology, whereas CLSM allowed non-destructive visualisation of subsurface areas. Neutral NaF solutions induced globular precipitates on the enamel surfaces. If the globules formed may be described as "calcium fluoride like material", the additional information of this experiment is that, after intera…

Tetrathiotetracene thin film morphology and electrical properties

2015

The electrical properties of organic thin films are determined by their chemical constituents and the morphology of the films deposited. In this paper the morphology of vacuum sublimed (7?10-6 mbar) tetrathiotetracene (TTT) thin films is shown to be strongly affected by the thermal deposition temperature (222-350 K) and rate of deposition. Mostly needle-like morphologies are identified by scanning electron microscopy. Optimal TTT purity (a pre-requisite for device preparation via subsequent oxidation) is evidenced by their initially low electrical conductivity. Altering the TTT morphology, by variation of the evaporation parameters, strongly affects this base electrical conductivity. Four p…