Search results for "Energy Engineering"
showing 10 items of 1099 documents
Wireless battery charging for electric bicycles
2017
The contactless solution is increasingly spreading as method of battery charging for Electric Vehicles (EVs). The standard technology of contactless EV battery charging is based on the Inductive Power Transfer (IPT) between two coupled coils, one connected to the electrical grid and the other one connected to the rechargeable battery. The IPT provides benefits in terms of safety and comfort, due to the absence of a plug-in operation. In this paper, an overview on the IPT applied to the battery charging of electric bicycles is provided, with some general considerations on the technical implications. Moreover, a prototype of contactless battery charging for E-bikes is proposed and described.
Electrical power production from low-grade waste heat using a thermally regenerative ethylenediamine battery
2017
Abstract Thermally regenerative ammonia-based batteries (TRABs) have been developed to harvest low-grade waste heat as electricity. To improve the power production and anodic coulombic efficiency, the use of ethylenediamine as an alternative ligand to ammonia was explored here. The power density of the ethylenediamine-based battery (TRENB) was 85 ± 3 W m−2-electrode area with 2 M ethylenediamine, and 119 ± 4 W m−2 with 3 M ethylenediamine. This power density was 68% higher than that of TRAB. The energy density was 478 Wh m−3-anolyte, which was ∼50% higher than that produced by TRAB. The anodic coulombic efficiency of the TRENB was 77 ± 2%, which was more than twice that obtained using ammon…
High-performing Sn-Co nanowire electrodes as anodes for lithium-ion batteries
2012
Abstract The preparation of Sn 2 Co 3 nanowire arrays (NWs) electrogrown inside the channels of polycarbonate membranes and their characterization as anodes for Li-ion batteries both in half-cell vs. Li and in battery configuration are reported. The Sn 2 Co 3 NW electrodes tested by deep galvanostatic charge/discharge cycles in ethylene carbonate-dimethylcarbonate (1:1) – LiPF 6 1 M displayed 80% capacity retention after 200 cycles at C/2 and 30 °C, and a high charge and discharge rate capability at C-rate from C/3 (0.33 A/g) to 10C (10 A/g) at 30° and 10 °C. Electrodes with the highest alloy loading delivered up to 0.6 mAh cm −2 at C/2. The performance of these electrodes in battery config…
Improved composite materials for rechargeable lithium metal polymer batteries
1999
Abstract The performance of several polymer electrolytes for lithium metal batteries for electric vehicle applications are reported. The best performing electrolyte is the composite PEO 20 LiCF 3 SO 3 –γLiAlO 2 , which was prepared by a solvent-free procedure. It showed coulombic efficiency values of the lithium deposition–stripping process of 94%–96%. Electrochemical tests of lithium polymer battery (LPB) prototypes based on a 3 V LiMn 2 O 4 composite cathode material laminated together with the PEO 20 LiCF 3 SO 3 –γLiAlO 2 electrolyte gave promising results for electric vehicle applications. Even under non-optimized battery design, the prototypes delivered, at the C/3 rate and at 94°C, 40…
Experimental Investigation on Magnetic Field Effects of IPT for Electric Bikes
2018
The wireless power transmission (WPT) is increasingly representing a promising technology and an innovative solution, especially for the electric vehicles (EVs) battery charging. The inductive power transfer (IPT) is the standard technology of wireless charging: the energy transfer occurs between two magnetically coupled coils. The IPT-based battery charging is especially convenient for E-bikes and the physiological effects related to the generated magnetic fields should be estimated. In this context, this work presents a 200Â W prototype of wireless battery charger for E-bikes. In addition, the measurements regarding the surrounding magnetic field are given in detail in order to evaluate t…
An efficient wireless power transfer prototype for electrical vehicles
2017
Based on the inductive power transfer (IPT), the contactless approach allows safe and comfortable operations of battery charging for Electric Vehicles (EVs). In this paper, a contactless system particularly suitable for E-bike battery charging is proposed. A practical realization of the system has been carried out, aiming at the system evaluation in terms of working and efficiency. Through a phase shift modulation, a power regulation has been implemented. The target power level is 100 W.
Wireless Power Transmission for house appliances: A small-scale resonant coupling prototype
2016
This paper presents a low cost prototype of wireless power transfer system based on resonant coupling. The system here proposed can be useful for house appliances battery charging systems: as a matter of fact, it consists mainly of two copper wire coils or windings, placed one in front of the other on the same axis. By exploiting the coils resonance coupling effect, electric energy can be transferred from the inductor coil to the receiver in order to charge the batteries. Low cost experimental tests demonstrated the effectiveness of the proposed wireless power transfer prototype, being it capable to reach an efficiency of about 80% and more along a distance of 30 cm.
Optimization of urban delivery systems based on electric assisted cargo bikes with modular battery size, taking into account the service requirements…
2021
The implementation of new forms of urban mobility is a fundamental challenge for improving the performance of city logistic systems in terms of efficiency and sustainability. For such purposes, the exploitation of electric vehicles is currently being investigated as an alternative to traditional internal combustion engines. In particular, the employment of lightweight electric cargo bikes is seen as an attractive possibility for designing improved city distribution systems. Such vehicles, however, present substantial limitations related to their endurance, speed, power, and recharging times; therefore, their configuration must be optimized considering the actual operational context and the …
Modeling and Performance Assessment of the Split-Pi Used as a Storage Converter in All the Possible DC Microgrid Scenarios. Part II: Simulation and E…
2021
Bidirectional DC/DC converters such as the Split-pi can be used to integrate an energy storage system (ESS) into a DC microgrid providing manifold benefits. However, this integration deserves careful design because the ESS converter must behave like a stiff voltage generator, a non-stiff voltage generator, or a current generator depending on the microgrid configuration. Part I of this work presented a comprehensive theoretical analysis of the Split-pi used as an ESS converter in all the possible DC microgrid scenarios. Five typical microgrid scenarios were identified. Each of them required a specific state-space model of the Split-pi and a suitable control scheme. The present paper complete…
A comparison of HDFS compact data formats: Avro versus Parquet
2017
In this paper, file formats like Avro and Parquet are compared with text formats to evaluate the performance of the data queries. Different data query patterns have been evaluated. Cloudera’s open-source Apache Hadoop distribution CDH 5.4 has been chosen for the experiments presented in this article. The results show that compact data formats (Avro and Parquet) take up less storage space when compared with plain text data formats because of binary data format and compression advantage. Furthermore, data queries from the column based data format Parquet are faster when compared with text data formats and Avro. Article in English. HDFS glaustųjų duomenų formatų palyginimas: Avro prieš Parquet…