Search results for "Engineering sciences"
showing 10 items of 2347 documents
In-flight temperature of solid micrometric powders during cold spray additive manufacturing
2020
Abstract During cold dynamic gas spray additive manufacturing, the thermal field within particles is generally simplified by a state of an instantaneous uniform distribution over the particle's media at any position inside and outside the De-Laval nozzle. This paper addresses critical discussions using analytical and computational analysis of the transient heat transfer within the solid particles due to the convective exchange with the flowing gas. An analytical criterion depicts conditions of instantaneous uniform temperature over the range of typical cold spray data including various particle thermal conductivity, particle size range, dragging velocities, gas nature and gas setting condit…
Sintering of copper nanopowders under hydrogen: an in situ X-ray diffraction analysis.
2003
Abstract The reduction by hydrogen gas of the cuprite layer on copper nanocrystals and the subsequent sintering of the nano-particles were studied using in-situ X-ray diffraction and dilatometry. Spherical nanocrystals produced by evaporation and condensation have an average size of 35 nm, exhibiting a large surface curvature. Each nanoparticle is coated with a 3.5 nm layer of Cu 2 O, which is rough and disordered, as revealed by high-resolution electron microscopy. Reduction by hydrogen of this curved cuprite layer occurs at 363 K, which is ≈65 K lower than is observed on a layer supported by micrometer-sized or bulk copper with a flat surface. The reduction process and its effect on the s…
Effect of current on the sintering of pre-oxidized copper powders by SPS
2017
Abstract As mentioned in the literature, SPS (Spark Plasma Sintering) technology combines uniaxial charge and pulsed currents to achieve the rapid sintering of powders. Although the utilization of current is often reported, an understanding of its role in the sintering mechanisms is still a subject of controversy. In fact, the oxide layer around metal particles is sometimes considered to be a dielectric gap in which discharges may occur: these discharges can clean the surface of particles and enhance densification. In this paper, an oxide layer was grown on the particle surface of a copper powder, and the growth enabled the study of the role of current on such dielectric layers. The powders…
Grafting and characterization of dodecylphosphonic acid on copper: Macro-tribological behavior and surface properties
2013
International audience; Thin film of n-dodecylphosphonic acid (DDPA) was prepared on a copper oxide substrate via a molecular self-assembly process. The composition, structure, organization, surface energy, morphology, and electrochemical behavior of the DDPA filmwere characterized bymeans of X-ray photoelectron spectroscopic analysis (XPS), polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS), contact angle measurement v(CAM), microscopic observations, and electrochemistry. The friction behavior of the DDPA film adsorbed on copper oxide substrate sliding against a Si3N4 ball was examined on a linear reciprocating tribological tester. Worn surfaces of the DDPA film…
Model predictive control for continuous lactide ring‐opening polymerization processes
2020
International audience; Polylactic acid (PLA) is an attractive environment-friendly thermoplastic that is bio-sourced and biodegradable. PLA is industrially produced by the ring-opening polymerization of Lactide. This reaction is sensitive to drifts in the operating conditions and impurities in the raw materials that may affect the reaction rate as well as the polymer properties, which can be very costly in continuous processes. It is therefore crucial to employ a control strategy that allows recovering the nominal conditions and maintaining the desired properties and conversion level in case of drift. Three control strategies are discussed in this paper: Proportional-Integral controller (P…
High-order modes in cavity-resonator-integrated guided-mode resonance filters (CRIGFs)
2015
International audience; Cavity-resonator-integrated guided-mode resonance filters (CRIGFs) are optical filters based on weak coupling by a grating between a free-space propagating optical mode and a guided mode, like guided-mode resonance filters (GMRFs). As compared to GMRFs they offer narrowband reflection with small aperture and high angular acceptance. We report experimental characterization and theoretical modeling of unexpected high-order reflected modes in such devices. Using coupled-mode modeling and moiré analysis we provide physical insight on key mechanisms ruling CRIGF properties. This model could serve as a simple and efficient framework to design new reflectors with tailored s…
Acousto-optic cavity coupling in 2D phoxonic crystal with combined convex and concave holes
2021
International audience; A two-dimensional cross-like phoxonic crystal (PxC) model is proposed, which exhibits simultaneously large complete photonic crystal (PtC) and phononic crystal (PnC) bandgaps. The most salient trait of the structure is the wide range of geometrical parameters compatible with large complete bandgaps. After geometrical optimization, photonic and phononic bandgaps with gap-to-midgap ratios of 11.5% and 90.7% are obtained, respectively. These values are close to the best topology-optimized reported values but are obtained with simple shapes compatible with nanoscale fabrication technology. These characteristics make the convex–concave topology a promising candidate for P…
Attitude estimation from polarimetric cameras
2018
International audience; In the robotic field, navigation and path planning applications benefit from a wide range of visual systems (e.g. perspective cameras, depth cameras, catadioptric cameras, etc.). In outdoor conditions, these systems capture information in which sky regions cover a major segment of the images acquired. However, sky regions are discarded and are not considered as visual cue in vision applications. In this paper, we propose to estimate attitude of Unmanned Aerial Vehicle (UAV) from sky information using a polarimetric camera. Theoretically , we provide a framework estimating the attitude from the skylight polarized patterns. We showcase this formulation on both simulate…
Echo cancellation system for iso-frequency repeaters : contribution to the development of a new generation digital repeater
2014
On-frequency repeaters are a cost-effective solution to extend coverage and enhance wireless communications, especially in shadow areas. However, coupling between the receiving antenna and the transmitting antenna, called radio frequency echo, increases modulation errors and creates oscillations in the system when the echo power is high. According to the communication standards, extremely weak echoes decrease the transmission rate, while strong echoes damage electroni ccircuits because of power peaks. This thesis aims at characterizing the echo phenomenon under different modulations, and proposing an optimized solution directly integrated to industry. We have turned to digital solutions esp…
Analyse expérimentale et numérique du comportement de véhicules terrestres en présence d'un vent latéral instationnaire
2013
The automotive manufacturers are nowadays more and more interested in crosswind aerodynamics. Indeed, the driver is subjected every day to strong side air flows, for example when overtaking another vehicle or when passing through a lateral wind wall, generated by terrain topography (as in the case of the passage near the empty space between two buildings).The aerodynamic efforts generated in these situations can lead to undesired lateral deviations,which can be dramatic if the driver is surprised. Different experimental studies, reproducing the effects of a dynamic yaw angle, pointed out the issues of the steady methods, commonly used to qualify the vehicle crosswind behaviour. Little is st…