Search results for "Engineering sciences"
showing 10 items of 2347 documents
Multifunctional derivatives of dimethoxy-substituted triphenylamine containing different acceptor moieties
2020
This project has received funding from the Research Council of Lithuania (LMTLT), Agreement No. [S-LZ-19-2]. This research was funded by the Région Centre, the Tunisian ministry of research, University of Monastir and the French ministry of Higher Education and Research. J. Bouclé would like to thank the Sigma-Lim LabEx environment for financial supports, and the PLATINOM facility at XLIM laboratory regarding device fabrication and characterizations. DG acknowledges the Lithuanian Academy of Sciences for the financial support.
Structural analysis of W3O/WO3 and TiO/TiO2 periodic multilayer thin films sputter deposited by the reactive gas pulsing process
2012
International audience; DC reactive sputtering was used to deposit titanium and tungsten-based metal/oxide periodic nanometric multilayers using pure metallic targets and Ar + O-2 gas mixture as reactive atmosphere. The innovative technique namely, the reactive gas pulsing process allows switching between the metal and oxide to prepare a periodic multilayered structure with various metalloid concentrations and nanometric dimensions. The same pulsing period was used for each deposition to produce metal-oxide periodic alternations close to 10 nm. Structure, crystallinity and chemical composition of these films were systematically investigated by Raman spectroscopy, X-ray diffraction and Energ…
A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites
2012
Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…
Influence of the microstructure and laser shock processing (LSP) on the corrosion behaviour of the AA2050-T8 aluminium alloy
2011
International audience; The corrosion behaviour of AA2050-T8 was studied after polishing and after laser shock processing (LSP) treatment using the electrochemical microcell technique and the SVET. After polishing, pitting at constituent particles and intergranular corrosion were observed. By contrast, no intergranular corrosion developed after LSP. Microcell measurements revealed that LSP increases the pitting potential. SVET measurements revealed that local anodic currents are systematically lower on LSP-treated surfaces than on polished ones. The current density on the LSP-treated surface remains constant around 50 μA cm−2 up to 123 min after immersion, while on the polished surface it r…
Cooperativity Scaling and Free Volume in Plasticized Polylactide
2019
The authors would like to thank the region Haute Normandie for their financial support and the acquisition of the Broadband Dielectric Spectrometer. R.G. acknowledges U.S. National Science Foundation (Grant no. DMR-1725188) for the acquisition of PAL spectrometer. The experimental evidence of the increase of activation energy associated with the super Arrhenius behavior governing amorphous polylactide by free volume variations has been obtained through a combination of calorimetric, dielectric, and positron annihilation lifetime measurements. The amount of free volume in polylactide was controlled by the amount of acetyltributylcitrate plasticizer in the composition. Plasticization is shown…
Local electrochemical impedance spectroscopy study of the influence of ageing in air and laser shock processing on the micro-electrochemical behaviou…
2011
International audience; In the present paper, the micro-electrochemical behaviour of AA2050-T8 in 0.1 M NaCl was first studied after polishing by means of local electrochemical impedance spectroscopy and field-emission scanning electron microscopy/electron dispersive spectroscopy (FE-SEM/EDS). The influence of ageing in air and LSP was then investigated. Ageing in air for three months led to an increase in the charge transfer resistance. This was clearly observed in sites surrounding constituent particles where the charge transfer resistance was in the order of 1 MΩ cm2 (instead of 10-3 MΩ cm2 after polishing). Increased passivity around particles was confirmed from FE-SEM/EDS analysis. On …
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
Real time polarization imaging of weld pool surface
2015
The search for an efficient on-line monitoring system focused on the real-time analysis of arc welding quality is an active area of research. The topography and the superficial temperature field of the weld pool can provide important information which can be used to regulate the welding parameters for depositing consistent welds. One difficulty relies on accessing this information despite the bright dazzling welding arc. In the present work, Stokes polarimetry and associated shape-from-polarization methods are applied for the analysis of the weld pool through its 810 nm-wavelength infrared emissions. The obtained information can provide a better understanding of the process, such as the usa…
Manufacturing and testing of a metal supported Ni-YSZ/YSZ/La2NiO4 IT-SOFC synthesized by physical surface deposition processes
2017
International audience; The manufacture of the last generation metal supported IT-SOFC complete cell by dry surface deposition pro-cesses is really challenging. Atmospheric Plasma Spraying (APS) and Reactive Magnetron Sputtering (RMS) processes are respectively adapted to deposit Ni-YSZ anode and YSZ electrolyte layers. RMS is also used to coat a thin and dense La2NiO4 (LNO) cathode layer. In this work, we have realized a complete cell on metallic support (ITM) produced by PLANSEE SE. The innovative LNO cathode layer was compared with screen-printed LNO layers, with and without RMS bonding layer. Electrochemical and Voltammetry tests were performed on these samples. It reveals lower perform…
Preparation of cholesteric particles from cellulose derivatives in a microfluidic setup
2011
A microfluidic setup was used to process lyotropic cholesteric liquid crystalline mixtures of cellulose derivatives into spherical particles in the micrometre scale. By the method of co-flowing injection, monodisperse droplets of the liquid crystal, dispersed in an aqueous carrier fluid, were prepared. Polymerization of the acrylic solvent with UV-light fixed the orientation obtained by the flowing motion. The resulting particles were characterized by polarizing optical microscopy.