Search results for "Equivalent circuit"

Pragmatic analysis of perovskite solar cells through a rationalized impedance spectroscopy equivalent circuit.

2020

Energy conversion from external fluctuating signals based on asymmetric nanopores

2015

Electrical transduction from fluctuating external signals is central to energy conversion based on nanoscale electrochemical devices and bioelectronics interfaces. We demonstrate theoretically and experimentally a significant energy transduction from white noise signals using the electrical rectification of asymmetric nanopores in polymeric membranes immersed in aqueous electrolyte solutions. Load capacitor voltages of the order of 1 V are obtained within times of the order of 1 min by means of nanofluidic diodes which convert zero time-average potentials of amplitudes of the order of 1 V into average net currents. We consider single-nanopore and multipore membranes to show that the convers…

Noise parameters of HEMTs: analysis of their properties from a circuit model approach

1996

Noise parameters of high electron mobility transistors (HEMT) at microwave frequencies are a subject of active research since the knowledge of their performance is of key importance for the use of these devices for designing low‐noise amplifiers. Employs a simple noise model to derive the analytical expressions for the device noise parameters F0, Γ0 and N in terms of the electrical elements associated with the basic equivalent circuit of an HEMT. Analyses such expressions to establish some fundamental relationships, as well as the expected noise performance of the device when the parasitic elements representing package effects are included.

Influence of the temperature on the equivalent noise resistance of HEMTs at microwave frequencies

1998

Abstract This paper is focused on the performance of the noise resistance Rn of HEMTs at microwave frequencies as a function of temperature. A sensitivity analysis has been performed on several noisy circuit models of low-noise devices that we had previously characterized in terms of scattering and noise parameters. Such a study has been aimed at pointing out the role played by either the electrical elements and the noise temperatures of the resistors of the equivalent circuit on the typically observed U-shaped behavior of Rn.

Typical Aspects of the Microwave Noise Performance of HEMTs at Decreasing Temperatures

1996

In analog signal processing at microwave frequencies the noise performance of active devices is of fundamental importance for the accurate design of low-noise amplifiers. To this aim, the determination of the four noise parameters F O , Γ O (complex variable) and Rn has to be accomplished together with the usual scattering parameter measurements vs. frequency. In addition, the dependence of the device performance vs. temperature is of interest for circuit applications characterized by harsh environmental conditions. In this work the noise behavior of high electron mobility transistors has been investigated by means of measurements and modeling in the 2-18 GHz frequency range and as a functi…

Sol-gel produced humidity sensor

1993

Abstract The sol-gel produced polycrystalline Prussian Blue thick films as planar humidity sensors have been investigated by impedance spectroscopy. The equivalent circuit used allows simulation in all the investigated r.h. range (10–100%). The region of changes of sample resistance is about five orders, which is enough for high measuring sensitivity.

RFID passive gas sensor integrating carbon nanotubes

2011

Carbon nanotube (CNT) composites are sensitive to the presence of gases due to their high surface-to-volume ratio and hollow structure that are well suited for gas molecule absorption and storage. Such sensing capability is here integrated with UHF RF identification (RFID) technology to achieve passive and low-cost sensors, remotely readable. CNT film (buckypaper) is used as a localized variable resistive load integrated into a tag antenna, which becomes able to transduce the presence of hazardous gas in the environment, ammonia in this case, into a change of its electromagnetic features. The dynamic range and the hysteresis of the radio sensor are investigated by simulations, equivalent ci…

A fully-automated procedure for measuring the electrical parameters of an induction motor drive with rotor at standstill

2003

The paper presents an automatic procedure to measure at standstill the electrical parameters of an induction motor fed by a PWM voltage source inverter. The proposed procedure executes automatically three tests using only the available PWM inverter control technique to obtain the required motor supply voltages. It allows the measurement of all the T-form circuit electrical parameters starting from the nameplate data as data-entry. It uses only a current sensor and no voltage sensor and process on line the collected data samples with a fast and easy to implement recursive least squares algorithm. Effectiveness of the automated procedure has been proved both by simulation and experimental tes…

An improved five-parameter model for photovoltaic modules

2010

This paper presents a new five-parameter model capable of analytically describing the I–V characteristic of a photovoltaic module for each generic condition of operative temperature and solar irradiance. The parameters of the equivalent electrical circuit are extracted by solving a system of equations based on data commonly issued by manufacturers in standard rating conditions with a trial and error process. The procedure, which does not require any special equations solver, can be easily coded into a short software routine using simple languages and finds the solution of the system of equations with the desired accuracy without needing to be guided towards solutions starting from fitted in…

A PV plant simulator for testing MPPT techniques

2013

This paper introduces a versatile and reliable photovoltaic systems simulator. It includes the main components of a photovoltaic plant: a PV string and a PWM controlled boost chooper. The key feature of this simulator is the ability to consider different and non-uniform irradiation and temperature conditions (partial shading and partial heating of the strings). All the different I-V and P-V or P-I characteristics can then be determined in such non-uniform irradiation and temperature conditions, with the aim to try different MPPT algorithms. The simulator also allows to verify an enhanced version of the Incremental Conductance algorithm (IncCond) where, in order to reach the real absolute ma…