Search results for "FAC"
showing 10 items of 36366 documents
In-process control strategies for friction stir welding of AZ31 sheets with non-uniform thickness
2017
Two different in-process control strategies were developed and compared with the aim to produce AZ31 magnesium alloy joints by friction stir welding on sheet blanks with a non-uniform thickness. To this purpose, sheets with dip or hump zones were welded by either changing the rotational speed or the tool plunging in order to keep constant the value of the vertical force occurring during the welding stage of the process. The influence of the main process parameters on the tool force, the micro- and macromechanical properties, and the joints microstructures in the dip and hump zones were analyzed. The results showed that using the rotational speed change-based approach, the hump zones are sub…
A new approach to simulate coating thickness in cold spray
2020
Abstract In the process of cold spray on complex components, the coating thickness is an important indicator to monitor and control. Current methods such as destructive tests or direct mechanical measurements can only be performed after spraying. Besides, these methods lead to production shutdown and additional costs . This article presents a novel approach predicting coating thickness for components with complex curved surfaces, especially in the case of shadow effects. Firstly, a three-dimensional geometric model of the coating profile based on Gaussian distribution was developed. In addition, the relative deposition efficiency (RDE) resulting from the different robot kinematic parameters…
Assessing the influence of fieldshaper material on magnetic pulse welded interface of Al/Cu joints
2019
Abstract Fieldshaper (FS) is a widely used component in magnetic pulse forming and welding to improve the efficiency of the process. It enables to increase the magnetic pressure experienced by the workpieces during forming and welding. Recent developments in this subject focuses to increase the life time of the fieldshaper and to improve the efficiency by introducing shape optimized designs. In this study, we compare the efficiency of four fieldshapers made of Cuprofor, Siclanic, CuBe2 and Steel. The main focus is given to the effect of material properties while the same geometry was considered for those four fieldshapers. The same welding conditions (discharge voltage of 6kV and air gap of…
On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper
2018
International audience; Machining has a particular impact on the surface integrity and on corrosion resistance of components. In fact, material removal induces geometrical, mechanical and micro-structural modifications in the machined surface and sub-surface that alter the electrochemical behavior of the material, and so the aging process. In this study, oxygen free high conductivity copper (OFHC) has machined under orthogonal cutting conditions using uncoated cemented carbide tools. Then, the corrosion resistance in 0.1 M NaCl salt fog atmosphere of the machined samples is analyzed. Finally, the optimal cutting conditions, including the tool geometry, for an improved corrosion resistance a…
Considerations Regarding the Industrial Implementation of Incremental Forming Process
2019
Incremental forming is a promising manufacturing process which allow the user to obtain sheet metal parts, in a flexible manner, without the use of a die. However, the industry is still reluctant to apply the process on an industrial scale. Several drawbacks of the process which hinder its industrial implementation are reviewed in the paper. Among them, the low accuracy of the parts and the low productivity of the process are considered. The lack of dedicated technological equipment and specific CAM software tools are also seen as major drawbacks. Moreover, the lack of any analytical tools to predict the plastic behaviour of the processed part and to predict the moment when it loses its int…
Improving surface integrity of additively manufactured GP1 stainless steel by roller burnishing
2020
Abstract Additive manufacturing can rapidly fabricate the desired components by selectively melting and solidifying feedstock, rather than conventional subtractive machining. However, the difference between the two routes in terms of surface integrity of the final component is relevant. This paper presents a strategy to control the surface characteristics of additively manufactured stainless steel by roller burnishing. In particular, process parameters have been carefully selected to improve the surface integrity of the worked material. The quality of the surface has been analyzed in terms of roughness, hardness, microstructure and residual stresses. The overall product endurance under high…
Magnetic field-assisted single-point incremental forming with a magnet ball tool
2021
Abstract This paper describes magnetic field-assisted single-point incremental forming (M-SPIF) with a Nd-Fe-B magnet ball tool. In M-SPIF, the tool driven by magnetic force plastically deforms a sheet. The polarity of the magnet tool helps to make the magnetic force (i.e., forming force) more controllable. In creating a truncated cone, the direction of the magnetic force gradually points more outward as the process progresses, and material is forced outwards from the cone center, increasing thinning in M-SPIF, while the cone center remains undeformed in traditional SPIF. Moreover, M-SPIF creates less localized plastic strain than traditional SPIF while forming the desired geometry.
Design of continuous Friction Stir Extrusion machines for metal chip recycling: issues and difficulties
2018
Abstract Friction Stir Extrusion is an innovative direct-recycling technology developed for metal machining chips. During the process, a rotating die is plunged into a cylindrical chamber containing the material to be recycled. The stirring action of the die prompts solid bonding phenomena allowing the back extrusion of a full dense rod. One of the main weakness of this technology is the discontinuity of the process itself that limits the extrudates volume to the capacity of the chamber. In order to overcome that limitation, a dedicated extrusion fixture has to be developed, keeping into account the concurrent needs of a continuous machine. The geometry of the die has to ensure proper press…
Friction Stir Welding of Ti6Al4V complex geometries for aeronautical applications: a feasibility study
2020
Abstract While Friction Stir Welding (FSW) of aluminium alloys can be considered a mature technology, even for complex joint morphologies, as T joints welded “in transparency”, welding of hard material still presents several open issues. In fact, welding of titanium alloys is a challenging process due to the chemical, mechanical and thermal characteristics of such materials which are subjected to atmosphere contamination resulting in joint hydrogen, oxygen and nitrogen embrittlement; additionally, due to the high melting temperature, large distortion and residual stress are found in joints obtained by traditional fusion welding processes as gas metal arc welding, electron beam welding and l…
Contactless generation of cavitation in high temperature liquid metals and its impact on particle dispersion in solidified iron and steel samples
2021
Abstract A recently developed method for the contactless magnetic generation of cavitation is demonstrated for high-melting-point metals. The approach is based on the floating-zone technique, which is truly contactless and crucible-free as it uses electromagnetic forces. Using this method, ultra-high-temperature ceramic particles, such as TiN, TiB2 and TiC, are admixed in liquid iron and 316L steel. The dispersion and particle refinement caused by cavitation treatment during melting and solidification are investigated. Magnetic fields up to 8 T that correspond to pressure oscillation amplitude of 0.83 MPa are used. The signal emitted by the collapsing bubbles is captured and visualized for …