Search results for "FLEX"
showing 10 items of 1677 documents
Effect of cobalt doping on the mechanical properties of ZnO nanowires
2016
Abstract In this work, we investigate the influence of doping on the mechanical properties of ZnO nanowires (NWs) by comparing the mechanical properties of pure and Co-doped ZnO NWs grown in similar conditions and having the same crystallographic orientation [0001]. The mechanical characterization included three-point bending tests made with atomic force microscopy and cantilever beam bending tests performed inside scanning electron microscopy. It was found that the Young's modulus of ZnO NWs containing 5% of Co was approximately a third lower than that of the pure ZnO NWs. Bending strength values were comparable for both materials and in both cases were close to theoretical strength indica…
Mechanical properties of sol–gel derived SiO2 nanotubes
2014
The mechanical properties of thick-walled SiO2 nanotubes (NTs) prepared by a sol–gel method while using Ag nanowires (NWs) as templates were measured by using different methods. In situ scanning electron microscopy (SEM) cantilever beam bending tests were carried out by using a nanomanipulator equipped with a force sensor in order to investigate plasticity and flexural response of NTs. Nanoindentation and three point bending tests of NTs were performed by atomic force microscopy (AFM) under ambient conditions. Half-suspended and three-point bending tests were processed in the framework of linear elasticity theory. Finite element method simulations were used to extract Young’s modulus values…
Sensing of the Molecular Spin in Spin-Crossover Nanoparticles with Micromechanical Resonators
2019
In the past years, the use of highly sensitive silicon microelectromechanical cantilevers has been proposed as a tool to characterize the spin-crossover phenomenon by employing fast optical readout of the motion. In this work, Fe II -based spin-crossover nanoparticles of the well-known [Fe(Htrz) 2 (trz)](BF 4 ) complex wrapped with thin silica shells of different sizes will be studied by means of silicon microresonators. The silica shell will enhance its chemical stability, whereas the low thickness will allow a proper mechanical coupling between the cantilever and the spin-crossover core. To maximize the sensing of the spin-crossover phenomena, different cantilever geometries and flexural…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Flexural strength and microhardness of anterior composites after accelerated aging
2016
Background This study aimed to evaluate the flexural strength and microhardness of three different anterior composites after 10 000 thermocycles. Material and Methods The mechanical properties of a nano-fill composite (Filtek Ultimate Universal Restorative (FUR) (Enamel)), a nano-hybrid composite (Clearfil Majesty ES2 (ES2) (Enamel)), and a micro-hybrid composite (G Aenial Anterior (GAA)) were investigated in this study. For the microhardness test, 8-mm diameter and 2-mm thickness composite discs were used (n = 10), and for the flexural strength test, 25x2x2 mm bar-shaped specimens were prepared (n = 13). The specimens were tested at 24 h and after 10 000 thermocycles. Data were analyzed us…
Stainless steel grids for confinement of clay brick masonry columns
2016
This work presents the results of an experimental investigation on the behavior of 21 solid clay brick columns internally strengthened by stainless steel grids placed in the horizontal joints of mortar. This reinforcing technique can be applied as a constructive technique for new construction or as a retrofitting technique for existing structures (old structures to be reconstructed by original constructive method and internal reinforcement). Monotonic compressive loading tests were carried out under concentric and eccentric load. The effects of different numbers of steel grids and eccentricity of the external load were examined. Also, a detailed characterization of the constituent materials…
Flexural and Shear Resistance of Steel Fiber–Reinforced Lightweight Concrete Beams
2014
In the present paper an analytical model is proposed that is able to determine the shear resistance of lightweight reinforced concrete beams with longitudinal bars, in the presence of reinforcing steel fibers. The model is based on the evaluation of the resistance contribution resulting from beam and arch actions. For the resistance contribution of main bars in tension, the residual bond adherence of steel bars and the crack spacing of reinforced concrete (RC) beams in the presence of fibers are considered. The contribution in terms of postcracking resistance in the tension zone of the beams is also included. The model was verified on the basis of experimental data available in the literatu…
MATERIALS AND PROCESSING ISSUES FOR THE MANUFACTURING OF INTEGRATED PASSIVE AND ACTIVE DEVICES ON FLEXIBLE SUBSTRATES
2008
Plast_ICs is a Public/Private Laboratory funded by Italian Government aimed to build a novel technological platform for the development of flexible electronics, mainly, but not solely, based on thin inorganic films. Integration of different functions, on single and/or multiple plastic foils, to generate a smart system is the final goal of the project. The building blocks of the platform will be presented, starting from the different plastic substrates characterization, going through the development of active devices, such as thin-film- transistors, and passive devices, like thin-film- resistors, capacitors, inductors. Fully inorganic elementary devices, based on optical patterning and in va…
Mechanical behavior of single-layer ceramized zirconia abutments for dental implant prosthetic rehabilitation
2013
Objectives: This study was undertaken to characterize the mechanical response of bare (as-received) and single-layer ceramized zirconia abutments with both internal and external connections that have been developed to enhanced aesthetic restorations. Material and Methods: Sixteen zirconia implant abutments (ZiReal Post®, Biomet 3i, USA) with internal and external connections have been analyzed. Half of the specimens were coated with a 0.5mm-thick layer of a low-fusing fluroapatite ceramic. Mechanical tests were carried out under static (constant cross-head speed of 1mm/min until fracture) and dynamic (between 100 and 400N at a frequency of 1Hz) loading conditions. The failure location was i…
Mechanical behavior of a sandwich with corrugated GRP core: numerical modeling and experimental validation
2014
In this work the mechanical behaviour of a core reinforced composite sandwich structure is studied. The sandwich employs a Glass Reinforced Polymer (GRP) orthotropic material for both the two external skins and the inner core web. In particular, the core is designed in order to cooperate with the GRP skins in membrane and flexural properties by means of the addition of a corrugated laminate into the foam core. An analytical model has been developed to replace a unit cell of this structure with an orthotropic equivalent thick plate that reproduces the in plane and out of plane behaviour of the original geometry. Different validation procedures have been implemented to verify the quality of t…