Search results for "FLEX"
showing 10 items of 1677 documents
Fibrous reinforced concrete beams in flexure: Experimental investigation, analytical modelling and design considerations
2008
Abstract The flexural behavior of plain and fibrous reinforced concrete (FRC) beams under monotonic and cyclic actions was analysed. Twelve beams were reinforced with top and bottom longitudinal deformed steel bars and transverse steel stirrups. Concrete, having 30 MPa cylindrical strength, was reinforced with hooked steel fibres at a volume percentage of 1%. Beams, 600 mm in length and with a square side cross-section of 150 mm, were tested in flexure using a three point bending test, adopting three different cover thicknesses of 5, 15 and 25 mm, respectively. The results obtained show that the addition of fibers increases the bearing capacity of the beams and ensures more ductile behaviou…
Three-Point Flexural Behaviour of GFRP Sandwich Composites: A Failure Map
2010
In this work, the failure mechanisms of GFRP/PVC foam core sandwich structures subjected to three-point bending are analysed. By varying the skin thickness (t ) and the span length between supports (l), experimental tests were carried out in order to find the relationship between the geometrical configuration of the sandwiches and the failure mechanism. By plotting failure mechanism on a graph of l against t , a failure map was created identifying the three typical failure mode regions of these sandwiches. The graph clearly shows the failure mode corresponding to each combination of l and t . To help optimise the use of these sandwich beams as structural elements, a theoretical failure mode…
Flexural behaviour of concrete corbels containing steel fibers or wrapped with FRP sheets
2005
In the present paper an analytical and experimental investigation referring to the flexural behaviour of reinforced concrete corbels subjected to vertical forces is presented. For fixed shape and dimensions of the corbels the experimental investigation analyses the effects of the following: longitudinal and transverse steel reinforcements; fiber reinforced concrete (FRC) with hooked steel fibers; external wrapping retrofitting technique with a thin layer of carbon fiber sheet (CFRP). The analytical model based on equivalent truss structures, allows one to determine the bearing capacity of corbels, distinguishing the different ultimate states reached. The analytical results are then compared…
Measuring the refractive state of an eye based on the intensity of the retinal reflex
2017
AbstractWhen examining the fundus of the eye with an ophthalmoscope, the intensity of the retinal reflex depends on the refractive state of the eye. In this study, application of this phenomenon for measuring the refractive state of the eye is demonstrated. First, a calibration curve relating the intensity of the retinal reflex and the refractive state was obtained using a model eye. Next, the intensity of the retinal reflex was measured while subjects were viewing a checker-board pattern, the distance of which was varied within the range from 0.17 to 1 m. Further, the relation between the refractive state and the optical power of the stimulus could be determined based on the measured light…
Integrated Optical Amplifier-Photodetector on a Wearable Nanocellulose Substrate
2018
Flexible optoelectronics has emerged as an outstanding platform to pave the road toward vanguard technology advancements. As compared to conventional rigid substrates, a flexible technology enables mechanical deformation while maintaining stable performance. The advantages include not only the development to novel applications, but also the implementation of a wearable technology directly in contact with a curved surface. Here the monolithic integration of a perovskite‐based optical waveguide amplifier together with a photodetector on a nanocellulose substrate is shown to demonstrate the feasibility of a stretchable signal manipulation and receptor system fabricated on a biodegradable mater…
Thermal atomic layer deposition of AlOxNy thin films for surface passivation of nano-textured flexible silicon
2019
Abstract Aluminum oxynitride (AlOxNy) films with different nitrogen concentration are prepared by thermal atomic layer deposition (ALD) for flexible nano-textured silicon (NT-Si) surface passivation. The AlOxNy films are shown to exhibit a homogeneous nitrogen-doping profile and the presence of an adequate amount of hydrogen, which is investigated by Time-of-Fight Elastic Recoil Detection Analysis (ToF-ERDA). The effective minority carrier lifetimes are measured after the NT-Si surface passivation; the minimum surface recombination velocity (SRV) of 5 cm-s−1 is achieved with the AlOxNy film in comparison to the Al2O3 and AlN films (SRV of 7–9 cm-s−1). The better SRV with AlOxNy film is due …
Reactive Powder Concrete Containing Basalt Fibers: Strength, Abrasion and Porosity
2020
The paper presents the test results of basalt fiber impact on a compressive and flexural strength, resistance to abrasion and porosity of Reactive Powder Concrete (RPC). The reasons for testing were interesting mechanical properties of basalt fibers, the significant tensile strength and flexural strength, and in particular the resistance to high temperatures, as well as a relatively small number of RPC tests performed with those fibers and different opinions regarding the impact of those fibers on concrete strength. The composition of the concrete mix was optimized to obtain the highest packing density of particles in the composite, based on the optimum particle size distribution curve acc.…
The influence of the rubber carboxyl functionality on the processability and properties of solid rubber modified epoxy mixtures
2005
A high molecular weight, carboxyl functionalised solid rubber was added to an epoxy resin-aromatic amino system developed for autoclave curing of honeycomb core composite structures. The achievement of an optimal balance of viscous flow and viscoelasticity of the resin, by controlling the nature and extent of cross-linking of the functionalised rubber, was proposed as a route to void-free honeycomb skins. The aim of the present investigation is to understand how the concentration of carboxylic groups of the rubber, prereacted with one of the epoxy monomers, affects the matrix resin flow properties. The concentration of carboxyl groups was changed by reacting them with a monofunctional epoxy…
Structural Behavior of Telescopic Steel Pipe for a Full-Scale 60 kW Wind Turbine Tower
2020
A simple analytical model, including local effects due to buckling and shear to moment interaction, was developed to pre-dict the load-carrying capacity of CHS tubes under flexure and shear. A finite-element analysis with ABAQUS Code was also conducted for validation of the proposed model. By properly modeling the imperfection effects due to the ovalization of steel tube, a good correlation of the structural response and failure mode was also achieved, and a good correlation with the analytical model was also achieved. Numerical and analytical results were compared with experimental results recently obtained by the author with good agreement. Experimental tests refer to full-scale static te…
TCSC allocation based on line flow based equations via mixed-integer programming
2007
Summary form only given. Research effort has been given to locate the optimal locations of thyristor-controlled series capacitor (TCSC) and their initial compensation levels using mixed-integer programming (MIP). As a useful technique for combinatorial optimisation over integer and continuous variables, the MIP approach can provide robust performance as well as high computational efficiency while solving complex optimal problems. Previous work using MIP employed DC load flow model ignoring reactive power balance, power loss and transformer tap ratios. In this paper, a new planning method is developed based on recently reported line flow equations and basic linearisation of binary-continuous…